Appendix A to Part 543 - Performance Criteria (Subsections 8 Through 21) of C.R.C, c. 1038.114 (in Effect March 30, 2011)
49:6.1.2.3.21.0.1.11.21 : Appendix A
Appendix A to Part 543 - Performance Criteria (Subsections 8
Through 21) of C.R.C, c. 1038.114 (in Effect March 30, 2011)
In order to be eligible for an exemption under § 543.7(a)(1),
the entire vehicle line must be equipped with an immobilizer
meeting the following criteria:
(1) Subject to paragraph (2) of this appendix, an immobilization
system shall arm automatically within a period of not more than 1
minute after the disarming device is removed from the vehicle, if
the vehicle remains in a mode of operation other than accessory
mode or on throughout that period.
(2) If the disarming device is a keypad or biometric identifier,
the immobilization system shall arm automatically within a period
of not more than 1 minute after the motors used for the vehicle's
propulsion are turned off, if the vehicle remains in a mode of
operation other than accessory mode or on throughout that
period.
(3) The immobilization system shall arm automatically not later
than 2 minutes after the immobilization system is disarmed,
unless:
(i) Action is taken for starting one or more motors used for the
vehicle's propulsion;
(ii) Disarming requires an action to be taken on the engine
start control or electric motor start control, the engine stop
control or electric motor stop control, or the ignition switch;
or
(iii) Disarming occurs automatically by the presence of a
disarming device and the device is inside the vehicle.
(4) If armed, the immobilization system shall prevent the
vehicle from moving more than 3 meters (9.8 feet) under its own
power by inhibiting the operation of at least one electronic
control unit and shall not have any impact on the vehicle's brake
system except that it may prevent regenerative braking and the
release of the parking brake.
(5) During the disarming process, a code shall be sent to the
inhibited electronic control unit in order to allow the vehicle to
move under its own power.
(6) It shall not be possible to disarm the immobilization system
by interrupting its normal operating voltage.
(7) When the normal starting procedure requires that the
disarming device mechanically latch into a receptacle and the
device is physically separate from the ignition switch key, one or
more motors used for the vehicle's propulsion shall start only
after the device is removed from that receptacle.
(8)(i) The immobilization system shall have a minimum capacity
of 50,000 code variants, shall not be disarmed by a code that can
disarm all other immobilization systems of the same make and model;
and
(ii) subject to paragraph (9) of this appendix, it shall not
have the capacity to process more than 5,000 codes within 24
hours.
(9) If an immobilization system uses rolling or encrypted codes,
it may conform to the following criteria instead of the criteria
set out in paragraph (8)(ii) of this appendix:
(i) The probability of obtaining the correct code within 24
hours shall not exceed 4 per cent; and
(ii) It shall not be possible to disarm the system by
re-transmitting in any sequence the previous 5 codes generated by
the system.
(10) The immobilization system shall be designed so that, when
tested as installed in the vehicle neither the replacement of an
original immobilization system component with a manufacturer's
replacement component nor the addition of a manufacturer's
component can be completed without the use of software; and it is
not possible for the vehicle to move under its own power for at
least 5 minutes after the beginning of the replacement or addition
of a component referred to in this paragraph (1).
(11) The immobilization system's conformity to paragraph (10) of
this appendix shall be demonstrated by testing that is carried out
without damaging the vehicle.
(12) Paragraph (10)(i) of this appendix does not apply to the
addition of a disarming device that requires the use of another
disarming device that is validated by the immobilization
system.
(13) The immobilization system shall be designed so that it can
neither be bypassed nor rendered ineffective in a manner that would
allow a vehicle to move under its own power, or be disarmed, using
one or more of the tools and equipment listed in paragraph (14) of
this appendix;
(i) Within a period of less than 5 minutes, when tested as
installed in the vehicle; or
(ii) Within a period of less than 2.5 minutes, when bench-tested
outside the vehicle.
(14) During a test referred to in paragraph (13) of this
appendix, only the following tools or equipment may be used:
Scissors, wire strippers, wire cutters and electrical wires, a
hammer, a slide hammer, a chisel, a punch, a wrench, a screwdriver,
pliers, steel rods and spikes, a hacksaw, a battery operated drill,
a battery operated angle grinder; and a battery operated
jigsaw.
Note:
C.R.C, c. 1038.114, Theft Protection and Rollaway Prevention (in
effect March 30, 2011). See: SOR/2011-69 March, 2011 “Regulations
Amending the Motor Vehicle Safety Regulations (Theft Prevention and
Rollaway Prevention - Standard 114)” 2011-03-30 Canada Gazette Part
II, Vol 145, No. 7.
[81 FR 66841, Sept. 29, 2016]