';


Title 40 Part 52 → Subpart O

Title 40 → Chapter I → Subchapter C → Part 52 → Subpart O

Electronic Code of Federal Regulations e-CFR

Title 40 Part 52 → Subpart O

e-CFR data is current as of August 22, 2019

Title 40Chapter ISubchapter CPart 52 → Subpart O


Title 40: Protection of Environment
PART 52—APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS


§52.719   [Reserved]

§52.720   Identification of plan.

(a) Purpose and scope. This section sets forth the applicable State implementation plan for the State of Illinois under section 110 of the Clean Air Act, 42 U.S.C. 7401-7671q and 40 CFR part 51 to meet national ambient air quality standards.

(b) Incorporation by reference. (1) Material listed in paragraphs (c) and (d) of this section with an EPA approval date prior to December 31, 2016, was approved for incorporation by reference by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Entries in paragraphs (c) and (d) of this section with the EPA approval dates after December 31, 2016, have been approved by EPA for inclusion in the State implementation plan and for incorporation by reference into the plan as it is contained in this section, and will be considered by the Director of the Federal Register for approval in the next update to the SIP compilation.

(2) EPA Region 5 certifies that the materials provided by EPA at the addresses in paragraph (b)(3) of this section are an exact duplicate of the officially promulgated state rules/regulations which have been approved as part of the state implementation plan as of the dates referenced in paragraph (b)(1).

(3) Copies of the materials incorporated by reference may be inspected at the Environmental Protection Agency, Region 5, Air Programs Branch, 77 West Jackson Boulevard, Chicago, IL 60604, or the National Archives and Records Administration. For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

(c) EPA approved regulations.

EPA-Approved Illinois Regulations and Statutes

Illinois citationTitle/subjectState
effective
date
EPA approval dateComments
Title 35 of the Illinois Administrative Code
Subtitle A: General Provisions
Chapter I: Pollution Control Board
Part 106: Procedural Regulations
Subpart E: Alternative Opacity Procedures
106.501Scope and Applicability7/13/198812/29/1992, 57 FR 61834
106.502Joint or Single Petition7/13/198812/29/1992, 57 FR 61834
106.503Request to Agency to Join as Co-Petitioner7/13/198812/29/1992, 57 FR 61834
106.504Contents of Petition7/13/198812/29/1992, 57 FR 61834
106.505Response and Reply7/13/198812/29/1992, 57 FR 61834
106.506Notice and Conduct of Hearing6/5/199012/29/1992, 57 FR 61834
106.507Opinions and Orders7/13/198812/29/1992, 57 FR 61834
Subpart J: Culpability Determinations
106.930Applicability7/11/19947/13/1995, 60 FR 36060
106.931Petition for Review7/11/19947/13/1995, 60 FR 36060
106.932Response and Reply7/11/19947/13/1995, 60 FR 36060
106.933Notice and Hearing7/11/19947/13/1995, 60 FR 36060
106.934Opinion and Order7/11/19947/13/1995, 60 FR 36060
Subtitle B: Air Pollution
Chapter I: Pollution Control Board
Subchapter a: Permits and General Provisions
Part 201: Permits and General Provisions
Subpart A: Definitions
201.102Definitions4/14/19725/31/1972, 37 FR 10862Approved as Rule 101.
Subpart B: General Provisions
201.121Existence of Permit No Defense4/14/19725/31/1972, 37 FR 10862Approved as Rule 103(h).
201.122Proof of Emissions4/14/19725/31/1972, 37 FR 10862Approved as Rule 108.
201.123Burden of Persuasion Regarding Exceptions4/14/19725/31/1972, 37 FR 10862Approved as Rule 111.
201.124Annual Report4/14/19725/31/1972, 37 FR 10862Approved as Rule 112.
201.125Severability4/14/19725/31/1972, 37 FR 10862Approved as Rule 113.
201.126Repealer4/14/19725/31/1972, 37 FR 10862Approved as Rule 114.
Subpart C: Prohibitions
201.141Prohibition of Air Pollution4/14/19725/31/1972, 37 FR 10862Approved as Rule 102.
201.142Construction Permit Required4/14/19725/31/1972, 37 FR 10862Approved as Rule 103(a)(1).
201.143Operating Permits for New Sources4/14/19725/31/1972, 37 FR 10862Approved as Rule 103(b)(1).
201.144Operating Permits for Existing Sources4/14/19725/31/1972, 37 FR 10862Approved as Rule 103(b)(2).
201.146Exemptions From State Permit Requirements3/24/201710/10/2018, 83 FR 50854Except (mmm).
201.147Former Permits4/14/19725/31/1972, 37 FR 10862Approved as Rule 103(j).
201.148Operation Without Compliance Program and Project Completion Schedule4/14/19725/31/1972, 37 FR 10862Approved as Rule 104(a).
201.149Operation During Malfunction, Breakdown or Startups4/14/19725/31/1972, 37 FR 10862Approved as Rule 105(a).
201.150Circumvention4/14/19725/31/1972, 37 FR 10862Approved as Rule 109.
201.151Design of Effluent Exhaust Systems4/14/19725/31/1972, 37 FR 10862Approved as Rule 110.
Subpart D: Permit Applications and Review Process
201.152Contents of Application for Construction Permit6/23/19981/3/2000, 65 FR 14
201.156Conditions4/14/19725/31/1972, 37 FR 10862Approved as Rule 103(a)(6).
201.157Contents of Application for Operating Permit6/23/19981/3/2000, 65 FR 14
201.158Incomplete Applications6/23/19981/3/2000, 65 FR 14
201.159Signatures6/23/19981/3/2000, 65 FR 14
201.160Standards for Issuance6/23/19981/3/2000, 65 FR 14
201.161Conditions4/14/19725/31/1972, 37 FR 10862Approved as Rule 103(b)(7).
201.162Duration12/1/20104/7/2014, 79 FR 18997
201.163Joint Construction and Operating Permits6/23/19981/3/2000, 65 FR 14
201.164Design Criteria6/23/19981/3/2000, 65 FR 14
201.165Hearings4/14/19725/31/1972, 37 FR 10862Approved as Rule 103(e).
201.166Revocation4/14/19725/31/1972, 37 FR 10862Approved as Rule 103(f).
201.167Revisions to Permits4/14/19725/31/1972, 37 FR 10862Approved as Rule 103(g).
201.168Appeals From Conditions4/14/19725/31/1972, 37 FR 10862Approved as Rule 103(k).
Subpart F: CAAPP Permits
201.207Applicability6/23/19981/3/2000, 65 FR 14
Subpart H: Compliance Programs and Project Completion Schedules
201.241Contents of Compliance Program4/14/19725/31/1972, 37 FR 10862Approved as Rule 104(b)(1).
201.242Contents of Project Completion Schedule4/14/19725/31/1972, 37 FR 10862Approved as Rule 104(b)(2, 3).
201.243Standards for Approval4/14/19725/31/1972, 37 FR 10862Approved as Rule 104(c).
201.244Revisions4/14/19725/31/1972, 37 FR 10862Approved as Rule 104(d).
201.245Effects of Approval4/14/19725/31/1972, 37 FR 10862Approved as Rule 104(e).
201.246Records and Reports4/14/19725/31/1972, 37 FR 10862Approved as Rule 104(f).
Subpart I: Malfunctions, Breakdowns or Startups
201.261Contents of Request for Permission To Operate During a Malfunction, Breakdown or Startup4/14/19725/31/1972, 37 FR 10862Approved as Rule 105(b).
201.262Standards for Granting Permission To Operate During a Malfunction, Breakdown or Startup4/14/19725/31/1972, 37 FR 10862Approved as Rule 105(c).
201.263Records and Reports4/14/19725/31/1972, 37 FR 10862Approved as Rule 105(d).
201.264Continued Operation or Startup Prior to Granting of Operating Permit4/14/19725/31/1972, 37 FR 10862Approved as Rule 105(e).
201.265Effect of Granting of Permission To Operate During a Malfunction, Breakdown or Startup4/14/19725/31/1972, 37 FR 10862Approved as Rule 105(f).
Subpart J: Monitoring and Testing
201.281Permit Monitoring Equipment Requirements2/3/19894/6/1993, 58 FR 17780
201.282Testing4/14/19725/31/1972, 37 FR 10862Approved as Rule 106(b).
201.283Records and Reports4/14/19725/31/1972, 37 FR 10862Approved as Rule 106(c).
Subpart K: Records and Reports
201.301Records4/14/19725/31/1972, 37 FR 10862Approved as Rule 107(a).
201.302Reports12/23/20133/13/2015, 80 FR 13248
Subpart L: Continuous Monitoring
201.401Continuous Monitoring Requirements2/3/19894/6/1993, 58 FR 17780
201.402Alternative Monitoring2/3/19894/6/1993, 58 FR 17780
201.403Exempt Sources2/3/19894/6/1993, 58 FR 17780
201.404Monitoring System Malfunction2/3/19894/6/1993, 58 FR 17780
201.405Excess Emission Reporting2/3/19894/6/1993, 58 FR 17780
201.406Data Reduction2/3/19894/6/1993, 58 FR 17780
201.407Retention of Information2/3/19894/6/1993, 58 FR 17780
201.408Compliance Schedules2/3/19894/6/1993, 58 FR 17780
Subpart M: Permit By Rule (PBR)—General Provisions
201.500Purpose3/24/201710/10/2018, 83 FR 50854
201.505Applicability3/24/201710/10/2018, 83 FR 50854
201.510Notice of Intent to Be Covered By a PBR (Notification)3/24/201710/10/2018, 83 FR 50854
201.515Commencing Construction or Modification3/24/201710/10/2018, 83 FR 50854
201.520Modification or Change in Status of an Emission Unit Covered by a PBR3/24/201710/10/2018, 83 FR 50854
201.525Standard Conditions for PBR3/24/201710/10/2018, 83 FR 50854
201.530Recordkeeping and Reporting3/24/201710/10/2018, 83 FR 50854
201.535Authority to Operate3/24/201710/10/2018, 83 FR 50854
201.540Enforcement Authority3/24/201710/10/2018, 83 FR 50854
Subpart N: Permit By Rule (PBR)—Boilers Less Than Or Equal To 100 MMBtu/hr
201.600Applicability3/24/201710/10/2018, 83 FR 50854
201.605Boiler Notice of Intent to Be Covered by a PBR (Notification) 201.6103/24/201710/10/2018, 83 FR 50854
201.615Opacity Requirements3/24/201710/10/2018, 83 FR 50854
201.620Requirements for Use of Diesel Fuel and Refinery Fuel Gas 201.6253/24/201710/10/2018, 83 FR 50854
201.625Carbon Monoxide (CO) Requirements3/24/201710/10/2018, 83 FR 50854
201.630Nitrogen Oxide (NOX) Requirements3/24/201710/10/2018, 83 FR 50854
201.635PBR Boiler Reporting Requirements3/24/201710/10/2018, 83 FR 50854
Part 203: Major Stationary Sources Construction and Modification
Subpart A: General Provisions
203.101Definitions4/30/19939/27/1995, 60 FR 49778
203.103Actual Construction3/22/198812/17/1992, 57 FR 59928
203.104Actual Emissions3/22/198812/17/1992, 57 FR 59928
203.107Allowable Emissions4/30/19939/27/1995, 60 FR 49778
203.110Available Growth Margin4/30/19939/27/1995, 60 FR 49778
203.112Building, Structure and Facility4/30/19939/27/1995, 60 FR 49778
203.113Commence3/22/198812/17/1992, 57 FR 59928
203.116Construction3/22/198812/17/1992, 57 FR 59928
203.117Dispersion Enhancement Techniques3/22/198812/17/1992, 57 FR 59928
203.119Emission Baseline7/22/198312/17/1992, 57 FR 59928
203.121Emission Offset4/30/19939/27/1995, 60 FR 49778
203.122Emissions Unit4/30/19939/27/1995, 60 FR 49778
203.123Federally Enforceable4/30/19939/27/1995, 60 FR 49778
203.124Fugitive Emissions3/22/198812/17/1992, 57 FR 59928
203.125Installation3/22/198812/17/1992, 57 FR 59928
203.126Lowest Achievable Emission Rate4/30/19939/27/1995, 60 FR 49778
203.127Nonattainment Area3/22/198812/17/1992, 57 FR 59928
203.128Potential To Emit4/30/19939/27/1995, 60 FR 49778
203.131Reasonable Further Progress3/22/198812/17/1992, 57 FR 59928
203.134Secondary Emissions3/22/198812/17/1992, 57 FR 59928
203.136Stationary Source3/22/198812/17/1992, 57 FR 59928
203.150Public Participation4/30/19939/27/1995, 60 FR 49778
Subpart B: Major Stationary Sources in Nonattainment Areas
203.201Prohibition4/30/19939/27/1995, 60 FR 49778
203.202Coordination With Permit Requirement and Application Pursuant to 35 Ill. Adm. Code 2013/22/198812/17/1992, 57 FR 59928
203.203Construction Permit Requirement and Application4/30/19939/27/1995, 60 FR 49778
203.205Effect of Permits3/22/198812/17/1992, 57 FR 59928
203.206Major Stationary Source3/10/19985/13/2003, 68 FR 25504
203.207Major Modification of a Source3/10/19985/13/2003, 68 FR 25504
203.208Net Emission Determination4/30/19939/27/1995, 60 FR 49778
203.209Significant Emissions Determination4/30/19939/27/1995, 60 FR 49778
203.210Relaxation of a Source-Specific Limitation3/22/198812/17/1992, 57 FR 59928
203.211Permit Exemption Based on Fugitive Emissions3/22/198812/17/1992, 57 FR 59928
Subpart C: Requirements for Major Stationary Sources in Nonattainment Areas
203.301Lowest Achievable Emission Rate3/10/19985/13/2003, 68 FR 25504
203.302Maintenance of Reasonable Further Progress and Emission Offsets4/30/19939/27/1995, 60 FR 49778
203.303Baseline and Emission Offsets Determination4/30/19939/27/1995, 60 FR 49778
203.305Compliance by Existing Sources3/22/198812/17/1992, 57 FR 59928
203.306Analysis of Alternatives4/30/19939/27/1995, 60 FR 49778
Subpart F: Operation of a Major Stationary Source or Major Modification
203.601Lowest Achievable Emission Rate Compliance Requirement3/22/198812/17/1992, 57 FR 59928
203.602Emission Offset Maintenance Requirement3/22/198812/17/1992, 57 FR 59928
Subpart G: General Maintenance of Emission Offsets
203.701General Maintenance of Emission Offsets3/22/198812/17/1992, 57 FR 59928
Subpart H: Offsets for Emission Increases From Rocket Engines and Motor Firing
203.801Offsetting by Alternative or Innovative Means5/14/19939/27/1995, 60 FR 49778
Subchapter b: Alternative Reduction Program
Part 205: Emissions Reduction Market System
Subpart A: General Provisions
205.100Severability11/25/199710/15/2001, 66 FR 52343
205.110Purpose11/25/199710/15/2001, 66 FR 52343
205.120Abbreviations and Acronyms6/13/20057/7/2008, 73 FR 38328
205.130Definitions6/13/20057/7/2008, 73 FR 38328
205.150Emissions Management Periods6/13/20057/7/2008, 73 FR 38328Except 150(e).
Subpart B: Applicability
205.200Participating Source6/13/20057/7/2008, 73 FR 38328
205.205Exempt Source6/13/20057/7/2008, 73 FR 38328
205.210New Participating Source6/13/20057/7/2008, 73 FR 38328
205.220Insignificant Emission Units6/13/20057/7/2008, 73 FR 38328
205.225Startup, Malfunction or Breakdown11/25/199710/15/2001, 66 FR 52343
Subpart C: Operational Implementation
205.300Seasonal Emissions Component of the Annual Emissions Report6/13/20057/7/2008, 73 FR 38328
205.310ERMS Applications6/13/20057/7/2008, 73 FR 38328
205.315CAAPP Permits for ERMS Sources6/13/20057/7/2008, 73 FR 38328
205.316Federally Enforceable State Operating Permits for ERMS Sources6/13/20057/7/2008, 73 FR 38328
205.318Certification for Exempt CAAPP Sources6/13/20057/7/2008, 73 FR 38328
205.320Baseline Emissions6/13/20057/7/2008, 73 FR 38328
205.330Emissions Determination Methods6/13/20057/7/2008, 73 FR 38328
205.335Sampling, Testing, Monitoring and Recordkeeping Practices6/13/20057/7/2008, 73 FR 38328
205.337Changes in Emissions Determination Methods and Sampling, Testing, Monitoring and Recordkeeping Practices6/13/20057/7/2008, 73 FR 38328
Subpart D: Seasonal Emissions Management
205.400Seasonal Emissions Allotment6/13/20057/7/2008, 73 FR 38328
205.405Exclusions From Further Reductions6/13/20057/7/2008, 73 FR 38328
205.410Participating Source Shutdowns6/13/20057/7/2008, 73 FR 38328
Subpart E: Alternative ATU Generation
205.500Emissions Reduction Generator6/13/20057/7/2008, 73 FR 38328
205.510Inter-Sector Transaction6/13/20057/7/2008, 73 FR 38328
Subpart F: Market Transactions
205.600ERMS Database11/25/199710/15/2001, 66 FR 52343
205.610Application for Transaction Account6/13/20057/7/2008, 73 FR 38328
205.620Account Officer11/25/199710/15/2001, 66 FR 52343
205.630ATU Transaction Procedures11/25/199710/15/2001, 66 FR 52343
Subpart G: Performance Accountability
205.700Compliance Accounting6/13/20057/7/2008, 73 FR 38328
205.710Alternative Compliance Market Account (ACMA)11/25/199710/15/2001, 66 FR 52343
205.720Emissions Excursion Compensation11/25/199710/15/2001, 66 FR 52343
205.730Excursion Reporting6/13/20057/7/2008, 73 FR 38328
205.740Enforcement Authority11/25/199710/15/2001, 66 FR 52343
205.750Emergency Conditions6/13/20057/7/2008, 73 FR 38328
205.760Market System Review Procedures6/13/20057/7/2008, 73 FR 38328
Subchapter c: Emission Standards and Limitations for Stationary Sources
Part 211: Definitions and General Provisions
Subpart A: General Provisions
211.101Incorporations by Reference1/28/201310/6/2014, 79 FR 60070
211.102Abbreviations and Conversion Factors9/14/20103/23/2012, 77 FR 16940
Subpart B: Definitions
211.121Other Definitions9/27/19939/9/1994, 59 FR 46562
211.130Accelacota9/27/19939/9/1994, 59 FR 46562
211.150Accumulator9/27/19939/9/1994, 59 FR 46562
211.170Acid Gases9/27/19939/9/1994, 59 FR 46562
211.200Acrylonitrile Butadiene Styrene (ABS) Welding9/14/20103/23/2012, 77 FR 16940
211.210Actual Heat Input9/27/19939/9/1994, 59 FR 46562
211.230Adhesive9/27/19939/9/1994, 59 FR 46562
211.233Adhesion Primer9/14/20103/23/2012, 77 FR 16940
211.235Adhesive Primer9/14/20103/23/2012, 77 FR 16940
211.240Adhesion Promoter5/9/19957/25/1996, 61 FR 38577
211.250Aeration9/27/19939/9/1994, 59 FR 46562
211.260Aerosol Adhesive and Adhesive Primer9/14/20103/23/2012, 77 FR 16940
211.270Aerosol Can Filling Line1/18/199410/21/1996, 61 FR 54556
211.290Afterburner9/27/19939/9/1994, 59 FR 46562
211.310Air Contaminant9/27/19939/9/1994, 59 FR 46562
211.330Air Dried Coatings9/27/19939/9/1994, 59 FR 46562
211.350Air Oxidation Process9/27/19939/9/1994, 59 FR 46562
211.370Air Pollutant9/27/19939/9/1994, 59 FR 46562
211.390Air Pollution9/27/19939/9/1994, 59 FR 46562
211.410Air Pollution Control Equipment9/27/19939/9/1994, 59 FR 46562
211.430Air Suspension Coater/Dryer9/27/19939/9/1994, 59 FR 46562
211.450Airless Spray9/27/19939/9/1994, 59 FR 46562
211.470Air Assisted Airless Spray9/27/19939/9/1994, 59 FR 46562
211.474Alcohol5/9/199511/8/1995, 60 FR 56238
211.481Ammunition Sealant9/14/20103/23/2012, 77 FR 16940
211.490Annual Grain Through Put9/27/19939/9/1994, 59 FR 46562
211.492Antifoulant Coating9/14/20103/23/2012, 77 FR 16940
211.493Antifouling Sealer/Tie Coat7/27/20113/23/2012, 77 FR 16940
211.495Anti-Glare/Safety Coating5/9/19957/25/1996, 61 FR 38577
211.510Application Area9/27/19939/9/1994, 59 FR 46562
211.530Architectural Coating9/27/19939/9/1994, 59 FR 46562
211.540Architectural Structure9/14/20103/23/2012, 77 FR 16940
211.550As Applied9/27/19939/9/1994, 59 FR 46562
211.560As-Applied Fountain Solution5/9/199511/8/1995, 60 FR 56238
211.570Asphalt9/27/19939/9/1994, 59 FR 46562
211.590Asphalt Prime Coat9/27/19939/9/1994, 59 FR 46562
211.610Automobile9/27/19939/9/1994, 59 FR 46562
211.630Automobile or Light Duty Truck Assembly Source or Automobile or Light Duty Truck Manufacturing Plant9/27/19939/9/1994, 59 FR 46562
211.650Automobile or Light Duty Truck Refinishing9/27/19939/9/1994, 59 FR 46562
211.660Automotive/Transportation Plastic Parts5/9/199510/26/1995, 60 FR 54807
211.670Baked Coatings5/9/199510/26/1995, 60 FR 54807
211.685Basecoat/Clearcoat System5/9/19957/25/1996, 61 FR 38577
211.690Batch Loading9/27/19939/9/1994, 59 FR 46562
211.695Batch Operation5/22/19954/2/1996, 61 FR 14484
211.696Batch Process Train5/22/19954/2/1996, 61 FR 14484
211.710Bead Dipping9/27/19939/9/1994, 59 FR 46562
211.715Bedliner9/14/20103/23/2012, 77 FR 16940
211.730Binders9/27/19939/9/1994, 59 FR 46562
211.735Black Coating9/14/20103/23/2012, 77 FR 16940
211.740Brakehorsepower (rated-bhp)9/25/20076/26/2009, 74 FR 30466
211.750British Thermal Unit9/27/19939/9/1994, 59 FR 46562
211.770Brush or Wipe Coating9/27/19939/9/1994, 59 FR 46562
211.790Bulk Gasoline Plant9/27/19939/9/1994, 59 FR 46562
211.810Bulk Gasoline Terminal9/27/19939/9/1994, 59 FR 46562
211.820Business Machine Plastic Parts9/14/20103/23/2012, 77 FR 16940
211.825Camouflage Coating9/14/20103/23/2012, 77 FR 16940
211.830Can9/27/19939/9/1994, 59 FR 46562
211.850Can Coating9/27/19939/9/1994, 59 FR 46562
211.870Can Coating Line9/27/19939/9/1994, 59 FR 46562
211.880Cap Sealant9/14/20103/23/2012, 77 FR 16940
211.890Capture9/27/19939/9/1994, 59 FR 46562
211.910Capture Device9/27/19939/9/1994, 59 FR 46562
211.930Capture Efficiency9/27/19939/9/1994, 59 FR 46562
211.950Capture System9/27/19939/9/1994, 59 FR 46562
211.954Cavity Wax9/14/20103/23/2012, 77 FR 16940
211.955Cement3/15/200111/8/2001, 66 FR 56449
211.960Cement Kiln3/15/200111/8/2001, 66 FR 56449
211.965Ceramic Tile Installation Adhesive9/14/20103/23/2012, 77 FR 16940
211.970Certified Investigation9/27/19939/9/1994, 59 FR 46562
211.980Chemical Manufacturing Process Unit5/9/19953/23/1998, 63 FR 13784
211.990Choke Loading9/27/19939/9/1994, 59 FR 46562
211.1000Class II Finish6/25/20103/23/2012, 77 FR 16940
211.1010Clean Air Act9/27/19939/9/1994, 59 FR 46562
211.1050Cleaning and Separating Operation9/27/19939/9/1994, 59 FR 46562
211.1070Cleaning Materials1/18/199410/21/1996, 61 FR 54556
211.1090Clear Coating9/27/19939/9/1994, 59 FR 46562
211.1110Clear Topcoat9/27/19939/9/1994, 59 FR 46562
211.1120Clinker3/15/200111/8/2001, 66 FR 56449
211.1128Closed Molding9/14/20103/23/2012, 77 FR 16940
211.1130Closed Purge System9/27/19939/9/1994, 59 FR 46562
211.1150Closed Vent System9/27/19939/9/1994, 59 FR 46562
211.1170Coal Refuse9/27/19939/9/1994, 59 FR 46562
211.1190Coating9/27/19939/9/1994, 59 FR 46562
211.1210Coating Applicator9/27/19939/9/1994, 59 FR 46562
211.1230Coating Line9/27/19939/9/1994, 59 FR 46562
211.1250Coating Plant9/27/19939/9/1994, 59 FR 46562
211.1270Coil Coating9/27/19939/9/1994, 59 FR 46562
211.1290Coil Coating Line9/27/19939/9/1994, 59 FR 46562
211.1310Cold Cleaning9/27/19939/9/1994, 59 FR 46562
211.1330Complete Combustion9/27/19939/9/1994, 59 FR 46562
211.1350Component9/27/19939/9/1994, 59 FR 46562
211.1370Concrete Curing Compounds9/27/19939/9/1994, 59 FR 46562
211.1390Concentrated Nitric Acid Manufacturing Process9/27/19939/9/1994, 59 FR 46562
211.1410Condensate9/27/19939/9/1994, 59 FR 46562
211.1430Condensible PM 109/27/19939/9/1994, 59 FR 46562
211.1455Contact Adhesive9/14/20103/23/2012, 77 FR 16940
211.1467Continuous Coater2/2/19985/19/1998, 63 FR 27489
211.1470Continuous Process9/27/19939/9/1994, 59 FR 46562
211.1490Control Device9/27/19939/9/1994, 59 FR 46562
211.1510Control Device Efficiency9/27/19939/9/1994, 59 FR 46562
211.1520Conventional Air Spray2/2/19985/19/1998, 63 FR 27489
211.1530Conventional Soybean Crushing Source9/27/19939/9/1994, 59 FR 46562
211.1550Conveyorized Degreasing9/27/19939/9/1994, 59 FR 46562
211.1560Cove Base9/14/20103/23/2012, 77 FR 16940
211.1565Cove Base Installation Adhesive9/14/20103/23/2012, 77 FR 16940
211.1570Crude Oil9/27/19939/9/1994, 59 FR 46562
211.1590Crude Oil Gathering9/27/19939/9/1994, 59 FR 46562
211.1610Crushing9/27/19939/9/1994, 59 FR 46562
211.1630Custody Transfer9/27/19939/9/1994, 59 FR 46562
211.1650Cutback Asphalt9/27/19939/9/1994, 59 FR 46562
211.1655Cyanoacrylate Adhesive9/14/20103/23/2012, 77 FR 16940
211.1670Daily Weighted Average VOM Content9/27/19939/9/1994, 59 FR 46562
211.1690Day9/27/19939/9/1994, 59 FR 46562
211.1700Deadener9/14/20103/23/2012, 77 FR 16940
211.1710Degreaser9/27/19939/9/1994, 59 FR 46562
211.1730Delivery Vessel9/27/19939/9/1994, 59 FR 46562
211.1740Diesel Engine9/25/20076/26/2009, 74 FR 30466
211.1745Digital Printing6/25/20103/23/2012, 77 FR 16940
211.1750Dip Coating9/27/19939/9/1994, 59 FR 46562
211.1770Distillate Fuel Oil9/27/19939/9/1994, 59 FR 46562
211.1780Distillation Unit5/9/19953/23/1998, 63 FR 13784
211.1790Drum9/27/19939/9/1994, 59 FR 46562
211.1810Dry Cleaning Operation or Dry Cleaning Facility9/27/19939/9/1994, 59 FR 46562
211.1830Dump Pit Area9/27/19939/9/1994, 59 FR 46562
211.1850Effective Grate Area9/27/19939/9/1994, 59 FR 46562
211.1870Effluent Water Separator9/27/19939/9/1994, 59 FR 46562
211.1872Ejection Cartridge Sealant9/14/20103/23/2012, 77 FR 16940
211.1875Elastomeric Materials5/9/19957/25/1996, 61 FR 38577
211.1876Electric Dissipating Coating9/14/20103/23/2012, 77 FR 16940
211.1877Electric-Insulating Varnish9/14/20103/23/2012, 77 FR 16940
211.1878Electrical Apparatus Component6/25/20103/23/2012, 77 FR 16940
211.1880Electrical Switchgear Compartment Coating9/14/20103/23/2012, 77 FR 16940
211.1882Electrodeposition Primer (EDP)9/14/20103/23/2012, 77 FR 16940
211.1883Electromagnetic Interference/Radio Frequency Interference (EMI/RFI) Shielding Coatings9/14/20103/23/2012, 77 FR 16940
211.1885Electronic Component6/25/20103/23/2012, 77 FR 16940
211.1890Electrostatic Bell or Disc Spray9/27/19939/9/1994, 59 FR 46562
211.1900Electrostatic Prep Coat5/9/199510/26/1995, 60 FR 54807
211.1910Electrostatic Spray9/27/19939/9/1994, 59 FR 46562
211.1920Emergency or Standby Unit9/25/20076/26/2009, 74 FR 30466
211.1930Emission Rate9/27/19939/9/1994, 59 FR 46562
211.1950Emission Unit9/27/19939/9/1994, 59 FR 46562
211.1970Enamel9/27/19939/9/1994, 59 FR 46562
211.1990Enclose9/27/19939/9/1994, 59 FR 46562
211.2010End Sealing Compound Coat9/27/19939/9/1994, 59 FR 46562
211.2030Enhanced Under-the-Cup Fill1/18/199410/21/1996, 61 FR 54556
211.2040Etching Filler9/14/20103/23/2012, 77 FR 16940
211.2050Ethanol Blend Gasoline9/27/19939/9/1994, 59 FR 46562
211.2055Ethylene Propylenediene Monomer (DPDM) Roof Membrane9/14/20103/23/2012, 77 FR 16940
211.2070Excess Air9/27/19939/9/1994, 59 FR 46562
211.2090Excessive Release9/27/19939/9/1994, 59 FR 46562
211.2130Existing Grain Handling Operation9/27/19939/9/1994, 59 FR 46562
211.2150Exterior Base Coat9/27/19939/9/1994, 59 FR 46562
211.2170Exterior End Coat9/27/19939/9/1994, 59 FR 46562
211.2190External Floating Roof9/27/19939/9/1994, 59 FR 46562
211.2200Extreme High-Gloss Coating7/27/20113/23/2012, 77 FR 16940
211.2210Extreme Performance Coating9/14/20103/23/2012, 77 FR 16940
211.2230Fabric Coating9/27/19939/9/1994, 59 FR 46562
211.2250Fabric Coating Line9/27/19939/9/1994, 59 FR 46562
211.2270Federally Enforceable Limitations and Conditions9/27/19939/9/1994, 59 FR 46562
211.2285Feed Mill6/17/19972/17/2000, 65 FR 8064
211.2300Fill11/15/19948/8/1996, 61 FR 41338
211.2310Final Repair Coat9/14/20103/23/2012, 77 FR 16940
211.2320Finish Primer Surfacer9/14/20103/23/2012, 77 FR 16940
211.2330Firebox9/27/19939/9/1994, 59 FR 46562
211.2350Fixed Roof Tank9/27/19939/9/1994, 59 FR 46562
211.2358Flat Wood Paneling7/27/20113/23/2012, 77 FR 16940
211.2359Flat Wood Paneling Coating Line6/25/20103/23/2012, 77 FR 16940
211.2360Flexible Coating9/14/20103/23/2012, 77 FR 16940
211.2365Flexible Operation Unit5/9/19953/23/1998, 63 FR 13784
211.2368Flexible Packaging6/25/20103/23/2012, 77 FR 16940
211.2369Flexible Vinyl9/14/20103/23/2012, 77 FR 16940
211.2370Flexographic Printing9/27/19939/9/1994, 59 FR 46562
211.2390Flexographic Printing Line9/27/19939/9/1994, 59 FR 46562
211.2410Floating Roof9/27/19939/9/1994, 59 FR 46562
211.2415Fog Coat9/14/20103/23/2012, 77 FR 16940
211.2430Fountain Solution9/27/19939/9/1994, 59 FR 46562
211.2450Freeboard Height9/27/19939/9/1994, 59 FR 46562
211.2470Fuel Combustion Emission Unit or Fuel Combustion Emission Source9/27/19939/9/1994, 59 FR 46562
211.2490Fugitive Particulate Matter9/27/19939/9/1994, 59 FR 46562
211.2510Full Operating Flowrate9/27/19939/9/1994, 59 FR 46562
211.2525Gasket/Gasket Sealing Material9/14/20103/23/2012, 77 FR 16940
211.2530Gas Service9/27/19939/9/1994, 59 FR 46562
211.2550Gas/Gas Method9/27/19939/9/1994, 59 FR 46562
211.2570Gasoline9/27/19939/9/1994, 59 FR 46562
211.2590Gasoline Dispensing Operation or Gasoline Dispensing Facility9/27/19939/9/1994, 59 FR 46562
211.2610Gel Coat1/18/199410/21/1996, 61 FR 54556
211.2615General Work Surface6/25/20103/23/2012, 77 FR 16940
211.2622Glass Bonding Primer9/14/20103/23/2012, 77 FR 16940
211.2630Gloss Reducers5/9/199510/26/1995, 60 FR 54807
211.2650Grain9/27/19939/9/1994, 59 FR 46562
211.2670Grain Drying Operation9/27/19939/9/1994, 59 FR 46562
211.2690Grain Handling and Conditioning Operation9/27/19939/9/1994, 59 FR 46562
211.2710Grain Handling Operation9/27/19939/9/1994, 59 FR 46562
211.2730Green Tire Spraying9/27/19939/9/1994, 59 FR 46562
211.2750Green Tires9/27/19939/9/1994, 59 FR 46562
211.2770Gross Heating Value9/27/19939/9/1994, 59 FR 46562
211.2790Gross Vehicle Weight Rating9/27/19939/9/1994, 59 FR 46562
211.2800Hardwood Plywood7/27/20113/23/2012, 77 FR 16940
211.2810Heated Airless Spray9/27/19939/9/1994, 59 FR 46562
211.2825Heat-Resistant Coating9/14/20103/23/2012, 77 FR 16940
211.2830Heatset6/25/20103/23/2012, 77 FR 16940
211.2840Heatset Web Letterpress Printing Line6/25/20103/23/2012, 77 FR 16940
211.2850Heatset Web Offset Lithographic Printing Line5/9/199511/8/1995, 60 FR 56238
211.2870Heavy Liquid1/28/201310/6/2014, 79 FR 60070
211.2890Heavy Metals9/27/19939/9/1994, 59 FR 46562
211.2910Heavy Off Highway Vehicle Products9/27/19939/9/1994, 59 FR 46562
211.2930Heavy Off Highway Vehicle Products Coating9/27/19939/9/1994, 59 FR 46562
211.2950Heavy Off Highway Vehicle Products Coating Line9/27/19939/9/1994, 59 FR 46562
211.2955High Bake Coating9/14/20103/23/2012, 77 FR 16940
211.2956High Build Primer Surfacer9/14/20103/23/2012, 77 FR 16940
211.2958High Gloss Coating9/14/20103/23/2012, 77 FR 16940
211.2960High-Performance Architectural Coating9/14/20103/23/2012, 77 FR 16940
211.2965High Precision Optic6/25/20103/23/2012, 77 FR 16940
211.2970High Temperature Aluminum Coating9/27/19939/9/1994, 59 FR 46562
211.2980High Temperature Coating9/14/20103/23/2012, 77 FR 16940
211.2990High Volume Low Pressure (HVLP) Spray9/27/19939/9/1994, 59 FR 46562
211.3010Hood9/27/19939/9/1994, 59 FR 46562
211.3030Hot Well9/27/19939/9/1994, 59 FR 46562
211.3050Housekeeping Practices9/27/19939/9/1994, 59 FR 46562
211.3070Incinerator9/27/19939/9/1994, 59 FR 46562
211.3090Indirect Heat Transfer9/27/19939/9/1994, 59 FR 46562
211.3095Indoor Floor Covering Installation Adhesive9/14/20103/23/2012, 77 FR 16940
211.3110Ink9/27/19939/9/1994, 59 FR 46562
211.3120In-Line Repair9/14/20103/23/2012, 77 FR 16940
211.3130In-Process Tank9/27/19939/9/1994, 59 FR 46562
211.3150In-Situ Sampling Systems9/27/19939/9/1994, 59 FR 46562
211.3170Interior Body Spray Coat9/27/19939/9/1994, 59 FR 46562
211.3190Internal Floating Roof9/27/19939/9/1994, 59 FR 46562
211.3210Internal Transferring Area9/27/19939/9/1994, 59 FR 46562
211.3215Janitorial Cleaning6/25/20103/23/2012, 77 FR 16940
211.3230Lacquers9/27/19939/9/1994, 59 FR 46562
211.3240Laminate9/14/20103/23/2012, 77 FR 16940
211.3250Large Appliance9/27/19939/9/1994, 59 FR 46562
211.3270Large Appliance Coating9/27/19939/9/1994, 59 FR 46562
211.3290Large Appliance Coating Line9/27/19939/9/1994, 59 FR 46562
211.3300Lean-Burn Engine9/25/20076/26/2009, 74 FR 30466
211.3305Letterpress Printing Line6/25/20103/23/2012, 77 FR 16940
211.3310Light Liquid9/27/19939/9/1994, 59 FR 46562
211.3330Light Duty Truck9/27/19939/9/1994, 59 FR 46562
211.3350Light Oil9/27/19939/9/1994, 59 FR 46562
211.3370Liquid/Gas Method9/27/19939/9/1994, 59 FR 46562
211.3390Liquid Mounted Seal9/27/19939/9/1994, 59 FR 46562
211.3410Liquid Service9/27/19939/9/1994, 59 FR 46562
211.3430Liquids Dripping9/27/19939/9/1994, 59 FR 46562
211.3450Lithographic Printing Line9/27/19939/9/1994, 59 FR 46562
211.3470Load Out Area9/27/19939/9/1994, 59 FR 46562
211.3480Loading Event10/25/19944/3/1995, 60 FR 16801
211.3483Long Dry Kiln3/15/200111/8/2001, 66 FR 56449
211.3485Long Wet Kiln3/15/200111/8/2001, 66 FR 56449
211.3487Low-NOX Burner3/15/200111/8/2001, 66 FR 56449
211.3490Low Solvent Coating9/27/19939/9/1994, 59 FR 46562
211.3505Lubricating Wax/Compound9/14/20103/23/2012, 77 FR 16940
211.3510Magnet Wire9/27/19939/9/1994, 59 FR 46562
211.3530Magnet Wire Coating9/27/19939/9/1994, 59 FR 46562
211.3550Magnet Wire Coating Line9/27/19939/9/1994, 59 FR 46562
211.3555Maintenance Cleaning6/25/20103/23/2012, 77 FR 16940
211.3570Major Dump Pit9/27/19939/9/1994, 59 FR 46562
211.3590Major Metropolitan Area (MMA)9/27/19939/9/1994, 59 FR 46562
211.3610Major Population Area (MPA)9/27/19939/9/1994, 59 FR 46562
211.3630Manufacturing Process9/27/19939/9/1994, 59 FR 46562
211.3650Marine Terminal10/25/19944/3/1995, 60 FR 16801
211.3660Marine Vessel10/25/19944/3/1995, 60 FR 16801
211.3665Mask Coating9/14/20103/23/2012, 77 FR 16940
211.3670Material Recovery Section9/27/19939/9/1994, 59 FR 46562
211.3690Maximum Theoretical Emissions9/27/19939/9/1994, 59 FR 46562
211.3695Maximum True Vapor Pressure11/15/19948/8/1996, 61 FR 41338
211.3705Medical Device6/25/20103/23/2012, 77 FR 16940
211.3707Medical Device and Pharmaceutical Manufacturing6/25/20103/23/2012, 77 FR 16940
211.3710Metal Furniture9/27/19939/9/1994, 59 FR 46562
211.3730Metal Furniture Coating9/27/19939/9/1994, 59 FR 46562
211.3750Metal Furniture Coating Line9/27/19939/9/1994, 59 FR 46562
211.3760Metallic Coating9/14/20103/23/2012, 77 FR 16940
211.3770Metallic Shoe Type Seal9/27/19939/9/1994, 59 FR 46562
211.3775Metal to Urethane/Rubber Molding or Casting Adhesive9/14/20103/23/2012, 77 FR 16940
211.3780Mid-Kiln Firing3/15/200111/8/2001, 66 FR 56449
211.3785Military Specification Coating9/14/20103/23/2012, 77 FR 16940
211.3790Miscellaneous Fabricated Product Manufacturing Process9/27/19939/9/1994, 59 FR 46562
211.3810Miscellaneous Formulation Manufacturing Process9/27/19939/9/1994, 59 FR 46562
211.3820Miscellaneous Industrial Adhesive Application Operation9/14/20103/23/2012, 77 FR 16940
211.3830Miscellaneous Metal Parts and Products9/27/19939/9/1994, 59 FR 46562
211.3850Miscellaneous Metal Parts and Products Coating9/27/19939/9/1994, 59 FR 46562
211.3870Miscellaneous Metal Parts or Products Coating Line9/27/19939/9/1994, 59 FR 46562
211.3890Miscellaneous Organic Chemical Manufacturing Process9/27/19939/9/1994, 59 FR 46562
211.3910Mixing Operation9/27/19939/9/1994, 59 FR 46562
211.3915Mobile Equipment5/9/19957/25/1996, 61 FR 38577
211.3925Mold Seal Coating9/14/20103/23/2012, 77 FR 16940
211.3930Monitor9/27/19939/9/1994, 59 FR 46562
211.3950Monomer1/18/199410/21/1996, 61 FR 54556
211.3960Motor Vehicles5/9/19957/25/1996, 61 FR 38577
211.3961Motor Vehicle Adhesive9/14/20103/23/2012, 77 FR 16940
211.3965Motor Vehicle Refinishing5/9/19957/25/1996, 61 FR 38577
211.3966Motor Vehicle Weatherstrip Adhesive9/14/20103/23/2012, 77 FR 16940
211.3967Mouth Waterproofing Sealant9/14/20103/23/2012, 77 FR 16940
211.3968Multi-Colored Coating9/14/20103/23/2012, 77 FR 16940
211.3969Multi-Component Coating9/14/20103/23/2012, 77 FR 16940
211.3970Multiple Package Coating9/27/19939/9/1994, 59 FR 46562
211.3975Multipurpose Construction Adhesive9/14/20103/23/2012, 77 FR 16940
211.3985Natural Finish Hardwood Plywood Panel7/27/20113/23/2012, 77 FR 16940
211.3990New Grain Drying Operation9/27/19939/9/1994, 59 FR 46562
211.4010New Grain Handling Operation9/27/19939/9/1994, 59 FR 46562
211.4030No Detectable Volatile Organic Material Emissions9/27/19939/9/1994, 59 FR 46562
211.4050Non-Contact Process Water Cooling Tower1/18/199410/21/1996, 61 FR 54556
211.4052Non-Convertible Coating9/14/20103/23/2012, 77 FR 16940
211.4055Non-Flexible Coating5/9/199510/26/1995, 60 FR 54807
211.4065Non-Heatset6/25/20103/23/2012, 77 FR 16940
211.4067NOX Trading Program4/17/200111/8/2001, 66 FR 56449
211.4070Offset9/27/19939/9/1994, 59 FR 46562
211.4080One-Component Coating9/14/20103/23/2012, 77 FR 16940
211.4090One Hundred Percent Acid9/27/19939/9/1994, 59 FR 46562
211.4110One Turn Storage Space9/27/19939/9/1994, 59 FR 46562
211.4130Opacity9/27/19939/9/1994, 59 FR 46562
211.4150Opaque Stains9/27/19939/9/1994, 59 FR 46562
211.4170Open Top Vapor Degreasing9/27/19939/9/1994, 59 FR 46562
211.4190Open Ended Valve9/27/19939/9/1994, 59 FR 46562
211.4210Operator of a Gasoline Dispensing Operation or Operator of a Gasoline Dispensing Facility9/27/19939/9/1994, 59 FR 46562
211.4220Optical Coating9/14/20103/23/2012, 77 FR 16940
211.4230Organic Compound9/27/19939/9/1994, 59 FR 46562
211.4250Organic Material and Organic Materials10/19/19953/21/1996, 61 FR 11550
211.4260Organic Solvent10/19/19953/21/1996, 61 FR 11550
211.4270Organic Vapor9/27/19939/9/1994, 59 FR 46562
211.4285Outdoor Floor Covering Installation Adhesive9/14/20103/23/2012, 77 FR 16940
211.4290Oven9/27/19939/9/1994, 59 FR 46562
211.4310Overall Control9/27/19939/9/1994, 59 FR 46562
211.4330Overvarnish9/27/19939/9/1994, 59 FR 46562
211.4350Owner of a Gasoline Dispensing Operation or Owner of a Gasoline Dispensing Facility9/27/19939/9/1994, 59 FR 46562
211.4370Owner or Operator9/27/19939/9/1994, 59 FR 46562
211.4390Packaging Rotogravure Printing9/27/19939/9/1994, 59 FR 46562
211.4410Packaging Rotogravure Printing Line9/27/19939/9/1994, 59 FR 46562
211.4430Pail9/27/19939/9/1994, 59 FR 46562
211.4450Paint Manufacturing Source or Paint Manufacturing Plant9/27/19939/9/1994, 59 FR 46562
211.4455Pan-Backing Coating9/14/20103/23/2012, 77 FR 16940
211.4460Panel7/27/20113/23/2012, 77 FR 16940
211.4470Paper Coating9/27/19939/9/1994, 59 FR 46562
211.4490Paper Coating Line9/27/19939/9/1994, 59 FR 46562
211.4510Particulate Matter9/27/19939/9/1994, 59 FR 46562
211.4530Parts per Million (Volume) or Ppm (VOL)9/27/19939/9/1994, 59 FR 46562
211.4540Perimeter Bonded Sheet Flooring9/14/20103/23/2012, 77 FR 16940
211.4550Person9/27/19939/9/1994, 59 FR 46562
211.4590Petroleum9/27/19939/9/1994, 59 FR 46562
211.4610Petroleum Liquid10/19/19953/21/1996, 61 FR 11550
211.4630Petroleum Refinery9/27/19939/9/1994, 59 FR 46562
211.4650Pharmaceutical9/27/19939/9/1994, 59 FR 46562
211.4670Pharmaceutical Coating Operation9/27/19939/9/1994, 59 FR 46562
211.4690Photochemically Reactive Material9/27/19939/9/1994, 59 FR 46562
211.4710Pigmented Coatings9/27/19939/9/1994, 59 FR 46562
211.4730Plant9/27/19939/9/1994, 59 FR 46562
211.4735Plastic9/14/20103/23/2012, 77 FR 16940
211.4740Plastic Part5/9/199510/26/1995, 60 FR 54807
211.4750Plasticizers9/27/19939/9/1994, 59 FR 46562
211.4760Plastic Solvent Welding Adhesive9/14/20103/23/2012, 77 FR 16940
211.4765Plastic Solvent Welding Adhesive Primer9/14/20103/23/2012, 77 FR 16940
211.4768Pleasure Craft9/14/20103/23/2012, 77 FR 16940
211.4769Pleasure Craft Surface Coating9/14/20103/23/2012, 77 FR 16940
211.4770PM 109/27/19939/9/1994, 59 FR 46562
211.4790Pneumatic Rubber Tire Manufacture9/27/19939/9/1994, 59 FR 46562
211.4810Polybasic Organic Acid Partial Oxidation Manufacturing Process9/27/19939/9/1994, 59 FR 46562
211.4830Polyester Resin Material(s)1/18/199410/21/1996, 61 FR 54556
211.4850Polyester Resin Products Manufacturing Process1/18/199410/21/1996, 61 FR 54556
211.4870Polystyrene Plant9/27/19939/9/1994, 59 FR 46562
211.4890Polystyrene Resin9/27/19939/9/1994, 59 FR 46562
211.4895Polyvinyl Chloride Plastic (PVC Plastic)9/14/20103/23/2012, 77 FR 16940
211.4900Porous Material9/14/20103/23/2012, 77 FR 16940
211.4910Portable Grain Handling Equipment9/27/19939/9/1994, 59 FR 46562
211.4930Portland Cement Manufacturing Process Emission Source9/27/19939/9/1994, 59 FR 46562
211.4950Portland Cement Process or Portland Cement Manufacturing Plant9/27/19939/9/1994, 59 FR 46562
211.4970Potential To Emit1/18/199410/21/1996, 61 FR 54556
211.4990Power Driven Fastener Coating9/27/19939/9/1994, 59 FR 46562
211.5010Precoat5/9/19957/25/1996, 61 FR 38577
211.5012Prefabricated Architectural Coating9/14/20103/23/2012, 77 FR 16940
211.5015Preheater Kiln3/15/200111/8/2001, 66 FR 56449
211.5020Preheater/Precalciner Kiln3/15/200111/8/2001, 66 FR 56449
211.5030Pressure Release9/27/19939/9/1994, 59 FR 46562
211.5050Pressure Tank9/27/19939/9/1994, 59 FR 46562
211.5060Pressure/Vacuum Relief Valve9/21/19941/27/1995, 60 FR 5318
211.5061Pretreatment Coating9/14/20103/23/2012, 77 FR 16940
211.5062Pretreatment Wash Primer9/14/20103/23/2012, 77 FR 16940
211.5065Primary Product5/9/19953/23/1998, 63 FR 13784
211.5070Prime Coat9/27/19939/9/1994, 59 FR 46562
211.5075Primer Sealant9/14/20103/23/2012, 77 FR 16940
211.5080Primer Sealer5/9/19957/25/1996, 61 FR 38577
211.5090Primer Surfacer Coat9/14/20103/23/2012, 77 FR 16940
211.5110Primer Surfacer Operation9/27/19939/9/1994, 59 FR 46562
211.5130Primers9/27/19939/9/1994, 59 FR 46562
211.5140Printed Interior Panel7/27/20113/23/2012, 77 FR 16940
211.5150Printing9/27/19939/9/1994, 59 FR 46562
211.5170Printing Line9/27/19939/9/1994, 59 FR 46562
211.5185Process Emission Source9/27/19939/9/1994, 59 FR 46562
211.5190Process Emission Unit9/27/19939/9/1994, 59 FR 46562
211.5210Process Unit9/27/19939/9/1994, 59 FR 46562
211.5230Process Unit Shutdown9/27/19939/9/1994, 59 FR 46562
211.5245Process Vent5/22/19954/2/1996, 61 FR 14484
211.5250Process Weight Rate9/27/19939/9/1994, 59 FR 46562
211.5270Production Equipment Exhaust System9/27/19939/9/1994, 59 FR 46562
211.5310Publication Rotogravure Printing Line9/27/19939/9/1994, 59 FR 46562
211.5330Purged Process Fluid9/27/19939/9/1994, 59 FR 46562
211.5335Radiation Effect Coating6/25/20103/23/2012, 77 FR 16940
211.5350Reactor9/27/19939/9/1994, 59 FR 46562
211.5370Reasonably Available Control Technology (RACT)9/27/19939/9/1994, 59 FR 46562
211.5390Reclamation System1/18/199410/21/1996, 61 FR 54556
211.5400Red Coating9/14/20103/23/2012, 77 FR 16940
211.5410Refiner9/27/19939/9/1994, 59 FR 46562
211.5430Refinery Fuel Gas9/27/19939/9/1994, 59 FR 46562
211.5450Refinery Fuel Gas System9/27/19939/9/1994, 59 FR 46562
211.5470Refinery Unit or Refinery Process Unit9/27/19939/9/1994, 59 FR 46562
211.5480Reflective Argent Coating5/9/199510/26/1995, 60 FR 54807
211.5490Refrigerated Condenser9/27/19939/9/1994, 59 FR 46562
211.5500Regulated Air Pollutant12/7/19934/5/1995, 60 FR 17229
211.5510Reid Vapor Pressure1/28/201310/6/2014, 79 FR 60070
211.5520Reinforced Plastic Composite9/14/20103/23/2012, 77 FR 16940
211.5530Repair1/18/199410/21/1996, 61 FR 54556
211.5535Repair Cleaning6/25/20103/23/2012, 77 FR 16940
211.5550Repair Coat9/14/20103/23/2012, 77 FR 16940
211.5570Repaired9/27/19939/9/1994, 59 FR 46562
211.5585Research and Development Operation6/25/20103/23/2012, 77 FR 16940
211.5590Residual Fuel Oil9/27/19939/9/1994, 59 FR 46562
211.5600Resist Coat5/9/199510/26/1995, 60 FR 54807
211.5610Restricted Area9/27/19939/9/1994, 59 FR 46562
211.5630Retail Outlet9/27/19939/9/1994, 59 FR 46562
211.5640Rich-Burn Engine9/25/20076/26/2009, 74 FR 30466
211.5650Ringelmann Chart9/27/19939/9/1994, 59 FR 46562
211.5670Roadway9/27/19939/9/1994, 59 FR 46562
211.5690Roll Coater9/27/19939/9/1994, 59 FR 46562
211.5710Roll Coating9/27/19939/9/1994, 59 FR 46562
211.5730Roll Printer9/27/19939/9/1994, 59 FR 46562
211.5750Roll Printing9/27/19939/9/1994, 59 FR 46562
211.5770Rotogravure Printing9/27/19939/9/1994, 59 FR 46562
211.5790Rotogravure Printing Line9/27/19939/9/1994, 59 FR 46562
211.5800Rubber9/14/20103/23/2012, 77 FR 16940
211.5810Safety Relief Valve9/27/19939/9/1994, 59 FR 46562
211.5830Sandblasting9/27/19939/9/1994, 59 FR 46562
211.5850Sanding Sealers9/27/19939/9/1994, 59 FR 46562
211.5860Scientific Instrument6/25/20103/23/2012, 77 FR 16940
211.5870Screening9/27/19939/9/1994, 59 FR 46562
211.5875Screen Printing6/25/20103/23/2012, 77 FR 16940
211.5885Screen Reclamation6/25/20103/23/2012, 77 FR 16940
211.5890Sealer9/14/20103/23/2012, 77 FR 16940
211.5910Semi Transparent Stains9/27/19939/9/1994, 59 FR 46562
211.5930Sensor9/27/19939/9/1994, 59 FR 46562
211.5950Set of Safety Relief Valves9/27/19939/9/1994, 59 FR 46562
211.5970Sheet Basecoat9/27/19939/9/1994, 59 FR 46562
211.5980Sheet-Fed5/9/199511/8/1995, 60 FR 56238
211.5985Sheet Rubber Lining Installation9/14/20103/23/2012, 77 FR 16940
211.5987Shock-Free Coating9/14/20103/23/2012, 77 FR 16940
211.5990Shotblasting9/27/19939/9/1994, 59 FR 46562
211.6010Side Seam Spray Coat9/27/19939/9/1994, 59 FR 46562
211.6012Silicone-Release Coating9/14/20103/23/2012, 77 FR 16940
211.6015Single-Ply Roof Membrane9/14/20103/23/2012, 77 FR 16940
211.6017Single-Ply Roof Membrane Adhesive Primer9/14/20103/23/2012, 77 FR 16940
211.6020Single-Ply Roof Membrane Installation and Repair Adhesive9/14/20103/23/2012, 77 FR 16940
211.6025Single Unit Operation5/22/19954/2/1996, 61 FR 14484
211.6030Smoke9/27/19939/9/1994, 59 FR 46562
211.6050Smokeless Flare9/27/19939/9/1994, 59 FR 46562
211.6060Soft Coat5/9/199510/26/1995, 60 FR 54807
211.6063Solar-Absorbent Coating9/14/20103/23/2012, 77 FR 16940
211.6065Solids Turnover Ratio (RT)9/14/20103/23/2012, 77 FR 16940
211.6070Solvent9/27/19939/9/1994, 59 FR 46562
211.6090Solvent Cleaning9/27/19939/9/1994, 59 FR 46562
211.6110Solvent Recovery System1/18/199410/21/1996, 61 FR 54556
211.6130Source4/17/200111/8/2001, 66 FR 56449
211.6140Specialty Coatings5/9/199510/26/1995, 60 FR 54807
211.6145Specialty Coatings for Motor Vehicles5/9/19957/25/1996, 61 FR 38577
211.6150Specialty High Gloss Catalyzed Coating9/27/19939/9/1994, 59 FR 46562
211.6170Specialty Leather1/18/199410/21/1996, 61 FR 54556
211.6190Specialty Soybean Crushing Source9/27/19939/9/1994, 59 FR 46562
211.6210Splash Loading9/27/19939/9/1994, 59 FR 46562
211.6230Stack9/27/19939/9/1994, 59 FR 46562
211.6250Stain Coating1/18/199410/21/1996, 61 FR 54556
211.6270Standard Conditions9/27/19939/9/1994, 59 FR 46562
211.6290Standard Cubic Foot (Scf)9/27/19939/9/1994, 59 FR 46562
211.6310Start Up9/27/19939/9/1994, 59 FR 46562
211.6330Stationary Emission Source9/27/19939/9/1994, 59 FR 46562
211.6350Stationary Emission Unit9/27/19939/9/1994, 59 FR 46562
211.6370Stationary Source9/27/19939/9/1994, 59 FR 46562
211.6390Stationary Storage Tank9/27/19939/9/1994, 59 FR 46562
211.6400Stencil Coat9/14/20103/23/2012, 77 FR 16940
211.6405Sterilization Indicating Ink6/25/20103/23/2012, 77 FR 16940
211.6410Storage Tank or Storage Vessel9/27/19939/9/1994, 59 FR 46562
211.6420Strippable Spray Booth Coating2/2/19985/19/1998, 63 FR 27489
211.6425Stripping6/25/20103/23/2012, 77 FR 16940
211.6427Structural Glazing9/14/20103/23/2012, 77 FR 16940
211.6430Styrene Devolatilizer Unit9/27/19939/9/1994, 59 FR 46562
211.6450Styrene Recovery Unit9/27/19939/9/1994, 59 FR 46562
211.6460Subfloor9/14/20103/23/2012, 77 FR 16940
211.6470Submerged Loading Pipe9/27/19939/9/1994, 59 FR 46562
211.6490Substrate9/27/19939/9/1994, 59 FR 46562
211.6510Sulfuric Acid Mist9/27/19939/9/1994, 59 FR 46562
211.6530Surface Condenser9/27/19939/9/1994, 59 FR 46562
211.6535Surface Preparation6/25/20103/23/2012, 77 FR 16940
211.6540Surface Preparation Materials5/9/19957/25/1996, 61 FR 38577
211.6550Synthetic Organic Chemical or Polymer Manufacturing Plant9/27/19939/9/1994, 59 FR 46562
211.6570Tablet Coating Operation9/27/19939/9/1994, 59 FR 46562
211.6580Texture Coat5/9/199510/26/1995, 60 FR 54807
211.6585Thin Metal Laminating Adhesive9/14/20103/23/2012, 77 FR 16940
211.6587Thin Particleboard7/27/20113/23/2012, 77 FR 16940
211.6590Thirty Day Rolling Average9/27/19939/9/1994, 59 FR 46562
211.6610Three Piece Can9/27/19939/9/1994, 59 FR 46562
211.6620Three or Four Stage Coating System5/9/19957/25/1996, 61 FR 38577
211.6630Through-the-Valve Fill1/18/199410/21/1996, 61 FR 54556
211.6635Tileboard7/27/20113/23/2012, 77 FR 16940
211.6640Tire Repair9/14/20103/23/2012, 77 FR 16940
211.6650Tooling Resin1/18/199410/21/1996, 61 FR 54556
211.6670Topcoat9/14/20103/23/2012, 77 FR 16940
211.6690Topcoat Operation9/14/20103/23/2012, 77 FR 16940
211.6695Topcoat System5/9/19957/25/1996, 61 FR 38577
211.6710Touch-Up1/18/199410/21/1996, 61 FR 54556
211.6720Touch-Up Coating9/14/20103/23/2012, 77 FR 16940
211.6730Transfer Efficiency9/27/19939/9/1994, 59 FR 46562
211.6740Translucent Coating9/14/20103/23/2012, 77 FR 16940
211.6750Tread End Cementing9/27/19939/9/1994, 59 FR 46562
211.6770True Vapor Pressure9/27/19939/9/1994, 59 FR 46562
211.6780Trunk Interior Coating9/14/20103/23/2012, 77 FR 16940
211.6790Turnaround9/27/19939/9/1994, 59 FR 46562
211.6810Two Piece Can9/27/19939/9/1994, 59 FR 46562
211.6825Underbody Coating9/14/20103/23/2012, 77 FR 16940
211.6830Under-the-Cup Fill1/18/199410/21/1996, 61 FR 54556
211.6850Undertread Cementing9/27/19939/9/1994, 59 FR 46562
211.6860Uniform Finish Blender5/9/19957/25/1996, 61 FR 38577
211.6870Unregulated Safety Relief Valve9/27/19939/9/1994, 59 FR 46562
211.6880Vacuum Metallizing5/9/199510/26/1995, 60 FR 54807
211.6885Vacuum Metalizing Coating9/14/20103/23/2012, 77 FR 16940
211.6890Vacuum Producing System9/27/19939/9/1994, 59 FR 46562
211.6910Vacuum Service9/27/19939/9/1994, 59 FR 46562
211.6930Valves Not Externally Regulated9/27/19939/9/1994, 59 FR 46562
211.6950Vapor Balance System9/27/19939/9/1994, 59 FR 46562
211.6970Vapor Collection System10/25/19944/3/1995, 60 FR 16801
211.6990Vapor Control System10/25/19944/3/1995, 60 FR 16801
211.7010Vapor Mounted Primary Seal9/27/19939/9/1994, 59 FR 46562
211.7030Vapor Recovery System9/27/19939/9/1994, 59 FR 46562
211.7050Vapor-Suppressed Polyester Resin1/18/199410/21/1996, 61 FR 54556
211.7070Vinyl Coating9/27/19939/9/1994, 59 FR 46562
211.7090Vinyl Coating Line9/27/19939/9/1994, 59 FR 46562
211.7110Volatile Organic Liquid (VOL)9/27/19939/9/1994, 59 FR 46562
211.7130Volatile Organic Material Content (VOMC)9/27/19939/9/1994, 59 FR 46562
211.7150Volatile Organic Material (VOM) or Volatile Organic Compound (VOC)10/23/201712/21/2018, 83 FR 65537
211.7170Volatile Petroleum Liquid9/27/19939/9/1994, 59 FR 46562
211.7190Wash Coat9/27/19939/9/1994, 59 FR 46562
211.7200Washoff Operations2/2/19985/19/1998, 63 FR 27489
211.7210Wastewater (Oil/Water) Separator9/27/19939/9/1994, 59 FR 46562
211.7220Waterproof Resorcinol Glue9/14/20103/23/2012, 77 FR 16940
211.7230Weak Nitric Acid Manufacturing Process9/27/19939/9/1994, 59 FR 46562
211.7240Weatherstrip Adhesive9/14/20103/23/2012, 77 FR 16940
211.7250Web9/27/19939/9/1994, 59 FR 46562
211.7270Wholesale Purchase Consumer9/27/19939/9/1994, 59 FR 46562
211.7290Wood Furniture6/25/20103/23/2012, 77 FR 16940
211.7310Wood Furniture Coating9/27/19939/9/1994, 59 FR 46562
211.7330Wood Furniture Coating Line9/27/19939/9/1994, 59 FR 46562
211.7350Woodworking9/27/19939/9/1994, 59 FR 46562
Part 212: Visible and Particulate Matter Emissions
Subpart A: General
212.107Measurement Method for Visible Emissions5/22/19963/11/1998, 63 FR 11842
212.108Measurement Methods for PM-10 Emissions and Condensible PM-10 Emissions5/22/19963/11/1998, 63 FR 11842
212.109Measurement Methods for Opacity5/22/19963/11/1998, 63 FR 11842
212.110Measurement Methods for Particulate Matter5/22/19963/11/1998, 63 FR 11842
212.111Abbreviations and Units10/4/199110/21/1993, 58 FR 54291
212.113Incorporations by Reference5/22/19967/14/1999, 64 FR 37847
Subpart B: Visible Emissions
212.121Opacity Standards7/13/198812/29/1992, 57 FR 61834
212.122Visible Emissions Limitations for Certain Emission Units for Which Construction or Modification Commenced on or After April 14, 19727/13/198812/29/1992, 57 FR 61834
212.123Visible Emissions Limitations for All Other Emission Units7/13/198812/29/1992, 57 FR 61834
212.124Exceptions7/13/198812/29/1992, 57 FR 61834
212.125Determination of Violations7/13/198812/29/1992, 57 FR 61834
212.126Adjusted Opacity Standards Procedures7/13/198812/29/1992, 57 FR 61834
Subpart D: Particulate Matter Emissions From Incinerators
212.181Limitations for Incinerators6/4/198011/27/1981, 46 FR 57893
212.182Aqueous Waste Incinerators6/4/198011/27/1981, 46 FR 57893
212.183Certain Wood Waste Incinerators6/4/198011/27/1981, 46 FR 57893
212.184Explosive Waste Incinerators6/4/198011/27/1981, 46 FR 57893
212.185Continuous Automatic Stoking Animal Pathological Waste Incinerators12/30/19869/15/1993, 58 FR 48312
Subpart E: Particulate Matter Emissions From Fuel Combustion Emission Units
212.201Emission Units for Which Construction or Modification Commenced Prior to April 14, 1972, Using Solid Fuel Exclusively Located in the Chicago Area7/9/198612/29/1992, 57 FR 61834
212.202Emission Units for Which Construction or Modification Commenced Prior to April 14, 1972, Using Solid Fuel Exclusively Located Outside the Chicago Area7/9/198612/29/1992, 57 FR 61834
212.203Controlled Emission Units for Which Construction or Modification Commenced Prior to April 14, 1972, Using Solid Fuel Exclusively7/9/198612/29/1992, 57 FR 61834
212.204Emission Units for Which Construction or Modification Commenced on or After April 14, 1972, Using Solid Fuel Exclusively7/9/198612/29/1992, 57 FR 61834
212.205Coal-Fired Industrial Boilers for Which Construction or Modification Commenced Prior to April 14, 1972, Equipped With Flue Gas Desulfurization Systems10/19/19812/22/1984, 49 FR 6490
212.206Emission Units Using Liquid Fuel Exclusively4/14/19725/31/1972, 37 FR 10842
212.207Emission Units Using More Than One Type of Fuel4/14/19725/31/1972, 37 FR 10842
212.208Aggregation of Emission Units for Which Construction or Modification Commenced Prior to April 14, 19724/14/19725/31/1972, 37 FR 10842
212.210Emissions Limitations for Certain Fuel Combustion Emission Units Located in the Vicinity of Granite City5/22/19967/14/1999, 64 FR 37847
Subpart K: Fugitive Particulate Matter
212.301Fugitive Particulate Matter10/26/19792/21/1980, 45 FR 11472
212.302Geographical Areas of Application5/22/19967/14/1999, 64 FR 37847
212.304Storage Piles10/26/19794/26/1982, 47 FR 17814
212.305Conveyor Loading Operations10/26/19794/26/1982, 47 FR 17814
212.306Traffic Areas10/26/19792/21/1980, 45 FR 11472
212.307Materials Collected by Pollution Control Equipment10/26/19792/21/1980, 45 FR 11472
212.308Spraying or Choke-Feeding Required10/26/19792/21/1980, 45 FR 11472
212.309Operating Program5/22/19967/14/1999, 64 FR 37847
212.310Minimum Operating Program10/26/19792/21/1980, 45 FR 11472
212.312Amendment to Operating Program10/26/19792/21/1980, 45 FR 11472
212.313Emission Standard for Particulate Collection Equipment10/26/19792/21/1980, 45 FR 11472
212.314Exception for Excess Wind Speed10/26/19792/21/1980, 45 FR 11472
212.315Covering for Vehicles10/26/19792/21/1980, 45 FR 11472
212.316Emissions Limitations for Emission Units in Certain Areas5/22/19967/14/1999, 64 FR 37847
Subpart L: Particulate Matter Emissions From Process Emission Units
212.321Process Emission Units for Which Construction or Modification Commenced on or After April 14, 19729/28/19792/21/1980, 45 FR 11472
212.322Process Emission Units for Which Construction or Modification Commenced Prior to April 14, 19729/28/19792/21/1980, 45 FR 11472
212.323Stock Piles9/28/19792/21/1980, 45 FR 11472
212.324Process Emission Units in Certain Areas5/22/19963/11/1998, 63 FR 11842
Subpart N: Food Manufacturing
212.361Corn Wet Milling Processes9/28/19792/21/1980, 45 FR 11472
212.362Emission Units in Certain Areas5/22/19963/11/1998, 63 FR 11842
Subpart O: Petroleum Refining, Petrochemical and Chemical Manufacturing
212.381Catalyst Regenerators of Fluidized Catalytic Converters9/28/19792/21/1980, 45 FR 11472
Subpart Q: Stone, Clay, Glass and Concrete Manufacturing
212.421Portland Cement Processes for Which Construction or Modification Commenced on or After April 14, 19724/14/19725/31/1972, 37 FR 10842
212.422Portland Cement Manufacturing Processes9/28/19792/21/1980, 45 FR 11472
212.423Emission Limits for the Portland Cement Manufacturing Plant Located in LaSalle County, South of the Illinois River10/4/199110/21/1993, 58 FR 54291
212.424Fugitive Particulate Matter Control for the Portland Cement Manufacturing Plant and Associated Quarry Operations Located in LaSalle County, South of the Illinois River5/15/19921/12/1993, 58 FR 3844
212.425Emission Units in Certain Areas5/22/19963/11/1998, 63 FR 11842
Subpart R: Primary and Fabricated Metal Products and Machinery Manufacture
212.441Steel Manufacturing Processes9/28/19792/21/1980, 45 FR 11472
212.442Beehive Coke Ovens9/28/19792/21/1980, 45 FR 11472
212.443Coke Plants5/15/19921/12/1993, 58 FR 3844
212.444Sinter Processes9/28/19799/3/1981, 46 FR 44172
212.445Blast Furnace Cast Houses5/15/19921/12/1993, 58 FR 3844
212.446Basic Oxygen Furnaces5/22/19963/11/1998, 63 FR 11842
212.447Hot Metal Desulfurization Not Located in the BOF9/28/19799/3/1981, 46 FR 44172
212.448Electric Arc Furnaces9/28/19799/3/1981, 46 FR 44172
212.449Argon-Oxygen Decarburization Vessels9/28/19799/3/1981, 46 FR 44172
212.450Liquid Steel Charging9/28/19799/3/1981, 46 FR 44172
212.451Hot Scarfing Machines9/28/19799/3/1981, 46 FR 44172
212.455Highlines on Steel Mills10/26/19792/21/1980, 45 FR 11472
212.456Certain Small Foundries9/28/19792/21/1980, 45 FR 11472
212.457Certain Small Iron-Melting Air Furnaces9/28/19797/12/1982, 47 FR 30057
212.458Emission Units in Certain Areas5/22/19963/11/1998, 63 FR 11842
Subpart S: Agriculture
212.461Grain-Handling and Drying in General9/28/19792/21/1980, 45 FR 11472
212.462Grain-Handling Operations9/28/19792/21/1980, 45 FR 11472
212.463Grain Drying Operations9/28/19792/21/1980, 45 FR 11472
212.464Sources in Certain Areas5/22/19963/11/1998, 63 FR 11842
Subpart T: Construction and Wood Products
212.681Grinding, Woodworking, Sandblasting and Shotblasting4/14/19725/31/1972, 37 FR 10842
Subpart U: Additional Control Measures
212.700Applicability7/11/19947/13/1995, 60 FR 36060
212.701Contingency Measure Plans, Submittal and Compliance Date7/11/19947/13/1995, 60 FR 36060
212.702Determination of Contributing Sources7/11/19947/13/1995, 60 FR 36060
212.703Contingency Measure Plan Elements7/11/19947/13/1995, 60 FR 36060
212.704Implementation7/11/19947/13/1995, 60 FR 36060
212.705Alternative Implementation7/11/19947/13/1995, 60 FR 36060
212.Appendix C:Past Compliance Dates4/14/19725/31/1972, 37 FR 10842Approved as Rules 202(e), 203(c), 203(d)(3)(A) & (B), 203(d)(5)(L) & (M), 203(d)(8)(J), 203(f)(3) Preamble, 203(f)(3)(F) Preamble, and 203(i).
Part 214: Sulfur Limitations
Subpart A: General Provisions
214.101Measurement Methods12/7/20152/1/2018, 83 FR 4591
214.102Abbreviations and Units12/7/20152/1/2018, 83 FR 4591
214.103Definitions12/7/20152/1/2018, 83 FR 4591
214.104Incorporations by Reference12/7/20152/1/2018, 83 FR 4591
Subpart B: New Fuel Combustion Emission Sources
214.121Large Sources12/7/20152/1/2018, 83 FR 4591
214.122Small Sources12/7/20152/1/2018, 83 FR 4591
Subpart C: Existing Solid Fuel Combustion Emission Sources
214.141Sources Located in Metropolitan Areas3/28/19839/3/1992, 57 FR 40333thru (a).
214.141Sources Located in Metropolitan Areas5/20/19869/2/1992, 57 FR 40126(b), (c), and (d).
214.142Small Sources Located Outside Metropolitan Areas4/14/19725/31/1972, 37 FR 10842Approved as Rule 204(c)(1)(B).
214.143Large Sources Located Outside Metropolitan Areas2/3/19792/21/1980, 45 FR 11472
Subpart D: Existing Liquid or Mixed Fuel Combustion Emission Sources
214.161Liquid Fuel Burned Exclusively12/7/20152/1/2018, 83 FR 4591
214.162Combination of Fuels12/7/20152/1/2018, 83 FR 4591
Subpart E: Aggregation of Sources Outside Metropolitan Areas
214.181Dispersion Enhancement Techniques2/3/19792/21/1980, 45 FR 11472
214.182Prohibition2/3/19792/21/1980, 45 FR 11472Approved as Rule 204(e) (intro).
214.183General Formula2/3/19792/21/1980, 45 FR 11472Approved as Rule 204(e)(1).
214.184Special Formula2/3/19792/21/1980, 45 FR 11472Approved as Rule 204(e)(2).
214.185Alternative Emission Rate2/3/19792/21/1980, 45 FR 11472Approved as Rule 204(e)(3).
214.186New Operating Permits2/3/19792/21/1980, 45 FR 11472Approved as Rule 204(e)(4).
Subpart F: Alternative Standards for Sources Inside Metropolitan Areas
214.201Alternative Standards for Sources in Metropolitan Areas12/7/20152/1/2018, 83 FR 4591
214.202Dispersion Enhancement Techniques3/28/19839/3/1992, 57 FR 40333
Subpart K: Process Emission Sources
214.300Scope12/7/20152/1/2018, 83 FR 4591
214.301General Limitation2/3/19792/21/1980, 45 FR 11472Approved as Rule 204(f)(1)(A).
214.302Exception for Air Pollution Control Equipment4/14/19725/31/1972, 37 FR 10842Approved as Rule 204(f)(1)(C).
214.303Use of Sulfuric Acid2/3/19792/21/1980, 45 FR 11472Approved as Rule 204(f)(2)(B).
214.305Fuel Sulfur Content Limitations12/7/20152/1/2018, 83 FR 4591
Subpart O: Petroleum Refining, Petrochemical and Chemical Manufacturing
214.381Sulfuric Acid Manufacturing2/3/19792/21/1980, 45 FR 11472Only (a) and (b). Approved as Rule 204(f)(1)(B) and (f)(2)(A).
214.382Petroleum and Petrochemical Processes12/5/19881/28/1994, 59 FR 4001
214.383Chemical Manufacturing2/3/19792/21/1980, 45 FR 11472Approved as Rule 204(f)(1)(E).
Subpart Q: Primary and Secondary Metal Manufacturing
214.421Combination of Fuels at Steel Mills in Metropolitan Areas12/7/20152/1/2018, 83 FR 4591
Subpart X: Utilities
214.560Scope5/20/19869/2/1992, 57 FR 40126
214.561E. D. Edwards Electric Generating Station7/11/200311/10/2008, 73 FR 66555
Subpart AA: Requirements for Certain SO2 Sources
214.600Definitions12/7/20152/1/2018, 83 FR 4591
214.601Applicability12/7/20152/1/2018, 83 FR 4591
214.602Compliance Deadline12/7/20152/1/2018, 83 FR 4591
214.603Emission Limitations12/7/20152/1/2018, 83 FR 4591
214.604Monitoring and Testing12/7/20152/1/2018, 83 FR 4591
214.605Recordkeeping and Reporting12/7/20152/1/2018, 83 FR 4591
214.Appendix C:Compliance Dates4/14/19725/31/1972, 37 FR 10842Approved as Rule 204(e)(1).
Part 215: Organic Material Emission Standards and Limitations
Subpart A: General Provisions
215.101Clean-Up and Disposal Operations7/28/19792/21/1980, 45 FR 11472
215.102Testing Methods5/14/19918/18/1992, 57 FR 37100
215.104Definitions1/28/201310/6/2014, 79 FR 60070
215.105Incorporation by Reference1/28/201310/6/2014, 79 FR 60070
215.108Measurement of Vapor Pressures5/14/19918/18/1992, 57 FR 37100
215.109Monitoring for Negligibly-Reactive Compounds6/19/19981/15/1999, 64 FR 2581
Subpart B: Organic Emissions From Storage and Loading Operations
215.121Storage Containers7/28/19792/21/1980, 45 FR 11472
215.122Loading Operations7/28/19792/21/1980, 45 FR 11472
215.123Petroleum Liquid Storage Tanks7/28/19792/21/1980, 45 FR 11472
215.124External Floating Roofs1/21/19836/29/1990, 55 FR 26814
215.125Compliance Dates and Geographical Areas1/21/19836/29/1990, 55 FR 26814
215.126Compliance Plan1/21/19836/29/1990, 55 FR 26814
Subpart C: Organic Emissions From Miscellaneous Equipment
215.141Separation Operations7/28/19792/21/1980, 45 FR 11472
215.142Pumps and Compressors7/28/19792/21/1980, 45 FR 11472
215.143Vapor Blowdown7/28/19792/21/1980, 45 FR 11472
215.144Safety Relief Valves7/28/19792/21/1980, 45 FR 11472
Subpart E: Solvent Cleaning
215.181Solvent Cleaning in General7/28/19792/21/1980, 45 FR 11472
215.182Cold Cleaning7/28/19792/21/1980, 45 FR 11472
215.183Open Top Vapor Degreasing7/28/19792/21/1980, 45 FR 11472
215.184Conveyorized Degreasing7/28/19792/21/1980, 45 FR 11472
Subpart F: Coating Operations
215.202Compliance Schedules7/28/19792/21/1980, 45 FR 11472
215.204Emission Limitations for Manufacturing Plants6/19/19981/15/1999, 64 FR 2581
215.205Alternative Emission Limitations6/19/19981/15/1999, 64 FR 2581
215.206Exemptions From Emission Limitations6/19/19981/15/1999, 64 FR 2581
215.207Compliance by Aggregation of Emission Units6/19/19981/15/1999, 64 FR 2581
215.208Testing Methods for Volatile Organic Material Content7/28/19792/21/1980, 45 FR 11472
215.209Exemption From General Rule on Use of Organic Material7/28/19792/21/1980, 45 FR 11472
215.211Compliance Dates and Geographical Areas6/19/19981/15/1999, 64 FR 2581
215.212Compliance Plan6/19/19981/15/1999, 64 FR 2581
215.213Special Requirements for Compliance Plan7/28/19792/21/1980, 45 FR 11472
215.215DMI Emissions Limitations7/28/19792/21/1980, 45 FR 11472
Subpart H: Special Limitations for Sources in Major Urbanized Areas Which Are Nonattainment for Ozone
215.240Applicability6/29/19876/29/1990, 55 FR 26814
215.241External Floating Roofs6/29/19876/29/1990, 55 FR 26814
215.249Compliance Dates6/29/19876/29/1990, 55 FR 26814
Subpart K: Use of Organic Material
215.301Use of Organic Material7/28/19792/21/1980, 45 FR 11472
215.302Alternative Standard7/28/19792/21/1980, 45 FR 11472
215.303Fuel Combustion Emission Sources7/28/19792/21/1980, 45 FR 11472
215.304Operations With Compliance Program7/28/19792/21/1980, 45 FR 11472
Subpart P: Printing and Publishing
215.408Heatset Web Offset Lithographic Printing9/30/19876/29/1990, 55 FR 26814
Subpart Q: Leaks From Synthetic Organic Chemical and Polymer Manufacturing Equipment
215.420Applicability12/14/19876/29/1990, 55 FR 26814
215.421General Requirements12/14/19876/29/1990, 55 FR 26814
215.422Inspection Program Plan for Leaks8/28/19856/29/1990, 55 FR 26814
215.423Inspection Program for Leaks8/28/19856/29/1990, 55 FR 26814
215.424Repairing Leaks8/28/19856/29/1990, 55 FR 26814
215.425Recordkeeping for Leaks8/28/19856/29/1990, 55 FR 26814
215.426Reporting for Leaks8/28/19856/29/1990, 55 FR 26814
215.427Alternative Program for Leaks8/28/19856/29/1990, 55 FR 26814
215.428Compliance Dates12/14/19876/29/1990, 55 FR 26814
215.429Compliance Plan12/14/19876/29/1990, 55 FR 26814
215.430General Requirements12/14/19876/29/1990, 55 FR 26814
215.431Inspection Program Plan for Leaks12/14/19876/29/1990, 55 FR 26814
215.433Repairing Leaks12/14/19876/29/1990, 55 FR 26814
215.434Recordkeeping for Leaks12/14/19876/29/1990, 55 FR 26814
215.435Report for Leaks12/14/19876/29/1990, 55 FR 26814
215.437Open-Ended Valves12/14/19876/29/1990, 55 FR 26814
215.438Compliance Plan12/14/19876/29/1990, 55 FR 26814
Subpart R: Petroleum Refining and Related Industries; Asphalt Materials
215.441Petroleum Refinery Waste Gas Disposal7/28/19792/21/1980, 45 FR 11472
215.442Vacuum Producing Systems7/28/19792/21/1980, 45 FR 11472
215.443Wastewater (Oil/Water) Separator7/28/19792/21/1980, 45 FR 11472
215.444Process Unit Turnarounds7/28/19792/21/1980, 45 FR 11472
215.445Leaks: General Requirements1/21/198311/27/1987, 52 FR 45333
215.446Monitoring Program Plan for Leaks1/21/198311/27/1987, 52 FR 45333
215.447Monitoring Program for Leaks1/21/198311/27/1987, 52 FR 45333
215.448Recordkeeping for Leaks1/21/198311/27/1987, 52 FR 45333
215.449Reporting for Leaks1/21/198311/27/1987, 52 FR 45333
215.450Alternative Program for Leaks1/21/198311/27/1987, 52 FR 45333
215.451Sealing Device Requirements1/21/198311/27/1987, 52 FR 45333
215.453Compliance Dates and Geographical Areas1/21/19836/29/1990, 55 FR 26814
Subpart S: Rubber and Miscellaneous Plastic Products
215.461Manufacture of Pneumatic Rubber Tires1/21/198311/27/1987, 52 FR 45333
215.462Green Tire Spraying Operations1/21/198311/27/1987, 52 FR 45333
215.463Alternative Emission Reduction Systems1/21/198311/27/1987, 52 FR 45333
215.464Emissions Testing1/21/198311/27/1987, 52 FR 45333
215.465Compliance Dates and Geographical Areas1/21/19836/29/1990, 55 FR 26814
215.466Compliance Plan1/21/19836/29/1990, 55 FR 26814
Subpart T: Pharmaceutical Manufacturing
215.480Applicability of Subpart T5/14/19918/18/1992, 57 FR 37100
215.481Control of Reactors, Distillation Units, Crystallizers, Centrifuges and Vacuum Dryers5/14/19918/18/1992, 57 FR 37100
215.482Control of Air Dryers, Production Equipment Exhaust Systems and Filters5/14/19918/18/1992, 57 FR 37100
215.483Material Storage and Transfer5/14/19918/18/1992, 57 FR 37100
215.484In-Process Tanks5/14/19918/18/1992, 57 FR 37100
215.485Leaks5/14/19918/18/1992, 57 FR 37100
215.486Other Emission Sources5/14/19918/18/1992, 57 FR 37100
215.487Testing5/14/19918/18/1992, 57 FR 37100
215.488Monitors for Air Pollution Control Equipment5/14/19918/18/1992, 57 FR 37100
215.489Recordkeeping (Renumbered)5/14/19918/18/1992, 57 FR 37100
215.490Compliance Schedule (Renumbered)5/14/19918/18/1992, 57 FR 37100
Subpart V: Air Oxidation Processes
215.520Applicability12/14/19876/29/1990, 55 FR 26814
215.521Definitions12/14/19876/29/1990, 55 FR 26814
215.525Emission Limitations for Air Oxidation Processes12/14/19876/29/1990, 55 FR 26814
215.526Testing and Monitoring12/14/19876/29/1990, 55 FR 26814
215.527Compliance Date12/14/19876/29/1990, 55 FR 26814
Subpart W: Agriculture
215.541Pesticide Exception7/28/19792/21/1980, 45 FR 11472
Subpart X: Construction
215.561Architectural Coatings7/28/19792/21/1980, 45 FR 11472
215.562Paving Operations7/28/19792/21/1980, 45 FR 11472
215.563Cutback Asphalt7/28/19792/21/1980, 45 FR 11472
Subpart Y: Gasoline Distribution
215.581Bulk Gasoline Plants7/28/19792/21/1980, 45 FR 11472
215.582Bulk Gasoline Terminals6/29/19876/29/1990, 55 FR 26814
215.583Gasoline Dispensing Facilities—Storage Tank Filling Operations6/29/19876/29/1990, 55 FR 26814
215.584Gasoline Delivery Vessels6/29/19876/29/1990, 55 FR 26814
Subpart Z: Dry Cleaners
215.607Standards for Petroleum Solvent Dry Cleaners4/3/19876/29/1990, 55 FR 26814
215.608Operating Practices for Petroleum Solvent Dry Cleaners4/3/19876/29/1990, 55 FR 26814
215.609Program for Inspection and Repair of Leaks4/3/19876/29/1990, 55 FR 26814
215.610Testing and Monitoring4/3/19876/29/1990, 55 FR 26814
215.611Exemption for Petroleum Solvent Dry Cleaners4/3/19876/29/1990, 55 FR 26814
215.612Compliance Dates and Geographical Areas4/3/19876/29/1990, 55 FR 26814
215.613Compliance Plan4/3/19876/29/1990, 55 FR 26814
Subpart BB: Polystyrene Plants
215.875Applicability of Subpart BB9/30/19876/29/1990, 55 FR 26814
215.877Emissions Limitation at Polystyrene Plants9/30/19876/29/1990, 55 FR 26814
215.879Compliance Date9/30/19876/29/1990, 55 FR 26814
215.881Compliance Plan9/30/19876/29/1990, 55 FR 26814
215.883Special Requirements for Compliance Plan9/30/19876/29/1990, 55 FR 26814
215.886Emissions Testing9/30/19876/29/1990, 55 FR 26814
215.Appendix C:Past Compliance Dates7/28/19792/21/1980, 45 FR 11472Approved as Rules 104(a), 104(g), 104(h), 205(j), and 205(m).
Part 216: Carbon Monoxide Emissions
Subpart A: General Provisions
216.101Measurement Methods7/28/19792/21/1980, 45 FR 11472Approved as Rule 206(f).
Subpart B: Fuel Combustion Emission Sources
216.121Fuel Combustion Emission Sources7/28/19792/21/1980, 45 FR 11472Approved as Rule 206(a).
Subpart C: Incinerators
216.141Incinerators7/28/19792/21/1980, 45 FR 11472Approved as Rule 206(b).
216.142Exceptions7/28/19792/21/1980, 45 FR 11472Approved as Rule 206(b)(1,2).
Subpart N: Petroleum Refining and Chemical Manufacture
216.361Petroleum and Petrochemical Processes7/28/19792/21/1980, 45 FR 11472Approved as Rule 206(c).
216.362Polybasic Organic Acid Partial Oxidation Manufacturing Processes7/28/19792/21/1980, 45 FR 11472Approved as Rule 206(h).
Subpart O: Primary and Fabricated Metal Products
216.381Cupolas7/28/19792/21/1980, 45 FR 11472Approved as Rule 206(e).
216.382Exception, General Motor's Ferrous Foundry in Vermilion County11/13/19928/4/1994, 59 FR 39686
216.Appendix C:Compliance Dates7/28/19792/21/1980, 45 FR 11472Approved as Rule 206(g).
Part 217: Nitrogen Oxides Emissions
Subpart A: General Provisions
217.101Measurement Methods9/25/20076/26/2009, 74 FR 30466
217.102Abbreviations and Units9/25/20076/26/2009, 74 FR 30466
217.104Incorporations by Reference9/25/20076/26/2009, 74 FR 30466
Subpart B: New Fuel Combustion Emission Sources
217.121New Emission Sources4/14/19725/31/1972, 37 FR 10862Approved as Rule 207(a)(1)-(4), 207(a)(5)(A).
Subpart C: Existing Fuel Combustion Emission Sources
217.141Existing Emission Sources in Major Metropolitan Areas4/14/19725/31/1972, 37 FR 10862Approved as Rule 207(b) and (c).
Subpart K: Process Emission Sources
217.301Industrial Processes4/14/19725/31/1972, 37 FR 10862Approved as Rule 207(e).
Subpart O: Chemical Manufacture
217.381Nitric Acid Manufacturing Processes4/14/19725/31/1972, 37 FR 10862Approved as Rule 207(d).
Subpart Q: Stationary Reciprocating Internal Combustion Engines and Turbines
217.386Applicability9/25/20076/26/2009, 74 FR 30466
217.388Control and Maintenance Requirements9/25/20076/26/2009, 74 FR 30466
217.390Emissions Averaging Plans9/25/20076/26/2009, 74 FR 30466
217.392Compliance9/25/20076/26/2009, 74 FR 30466
217.394Testing and Monitoring9/25/20076/26/2009, 74 FR 30466
217.396Recordkeeping and Reporting9/25/20076/26/2009, 74 FR 30466
Subpart T: Cement Kilns
217.400Applicability3/15/200111/8/2001, 66 FR 56449
217.402Control Requirements3/15/200111/8/2001, 66 FR 56449
217.404Testing3/15/200111/8/2001, 66 FR 56449
217.406Monitoring3/15/200111/8/2001, 66 FR 56449
217.408Reporting3/15/200111/8/2001, 66 FR 56449
217.410Recordkeeping3/15/200111/8/2001, 66 FR 56449
Subpart U: NOX Control and Trading Program for Specified NOX Generating Units
217.450Purpose4/17/200111/8/2001, 66 FR 56449
217.452Severability4/17/200111/8/2001, 66 FR 56449
217.454Applicability4/17/200111/8/2001, 66 FR 56449
217.456Compliance Requirements4/17/200111/8/2001, 66 FR 56449
217.458Permitting Requirements4/17/200111/8/2001, 66 FR 56449
217.460Subpart U NOX Trading Budget4/17/200111/8/2001, 66 FR 56449
217.462Methodology for Obtaining NOX Allocations4/17/200111/8/2001, 66 FR 56449
217.464Methodology for Determining NOX Allowances From the New Source Set-Aside4/17/200111/8/2001, 66 FR 56449
217.466NOX Allocations Procedure for Subpart U Budget Units4/17/200111/8/2001, 66 FR 56449
217.468New Source Set-Asides for “New” Budget Units4/17/200111/8/2001, 66 FR 56449
217.470Early Reduction Credits (ERCS) for Budget Units4/17/200111/8/2001, 66 FR 56449
217.472Low-Emitter Requirements4/17/200111/8/2001, 66 FR 56449
217.474Opt-In Units4/17/200111/8/2001, 66 FR 56449
217.476Opt-In Process4/17/200111/8/2001, 66 FR 56449
217.478Opt-In Budget Units: Withdrawal From NOX Trading Program4/17/200111/8/2001, 66 FR 56449
217.480Opt-In Units: Change in Regulatory Status4/17/200111/8/2001, 66 FR 56449
217.482Allowance Allocations To Opt-In Budget Units4/17/200111/8/2001, 66 FR 56449
Subpart V: Electric Power Generation
217.521Lake of Egypt Power Plant4/13/19786/18/2001, 66 FR 32769
217.700Purpose4/17/20016/18/2001, 66 FR 32769
217.702Severability4/17/20016/18/2001, 66 FR 32769
217.704Applicability4/17/20016/18/2001, 66 FR 32769
217.706Emission Limitations4/17/20016/18/2001, 66 FR 32769
217.708NOX Averaging4/17/20016/18/2001, 66 FR 32769
217.710Monitoring4/17/20016/18/2001, 66 FR 32769
217.712Reporting and Recordkeeping4/17/20016/18/2001, 66 FR 32769
Subpart W: NOX Trading Program for Electrical Generating Units
217.750Purpose12/26/200011/8/2001, 66 FR 56454
217.751Sunset Provisions11/2/20093/1/2010, 75 FR 9103
217.752Severability12/26/200011/8/2001, 66 FR 56454
217.754Applicability12/26/200011/8/2001, 66 FR 56454
217.756Compliance Requirements12/26/200011/8/2001, 66 FR 56454Except (d)(3).
217.758Permitting Requirements12/26/200011/8/2001, 66 FR 56454
217.760NOx Trading Budget12/26/200011/8/2001, 66 FR 56454
217.762Methodology for Calculating NOX Allocations for Budget Electrical Generating Units (EGUs)12/26/200011/8/2001, 66 FR 56454
217.764NOX Allocations for Budget EGUs12/26/200011/8/2001, 66 FR 56454
217.768New Source Set-Asides for “New” Budget EGUs12/26/200011/8/2001, 66 FR 56454
217.770Early Reduction Credits for Budget EGUs12/26/200011/8/2001, 66 FR 56454
217.774Opt-In Units12/26/200011/8/2001, 66 FR 56454
217.776Opt-In Process12/26/200011/8/2001, 66 FR 56454
217.778Budget Opt-In Units: Withdrawal From NOX Trading Program12/26/200011/8/2001, 66 FR 56454
217.780Opt-In Units: Change in Regulatory Status12/26/200011/8/2001, 66 FR 56454
217.782Allowance Allocations to Budget Opt-In Units12/26/200011/8/2001, 66 FR 56454
217.Appendix C:Compliance Dates4/14/19725/31/1972, 37 FR 10862
217.Appendix G:Existing Reciprocating Internal Combustion Engines Affected by the NOX Sip Call9/25/20076/26/2009, 74 FR 30466
Part 218: Organic Material Emission Standards and Limitations for the Chicago Area
Subpart A: General Provisions
218.100Introduction9/27/19939/9/1994, 59 FR 46562
218.101Savings Clause10/25/19944/3/1995, 60 FR 16801
218.102Abbreviations and Conversion Factors9/27/19939/9/1994, 59 FR 46562
218.103Applicability9/27/19939/9/1994, 59 FR 46562
218.104Definitions9/27/19939/9/1994, 59 FR 46562
218.105Test Methods and Procedures7/27/20113/23/2012, 77 FR 16940
218.106Compliance Dates9/14/20103/23/2012, 77 FR 16940
218.107Operation of Afterburners9/27/19939/9/1994, 59 FR 46562
218.108Exemptions, Variations, and Alternative Means of Control or Compliance Determinations1/24/199410/21/1996, 61 FR 54556
218.109Vapor Pressure of Volatile Organic Liquids9/27/19939/9/1994, 59 FR 46562
218.110Vapor Pressure of Organic Material or Solvent9/27/19939/9/1994, 59 FR 46562
218.111Vapor Pressure of Volatile Organic Material9/27/19939/9/1994, 59 FR 46562
218.112Incorporations by Reference12/23/20133/13/2015, 80 FR 13248
218.114Compliance With Permit Conditions1/24/199410/21/1996, 61 FR 54556
Subpart B: Organic Emissions From Storage and Loading Operations
218.119Applicability for VOL11/15/19948/8/1996, 61 FR 41338
218.120Control Requirements for Storage Containers of VOL11/15/19948/8/1996, 61 FR 41338
218.121Storage Containers9/27/19939/9/1994, 59 FR 46562
218.122Loading Operations9/27/19939/9/1994, 59 FR 46562
218.123Petroleum Liquid Storage Tanks9/27/19939/9/1994, 59 FR 46562
218.124External Floating Roofs9/27/19939/9/1994, 59 FR 46562
218.125Compliance Dates11/15/19948/8/1996, 61 FR 41338
218.127Testing VOL Operations11/15/19948/8/1996, 61 FR 41338
218.128Monitoring VOL Operations1/28/201310/6/2014, 79 FR 60070
218.129Recordkeeping and Reporting for VOL Operations11/15/19948/8/1996, 61 FR 41338
Subpart C: Organic Emissions From Miscellaneous Equipment
218.141Separation Operations9/27/19939/9/1994, 59 FR 46562
218.142Pumps and Compressors8/16/19919/9/1994, 59 FR 46562
218.143Vapor Blowdown9/27/19939/9/1994, 59 FR 46562
218.144Safety Relief Valves9/27/19939/9/1994, 59 FR 46562
Subpart E: Solvent Cleaning
218.181Solvent Cleaning Degreasing Operations6/25/20103/23/2012, 77 FR 16940
218.182Cold Cleaning6/9/199711/26/1997, 62 FR 62951
218.183Open Top Vapor Degreasing9/27/19939/9/1994, 59 FR 46562
218.184Conveyorized Degreasing9/27/19939/9/1994, 59 FR 46562
218.186Test Methods9/27/19939/9/1994, 59 FR 46562
218.187Other Industrial Solvent Cleaning Operations7/27/20113/23/2012, 77 FR 16940
Subpart F: Coating Operations
218.204Emission Limitations7/27/20113/23/2012, 77 FR 16940
218.205Daily-Weighted Average Limitations9/14/20103/23/2012, 77 FR 16940
218.206Solids Basis Calculation9/27/19939/9/1994, 59 FR 46562
218.207Alternative Emission Limitations7/27/20113/23/2012, 77 FR 16940
218.208Exemptions From Emission Limitations10/25/20114/19/2013, 78 FR 23495
218.209Exemption From General Rule on Use of Organic Material9/27/19939/9/1994, 59 FR 46562
218.210Compliance Schedule6/25/20103/23/2012, 77 FR 16940
218.211Recordkeeping and Reporting7/27/20113/23/2012, 77 FR 16940
218.212Cross-Line Averaging To Establish Compliance for Coating Lines9/14/20103/23/2012, 77 FR 16940
218.213Recordkeeping and Reporting for Cross-Line Averaging Participating Coating Lines5/9/19952/13/1996, 61 FR 5511
218.214Changing Compliance Methods5/9/19952/13/1996, 61 FR 5511
218.215Wood Furniture Coating Averaging Approach2/2/19985/19/1998, 63 FR 27489
218.216Wood Furniture Coating Add-On Control Use2/2/19985/19/1998, 63 FR 27489
218.217Wood Furniture Coating and Flat Wood Paneling Coating Work Practice Standards7/27/20113/23/2012, 77 FR 16940
218.218Work Practice Standards for Paper Coatings, Metal Furniture Coatings, and Large Appliance Coatings3/23/20103/23/2012, 77 FR 16940
218.219Work Practice Standards for Automobile and Light-Duty Truck Assembly Coatings and Miscellaneous Metal and Plastic Parts Coatings9/14/20103/23/2012, 77 FR 16940
Subpart G: Use of Organic Material
218.301Use of Organic Material9/27/19939/9/1994, 59 FR 46562
218.302Alternative Standard9/27/19939/9/1994, 59 FR 46562
218.303Fuel Combustion Emission Units9/27/19939/9/1994, 59 FR 46562
218.304Operations With Compliance Program9/27/19939/9/1994, 59 FR 46562
Subpart H: Printing and Publishing
218.401Flexographic and Rotogravure Printing7/27/20113/23/2012, 77 FR 16940
218.402Applicability7/27/20113/23/2012, 77 FR 16940
218.403Compliance Schedule6/25/20103/23/2012, 77 FR 16940
218.404Recordkeeping and Reporting7/27/20113/23/2012, 77 FR 16940
218.405Lithographic Printing: Applicability6/25/20103/23/2012, 77 FR 16940
218.407Emission Limitations and Control Requirements for Lithographic Printing Lines6/25/20103/23/2012, 77 FR 16940
218.409Testing for Lithographic Printing on and After March 15, 19967/27/20113/23/2012, 77 FR 16940
218.410Monitoring Requirements for Lithographic Printing6/25/20103/23/2012, 77 FR 16940
218.411Recordkeeping and Reporting for Lithographic Printing7/27/20113/23/2012, 77 FR 16940
218.412Letterpress Printing Lines: Applicability6/25/20103/23/2012, 77 FR 16940
218.413Emission Limitations and Control Requirements for Letterpress Printing Lines6/25/20103/23/2012, 77 FR 16940
218.415Testing for Letterpress Printing Lines7/27/20113/23/2012, 77 FR 16940
218.416Monitoring Requirements for Letterpress Printing Lines6/25/20103/23/2012, 77 FR 16940
218.417Recordkeeping and Reporting for Letterpress Printing Lines7/27/20113/23/2012, 77 FR 16940
Subpart Q: Synthetic Organic Chemical and Polymer Manufacturing Plant
218.421General Requirements9/27/19939/9/1994, 59 FR 46562
218.422Inspection Program Plan for Leaks9/27/19939/9/1994, 59 FR 46562
218.423Inspection Program for Leaks9/27/19939/9/1994, 59 FR 46562
218.424Repairing Leaks9/27/19939/9/1994, 59 FR 46562
218.425Recordkeeping for Leaks9/27/19939/9/1994, 59 FR 46562
218.426Report for Leaks9/27/19939/9/1994, 59 FR 46562
218.427Alternative Program for Leaks9/27/19939/9/1994, 59 FR 46562
218.428Open-Ended Valves9/27/19939/9/1994, 59 FR 46562
218.429Standards for Control Devices9/27/19939/9/1994, 59 FR 46562
218.431Applicability5/9/19953/23/1998, 63 FR 13784
218.432Control Requirements5/9/19953/23/1998, 63 FR 13784
218.433Performance and Testing Requirements5/9/19953/23/1998, 63 FR 13784
218.434Monitoring Requirements5/9/19953/23/1998, 63 FR 13784
218.435Recordkeeping and Reporting Requirements5/9/19953/23/1998, 63 FR 13784
218.436Compliance Date5/9/19953/23/1998, 63 FR 13784
Subpart R: Petroleum Refining and Related Industries; Asphalt Materials
218.441Petroleum Refinery Waste Gas Disposal9/27/19939/9/1994, 59 FR 46562
218.442Vacuum Producing Systems8/16/19919/9/1994, 59 FR 46562
218.443Wastewater (Oil/Water) Separator9/27/19939/9/1994, 59 FR 46562
218.444Process Unit Turnarounds8/16/19919/9/1994, 59 FR 46562
218.445Leaks: General Requirements9/27/19939/9/1994, 59 FR 46562
218.446Monitoring Program Plan for Leaks9/27/19939/9/1994, 59 FR 46562
218.447Monitoring Program for Leaks9/27/19939/9/1994, 59 FR 46562
218.448Recordkeeping for Leaks8/16/19919/9/1994, 59 FR 46562
218.449Reporting for Leaks9/27/19939/9/1994, 59 FR 46562
218.450Alternative Program for Leaks9/27/19939/9/1994, 59 FR 46562
218.451Sealing Device Requirements8/16/19919/9/1994, 59 FR 46562
218.452Compliance Schedule for Leaks9/27/19939/9/1994, 59 FR 46562
Subpart S: Rubber and Miscellaneous Plastic Products
218.461Manufacture of Pneumatic Rubber Tires9/27/19939/9/1994, 59 FR 46562
218.462Green Tire Spraying Operations9/27/19939/9/1994, 59 FR 46562
218.463Alternative Emission Reduction Systems9/27/19939/9/1994, 59 FR 46562
218.464Emission Testing9/27/19939/9/1994, 59 FR 46562
Subpart T: Pharmaceutical Manufacturing
218.480Applicability8/26/200811/3/2010, 75 FR 67623
218.481Control of Reactors, Distillation Units, Crystallizers, Centrifuges and Vacuum Dryers9/27/19939/9/1994, 59 FR 46562
218.482Control of Air Dryers, Production Equipment Exhaust Systems and Filters9/27/19939/9/1994, 59 FR 46562
218.483Material Storage and Transfer9/27/19939/9/1994, 59 FR 46562
218.484In-Process Tanks8/16/19919/9/1994, 59 FR 46562
218.485Leaks9/27/19939/9/1994, 59 FR 46562
218.486Other Emission Units9/27/19939/9/1994, 59 FR 46562
218.487Testing9/27/19939/9/1994, 59 FR 46562
218.488Monitoring for Air Pollution Control Equipment8/16/19919/9/1994, 59 FR 46562
218.489Recordkeeping for Air Pollution Control Equipment9/27/19939/9/1994, 59 FR 46562
Subpart V: Batch Operations and Air Oxidation Processes
218.500Applicability for Batch Operations5/22/19954/2/1996, 61 FR 14484
218.501Control Requirements for Batch Operations5/22/19954/2/1996, 61 FR 14484
218.502Determination of Uncontrolled Total Annual Mass Emissions and Average Flow Rate Values for Batch Operations5/22/19954/2/1996, 61 FR 14484
218.503Performance and Testing Requirements for Batch Operations5/22/19954/2/1996, 61 FR 14484
218.504Monitoring Requirements for Batch Operations5/22/19954/2/1996, 61 FR 14484
218.505Reporting and Recordkeeping for Batch Operations5/22/19954/2/1996, 61 FR 14484
218.506Compliance Date5/22/19954/2/1996, 61 FR 14484
218.520Emission Limitations for Air Oxidation Processes11/15/19949/27/1995, 60 FR 49770
218.522Savings Clause11/15/19949/27/1995, 60 FR 49770
218.523Compliance11/15/19949/27/1995, 60 FR 49770
218.524Determination of Applicability11/15/19949/27/1995, 60 FR 49770
218.525Emission Limitations for Air Oxidation Processes11/15/19949/27/1995, 60 FR 49770
218.526Testing and Monitoring8/16/19919/9/1994, 59 FR 46562
Subpart W: Agriculture
218.541Pesticide Exception9/27/19939/9/1994, 59 FR 46562
Subpart X: Construction
218.561Architectural Coatings8/16/19919/9/1994, 59 FR 46562
218.562Paving Operations9/27/19939/9/1994, 59 FR 46562
218.563Cutback Asphalt8/16/19919/9/1994, 59 FR 46562
Subpart Y: Gasoline Distribution
218.581Bulk Gasoline Plants9/27/19939/9/1994, 59 FR 46562
218.582Bulk Gasoline Terminals9/27/19939/9/1994, 59 FR 46562
218.583Gasoline Dispensing Operations—Storage Tank Filling Operations12/23/20133/13/2015, 80 FR 13248
218.584Gasoline Delivery Vessels9/27/19939/9/1994, 59 FR 46562
218.586Gasoline Dispensing Operations—Motor Vehicle Fueling Operations12/23/20133/13/2015, 80 FR 13248
Subpart Z: Dry Cleaners
218.607Standards for Petroleum Solvent Dry Cleaners8/16/19919/9/1994, 59 FR 46562
218.608Operating Practices for Petroleum Solvent Dry Cleaners9/27/19939/9/1994, 59 FR 46562
218.609Program for Inspection and Repair of Leaks9/27/19939/9/1994, 59 FR 46562
218.610Testing and Monitoring9/27/19939/9/1994, 59 FR 46562
218.611Applicability for Petroleum Solvent Dry Cleaners1/24/199410/21/1996, 61 FR 54556
Subpart AA: Paint and Ink Manufacturing
218.620Applicability1/24/199410/21/1996, 61 FR 54556
218.621Exemption for Waterbase Material and Heatset Offset Ink9/27/19939/9/1994, 59 FR 46562
218.624Open Top Mills, Tanks, Vats or Vessels9/27/19939/9/1994, 59 FR 46562
218.625Grinding Mills8/16/19919/9/1994, 59 FR 46562
218.626Storage Tanks8/16/19919/9/1994, 59 FR 46562
218.628Leaks9/27/19939/9/1994, 59 FR 46562
218.630Clean Up8/16/19919/9/1994, 59 FR 46562
218.636Compliance Schedule9/27/19939/9/1994, 59 FR 46562
218.637Recordkeeping and Reporting9/27/19939/9/1994, 59 FR 46562
Subpart BB: Polystyrene Plants
218.640Applicability9/27/19939/9/1994, 59 FR 46562
218.642Emissions Limitation at Polystyrene Plants9/27/19939/9/1994, 59 FR 46562
218.644Emissions Testing9/27/19939/9/1994, 59 FR 46562
Subpart CC: Polyester Resin Product Manufacturing Process
218.660Applicability1/24/199410/21/1996, 61 FR 54556
218.666Control Requirements1/24/199410/21/1996, 61 FR 54556
218.667Compliance Schedule1/24/199410/21/1996, 61 FR 54556
218.668Testing1/24/199410/21/1996, 61 FR 54556
218.670Recordkeeping and Reporting for Exempt Emission Units1/24/199410/21/1996, 61 FR 54556
218.672Recordkeeping and Reporting for Subject Emission Units1/24/199410/21/1996, 61 FR 54556
Subpart DD: Aerosol Can Fillings
218.680Applicability1/24/199410/21/1996, 61 FR 54556
218.686Control Requirements5/9/19953/12/1997, 62 FR 11327
218.688Testing1/24/199410/21/1996, 61 FR 54556
218.690Recordkeeping and Reporting for Exempt Emission Units1/24/199410/21/1996, 61 FR 54556
218.692Recordkeeping and Reporting for Subject Emission Units1/24/199410/21/1996, 61 FR 54556
Subpart GG: Marine Terminals
218.760Applicability10/25/19944/3/1995, 60 FR 16801
218.762Control Requirements10/25/19944/3/1995, 60 FR 16801
218.764Compliance Certification10/25/19944/3/1995, 60 FR 16801
218.766Leaks10/25/19944/3/1995, 60 FR 16801
218.768Testing and Monitoring10/25/19944/3/1995, 60 FR 16801
218.770Recordkeeping and Reporting10/25/19944/3/1995, 60 FR 16801
Subpart HH: Motor Vehicle Refinishing
218.780Emission Limitations5/9/19957/25/1996, 61 FR 38577
218.782Alternative Control Requirements5/9/19957/25/1996, 61 FR 38577
218.784Equipment Specifications1/28/201310/6/2014, 79 FR 60070
218.786Surface Preparation Materials5/9/19957/25/1996, 61 FR 38577
218.787Work Practices5/9/19957/25/1996, 61 FR 38577
218.788Testing5/9/19957/25/1996, 61 FR 38577
218.789Monitoring and Recordkeeping for Control Devices5/9/19957/25/1996, 61 FR 38577
218.790General Recordkeeping and Reporting5/9/19957/25/1996, 61 FR 38577
218.791Compliance Date5/9/19957/25/1996, 61 FR 38577
Subpart II: Fiberglass Boat Manufacturing Materials
218.890Applicability9/14/20103/23/2012, 77 FR 16940
218.891Emission Limitations and Control Requirements7/27/113/23/12, 77 FR 16940
218.892Testing Requirements7/27/20113/23/2012, 77 FR 16940
218.894Recordkeeping and Reporting Requirements7/27/20113/23/2012, 77 FR 16940
Subpart JJ: Miscellaneous Industrial Adhesives
218.900Applicability9/14/20103/23/2012, 77 FR 16940
218.901Emission Limitations and Control Requirements7/27/20113/23/2012, 77 FR 16940
218.902Testing Requirements7/27/20113/23/2012, 77 FR 16940
218.903Monitoring Requirements7/27/20113/23/2012, 77 FR 16940
218.904Recordkeeping and Reporting Requirements7/27/20113/23/2012, 77 FR 16940
Subpart PP: Miscellaneous Fabricated Product Manufacturing Processes
218.920Applicability1/24/199410/21/1996, 61 FR 54556
218.926Control Requirements1/24/199410/21/1996, 61 FR 54556
218.927Compliance Schedule9/27/199310/21/1996, 61 FR 54556
218.928Testing9/27/199310/21/1996, 61 FR 54556
218.929Cementable and Dress or Performance Shoe Leather4/8/20035/24/2004, 69 FR 29446
Subpart QQ: Miscellaneous Formulation Manufacturing Processes
218.940Applicability7/16/19986/18/1999, 64 FR 32810
218.946Control Requirements1/24/199410/21/1996, 61 FR 54556
218.947Compliance Schedule9/27/19939/9/1994, 59 FR 46562
218.948Testing9/27/19939/9/1994, 59 FR 46562
Subpart RR: Miscellaneous Organic Chemical Manufacturing Processes
218.960Applicability1/24/199410/21/1996, 61 FR 54556
218.966Control Requirements5/9/19953/12/1997, 62 FR 11327
218.967Compliance Schedule9/27/199310/21/1996, 61 FR 54556
218.968Testing9/27/199310/21/1996, 61 FR 54556
Subpart TT: Other Emission Units
218.980Applicability5/9/19953/12/1997, 62 FR 11327
218.986Control Requirements1/24/199410/21/1996, 61 FR 54556
218.987Compliance Schedule9/27/199310/21/1996, 61 FR 54556
218.988Testing9/27/199310/21/1996, 61 FR 54556
Subpart UU: Recordkeeping and Reporting
218.990Exempt Emission Units9/27/199310/21/1996, 61 FR 54556
218.991Subject Emission Units1/24/199410/21/1996, 61 FR 54556
218.Appendix A:List of Chemicals Defining Synthetic Organic Chemical and Polymer Manufacturing9/27/19939/9/1994, 59 FR 46562
218.Appendix B:VOM Measurement Techniques for Capture Efficiency9/27/19939/9/1994, 59 FR 46562
218.Appendix C:Reference Test Methods for Air Oxidation Processes9/27/19939/9/1994, 59 FR 46562
218.Appendix D:Coefficients for the Total Resource Effectiveness Index (TRE) Equation9/27/19939/9/1994, 59 FR 46562
218.Appendix E:List of Affected Marine Terminals10/25/19944/3/1995, 60 FR 16801
218.Appendix G:TRE Index Measurements for SOCMI Reactors and Distillation Units5/9/19953/23/1998, 63 FR 13784
218.Appendix H:Baseline VOM Content Limitations for Subpart F, Section 218.212 Cross-Line Averaging5/9/19952/13/1996, 61 FR 5511
Part 219: Organic Material Emission Standards and Limitations for the Metro East Area
Subpart A: General Provisions
219.100Introduction9/27/19939/9/1994, 59 FR 46562
219.101Savings Clause10/25/19944/3/1995, 60 FR 16801
219.102Abbreviations and Conversion Factors9/27/19939/9/1994, 59 FR 46562
219.103Applicability8/16/19919/9/1994, 59 FR 46562
219.104Definitions9/27/19939/9/1994, 59 FR 46562
219.105Test Methods and Procedures12/23/20133/13/2015, 80 FR 13248
219.106Compliance Dates9/14/20103/23/2012, 77 FR 16940
219.107Operation of Afterburners9/27/19939/9/1994, 59 FR 46562
219.108Exemptions, Variations, and Alternative Means of Control or Compliance Determinations8/16/19919/9/1994, 59 FR 46562
219.109Vapor Pressure of Volatile Organic Liquids9/27/19939/9/1994, 59 FR 46562
219.110Vapor Pressure of Organic Material or Solvent9/27/19939/9/1994, 59 FR 46562
219.111Vapor Pressure of Volatile Organic Material9/27/19939/9/1994, 59 FR 46562
219.112Incorporations by Reference12/23/20133/13/2015, 80 FR 13248
Subpart B: Organic Emissions From Storage and Loading Operations
219.119Applicability for VOL11/15/19948/8/1996, 61 FR 41338
219.120Control Requirements for Storage Containers of VOL11/15/19948/8/1996, 61 FR 41338
219.121Storage Containers of VPL9/27/19939/9/1994, 59 FR 46562
219.122Loading Operations9/27/19939/9/1994, 59 FR 46562
219.123Petroleum Liquid Storage Tanks9/27/19939/9/1994, 59 FR 46562
219.124External Floating Roofs9/27/19939/9/1994, 59 FR 46562
219.125Compliance Dates11/15/19948/8/1996, 61 FR 41338
219.127Testing VOL Operations11/15/19948/8/1996, 61 FR 41338
219.128Monitoring VOL Operations1/28/201310/6/2014, 79 FR 60070
219.129Recordkeeping and Reporting for VOL Operations11/15/19948/8/1996, 61 FR 41338
Subpart C: Organic Emissions From Miscellaneous Equipment
219.141Separation Operations9/27/19939/9/1994, 59 FR 46562
219.142Pumps and Compressors8/16/19919/9/1994, 59 FR 46562
219.143Vapor Blowdown9/27/19939/9/1994, 59 FR 46562
219.144Safety Relief Valves9/27/19939/9/1994, 59 FR 46562
Subpart E: Solvent Cleaning
219.181Solvent Cleaning Degreasing Operations6/25/20103/23/2012, 77 FR 16940
219.182Cold Cleaning6/9/199711/26/1997, 62 FR 62951
219.183Open Top Vapor Degreasing9/27/19939/9/1994, 59 FR 46562
219.184Conveyorized Degreasing9/27/19939/9/1994, 59 FR 46562
219.186Test Methods9/27/19939/9/1994, 59 FR 46562
219.187Other Industrial Solvent Cleaning Operations7/27/20113/23/2012, 77 FR 16940
Subpart F: Coating Operations
219.204Emission Limitations7/27/20113/23/2012, 77 FR 16940
219.205Daily-Weighted Average Limitations9/14/20103/23/2012, 77 FR 16940
219.206Solids Basis Calculation9/27/19939/9/1994, 59 FR 46562
219.207Alternative Emission Limitations7/27/20113/23/2012, 77 FR 16940
219.208Exemptions From Emission Limitations10/25/20114/19/2013, 78 FR 23495
219.209Exemption From General Rule on Use of Organic Material9/27/19939/9/1994, 59 FR 46562
219.210Compliance Schedule9/14/20103/23/2012, 77 FR 16940
219.211Recordkeeping and Reporting7/27/20113/23/2012, 77 FR 16940
219.212Cross-Line Averaging To Establish Compliance for Coating Lines9/14/20103/23/2012, 77 FR 16940
219.213Recordkeeping and Reporting for Cross-Line Averaging Participating Coating Lines5/9/19952/13/1996, 61 FR 5511
219.214Changing Compliance Methods5/9/19952/13/1996, 61 FR 5511
219.215Wood Furniture Coating Averaging Approach2/2/19985/19/1998, 63 FR 27489
219.216Wood Furniture Coating Add-On Control Use2/2/19985/19/1998, 63 FR 27489
219.217Wood Furniture Coating and Flat Wood Paneling Coating Work Practice Standards7/27/20113/23/2012, 77 FR 16940
219.218Work Practice Standards for Paper Coatings, Metal Furniture Coatings, and Large Appliance Coatings3/23/20103/23/2012, 77 FR 16940
219.219Work Practice Standards for Automobile and Light-Duty Truck Assembly Coatings and Miscellaneous Metal and Plastic Parts Coatings9/14/20103/23/2012, 77 FR 16940
Subpart G: Use of Organic Material
219.301Use of Organic Material9/27/19939/9/1994, 59 FR 46562
219.302Alternative Standard9/27/19939/9/1994, 59 FR 46562
219.303Fuel Combustion Emission Units9/27/19939/9/1994, 59 FR 46562
219.304Operations With Compliance Program9/27/19939/9/1994, 59 FR 46562
Subpart H: Printing and Publishing
219.401Flexographic and Rotogravure Printing7/27/20113/23/2012, 77 FR 16940
219.402Applicability6/25/20103/23/2012, 77 FR 16940
219.403Compliance Schedule6/25/20103/23/2012, 77 FR 16940
219.404Recordkeeping and Reporting7/27/20113/23/2012, 77 FR 16940
219.405Lithographic Printing: Applicability6/25/20103/23/2012, 77 FR 16940
219.407Emission Limitations and Control Requirements for Lithographic Printing Lines6/25/20103/23/2012, 77 FR 16940
219.409Testing for Lithographic Printing7/27/20113/23/2012, 77 FR 16940
219.410Monitoring Requirements for Lithographic Printing6/25/20103/23/2012, 77 FR 16940
219.411Recordkeeping and Reporting for Lithographic Printing7/27/20113/23/2012, 77 FR 16940
219.412Letterpress Printing Lines: Applicability6/25/20103/23/2012, 77 FR 16940
219.413Emission Limitations and Control Requirements for Letterpress Printing Lines6/25/20103/23/2012, 77 FR 16940
219.415Testing for Letterpress Printing Lines7/27/20113/23/2012, 77 FR 16940
219.416Monitoring Requirements for Letterpress Printing Lines6/25/20103/23/2012, 77 FR 16940
219.417Recordkeeping and Reporting for Letterpress Printing Lines7/27/20113/23/2012, 77 FR 16940
Subpart Q: Synthetic Organic Chemical and Polymer Manufacturing Plant
219.421General Requirements9/27/19939/9/1994, 59 FR 46562
219.422Inspection Program Plan for Leaks9/27/19939/9/1994, 59 FR 46562
219.423Inspection Program for Leaks9/27/19939/9/1994, 59 FR 46562
219.424Repairing Leaks9/27/19939/9/1994, 59 FR 46562
219.425Recordkeeping for Leaks9/27/19939/9/1994, 59 FR 46562
219.426Report for Leaks9/27/19939/9/1994, 59 FR 46562
219.427Alternative Program for Leaks9/27/19939/9/1994, 59 FR 46562
219.428Open-Ended Valves9/27/19939/9/1994, 59 FR 46562
219.429Standards for Control Devices9/27/19939/9/1994, 59 FR 46562
219.431Applicability5/9/19953/23/1998, 63 FR 13784
219.432Control Requirements5/9/19953/23/1998, 63 FR 13784
219.433Performance and Testing Requirements5/9/19953/23/1998, 63 FR 13784
219.434Monitoring Requirements5/9/19953/23/1998, 63 FR 13784
219.435Recordkeeping and Reporting Requirements5/9/19953/23/1998, 63 FR 13784
219.436Compliance Date5/9/19953/23/1998, 63 FR 13784
Subpart R: Petroleum Refining and Related Industries; Asphalt Materials
219.441Petroleum Refinery Waste Gas Disposal9/27/19939/9/1994, 59 FR 46562
219.442Vacuum Producing Systems8/16/19919/9/1994, 59 FR 46562
219.443Wastewater (Oil/Water) Separator9/27/19939/9/1994, 59 FR 46562
219.444Process Unit Turnarounds8/16/19919/9/1994, 59 FR 46562
219.445Leaks: General Requirements9/27/19939/9/1994, 59 FR 46562
219.446Monitoring Program Plan for Leaks9/27/19939/9/1994, 59 FR 46562
219.447Monitoring Program for Leaks9/27/19939/9/1994, 59 FR 46562
219.448Recordkeeping for Leaks8/16/19919/9/1994, 59 FR 46562
219.449Reporting for Leaks9/27/19939/9/1994, 59 FR 46562
219.450Alternative Program for Leaks9/27/19939/9/1994, 59 FR 46562
219.451Sealing Device Requirements8/16/19919/9/1994, 59 FR 46562
219.452Compliance Schedule for Leaks9/27/19939/9/1994, 59 FR 46562
Subpart S: Rubber and Miscellaneous Plastic Products
219.461Manufacture of Pneumatic Rubber Tires9/27/19939/9/1994, 59 FR 46562
219.462Green Tire Spraying Operations9/27/19939/9/1994, 59 FR 46562
219.463Alternative Emission Reduction Systems9/27/19939/9/1994, 59 FR 46562
219.464Emission Testing9/27/19939/9/1994, 59 FR 46562
Subpart T: Pharmaceutical Manufacturing
219.480Applicability5/9/19953/12/1997, 62 FR 11327
219.481Control of Reactors, Distillation Units, Crystallizers, Centrifuges and Vacuum Dryers9/27/19939/9/1994, 59 FR 46562
219.482Control of Air Dryers, Production Equipment Exhaust Systems and Filters9/27/19939/9/1994, 59 FR 46562
219.483Material Storage and Transfer9/27/19939/9/1994, 59 FR 46562
219.484In-Process Tanks8/16/19919/9/1994, 59 FR 46562
219.485Leaks9/27/19939/9/1994, 59 FR 46562
219.486Other Emission Units9/27/19939/9/1994, 59 FR 46562
219.487Testing9/27/19939/9/1994, 59 FR 46562
219.488Monitoring for Air Pollution Control Equipment8/16/19919/9/1994, 59 FR 46562
219.489Recordkeeping for Air Pollution Control Equipment9/27/19939/9/1994, 59 FR 46562
Subpart V: Batch Operations and Air Oxidation Processes
219.500Applicability for Batch Operations5/22/19954/2/1996, 61 FR 14484
219.501Control Requirements for Batch Operations5/22/19954/2/1996, 61 FR 14484
219.502Determination of Uncontrolled Total Annual Mass Emissions and Actual Weighted Average Flow Rate Values for Batch Operations5/22/19954/2/1996, 61 FR 14484
219.503Performance and Testing Requirements for Batch Operations5/22/19954/2/1996, 61 FR 14484
219.504Monitoring Requirements for Batch Operations5/22/19954/2/1996, 61 FR 14484
219.505Reporting and Recordkeeping for Batch Operations5/22/19954/2/1996, 61 FR 14484
219.506Compliance Date5/22/19954/2/1996, 61 FR 14484
219.520Emission Limitations for Air Oxidation Processes11/15/19949/27/1995, 60 FR 49770
219.522Savings Clause11/15/19949/27/1995, 60 FR 49770
219.523Compliance11/15/19949/27/1995, 60 FR 49770
219.524Determination of Applicability11/15/19949/27/1995, 60 FR 49770
219.526Testing and Monitoring8/16/19919/9/1994, 59 FR 46562
Subpart W: Agriculture
219.541Pesticide Exception9/27/19939/9/1994, 59 FR 46562
Subpart X: Construction
219.561Architectural Coatings8/16/19919/9/1994, 59 FR 46562
219.562Paving Operations9/27/19939/9/1994, 59 FR 46562
219.563Cutback Asphalt8/16/19919/9/1994, 59 FR 46562
Subpart Y: Gasoline Distribution
219.581Bulk Gasoline Plants9/27/19939/9/1994, 59 FR 46562
219.582Bulk Gasoline Terminals9/27/19939/9/1994, 59 FR 46562
219.583Gasoline Dispensing Operations—Storage Tank Filling Operations12/23/20133/13/2015, 80 FR 13248
219.584Gasoline Delivery Vessels9/27/19939/9/1994, 59 FR 46562
Subpart Z: Dry Cleaners
219.607Standards for Petroleum Solvent Dry Cleaners8/16/19919/9/1994, 59 FR 46562
219.608Operating Practices for Petroleum Solvent Dry Cleaners9/27/19939/9/1994, 59 FR 46562
219.609Program for Inspection and Repair of Leaks9/27/19939/9/1994, 59 FR 46562
219.610Testing and Monitoring9/27/19939/9/1994, 59 FR 46562
219.611Exemption for Petroleum Solvent Dry Cleaners9/27/19939/9/1994, 59 FR 46562
Subpart AA: Paint and Ink Manufacturing
219.620Applicability9/27/19939/9/1994, 59 FR 46562
219.621Exemption for Waterbase Material and Heatset-Offset Ink9/27/19939/9/1994, 59 FR 46562
219.623Permit Conditions9/27/19939/9/1994, 59 FR 46562
219.624Open-Top Mills, Tanks, Vats or Vessels9/27/19939/9/1994, 59 FR 46562
219.625Grinding Mills8/16/19919/9/1994, 59 FR 46562
219.626Storage Tanks8/16/19919/9/1994, 59 FR 46562
219.628Leaks9/27/19939/9/1994, 59 FR 46562
219.630Clean Up8/16/19919/9/1994, 59 FR 46562
219.636Compliance Schedule9/27/19939/9/1994, 59 FR 46562
219.637Recordkeeping and Reporting9/27/19939/9/1994, 59 FR 46562
Subpart BB: Polystyrene Plants
219.640Applicability9/27/19939/9/1994, 59 FR 46562
219.642Emissions Limitation at Polystyrene Plants9/27/19939/9/1994, 59 FR 46562
219.644Emissions Testing9/27/19939/9/1994, 59 FR 46562
Subpart GG: Marine Terminals
219.760Applicability10/25/19944/3/1995, 60 FR 16801
219.762Control Requirements10/25/19944/3/1995, 60 FR 16801
219.764Compliance Certification10/25/19944/3/1995, 60 FR 16801
219.766Leaks10/25/19944/3/1995, 60 FR 16801
219.768Testing and Monitoring10/25/19944/3/1995, 60 FR 16801
219.770Recordkeeping and Reporting10/25/19944/3/1995, 60 FR 16801
Subpart HH: Motor Vehicle Refinishing
219.780Emission Limitations5/9/19957/25/1996, 61 FR 38577
219.782Alternative Control Requirements5/9/19957/25/1996, 61 FR 38577
219.784Equipment Specifications1/28/201310/6/2014, 79 FR 60070
219.786Surface Preparation Materials5/9/19957/25/1996, 61 FR 38577
219.787Work Practices5/9/19957/25/1996, 61 FR 38577
219.788Testing5/9/19957/25/1996, 61 FR 38577
219.789Monitoring and Recordkeeping for Control Devices5/9/19957/25/1996, 61 FR 38577
219.791Compliance Date5/9/19957/25/1996, 61 FR 38577
Subpart II: Fiberglass Boat Manufacturing Materials
219.890Applicability9/14/20103/23/2012, 77 FR 16940
219.891Emission Limitations and Control Requirements7/27/20113/23/2012, 77 FR 16940
219.892Testing and Monitoring Requirements7/27/20113/23/2012, 77 FR 16940
219.894Recordkeeping and Reporting Requirements7/27/20113/23/2012, 77 FR 16940
Subpart JJ: Miscellaneous Industrial Adhesives
219.900Applicability9/14/20103/23/2012, 77 FR 16940
219.901Emission Limitations and Control Requirements7/27/20113/23/2012, 77 FR 16940
219.902Testing Requirements7/27/20113/23/2012, 77 FR 16940
219.903Monitoring Requirements7/27/20113/23/2012, 77 FR 16940
219.904Recordkeeping and Reporting Requirements7/27/20113/23/2012, 77 FR 16940
Subpart PP: Miscellaneous Fabricated Product Manufacturing Processes
219.920Applicability9/27/19935/7/1996, 61 FR 20455
219.923Permit Conditions9/27/19935/7/1996, 61 FR 20455
219.926Control Requirements5/9/19955/7/1996, 61 FR 20455
219.927Compliance Schedule9/27/19935/7/1996, 61 FR 20455
219.928Testing9/27/19935/7/1996, 61 FR 20455
Subpart QQ: Miscellaneous Formulation Manufacturing Processes
219.940Applicability9/27/19935/7/1996, 61 FR 20455
219.943Permit Conditions9/27/19935/7/1996, 61 FR 20455
219.946Control Requirements5/9/19955/7/1996, 61 FR 20455
219.947Compliance Schedule9/27/19935/7/1996, 61 FR 20455
219.948Testing9/27/19935/7/1996, 61 FR 20455
Subpart RR: Miscellaneous Organic Chemical Manufacturing Processes
219.960Applicability9/27/19935/7/1996, 61 FR 20455
219.963Permit Conditions9/27/19935/7/1996, 61 FR 20455
219.966Control Requirements5/9/19955/7/1996, 61 FR 20455
219.967Compliance Schedule9/27/19935/7/1996, 61 FR 20455
219.968Testing9/27/19935/7/1996, 61 FR 20455
Subpart TT: Other Emission Units
219.980Applicability5/9/19953/12/1997, 62 FR 11327
219.983Permit Conditions9/27/19935/7/1996, 61 FR 20455
219.986Control Requirements5/9/19955/7/1996, 61 FR 20455
219.987Compliance Schedule9/27/19935/7/1996, 61 FR 20455
219.988Testing9/27/19935/7/1996, 61 FR 20455
Subpart UU: Recordkeeping and Reporting
219.990Exempt Emission Units9/27/19935/7/1996, 61 FR 20455
219.991Subject Emission Units9/27/19935/7/1996, 61 FR 20455
219.Appendix A:List of Chemicals Defining Synthetic Organic Chemical and Polymer Manufacturing9/27/19939/9/1994, 59 FR 46562
219.Appendix B:VOM Measurement Techniques for Capture Efficiency (Repealed)9/27/19939/9/1994, 59 FR 46562
219.Appendix C:Reference Methods and Procedures9/27/19939/9/1994, 59 FR 46562
219.Appendix D:Coefficients for the Total Resource Effectiveness Index (TRE) Equation9/27/19939/9/1994, 59 FR 46562
219.Appendix E:List of Affected Marine Terminals2/15/19964/3/1995, 60 FR 16801
219.Appendix G:TRE Index Measurements for SOCMI Reactors and Distillation Units5/9/19953/23/1998, 63 FR 13784
219.Appendix H:Baseline VOM Content Limitations for Subpart F, Section 219.212 Cross-Line Averaging5/9/19952/13/1996, 61 FR 5511
Part 223: Standards and Limitations for Organic Material Emissions for Area Sources
Subpart A: General Provisions
223.100Severability6/8/20095/6/2013, 78 FR 26258
223.105Abbreviations and Acronyms6/8/20095/6/2013, 78 FR 26258
223.120Incorporations by Reference6/8/20095/6/2013, 78 FR 26258
Subpart B: Consumer and Commercial Products
223.200Purpose6/8/20095/6/2013, 78 FR 26258
223.201Applicability5/4/20125/6/2013, 78 FR 26258
223.203Definitions for Subpart B5/4/20125/6/2013, 78 FR 26258
223.205Standards5/4/20125/6/2013, 78 FR 26258
223.206Diluted Products6/8/20095/6/2013, 78 FR 26258
223.207Products Registered Under FIFRA5/4/20125/6/2013, 78 FR 26258
223.208Requirements for Aerosol Adhesives5/4/20125/6/2013, 78 FR 26258
223.209Requirements for Floor Wax Strippers6/8/20095/6/2013, 78 FR 26258
223.210Products Containing Ozone-Depleting Compounds6/8/20095/6/2013, 78 FR 26258
223.211Requirements for Adhesive Removers, Aerosol Adhesives, Contact Adhesives, Electrical Cleaners, Electronic Cleaners, Footwear or Leather Care Products, General Purpose Degreasers, and Graffiti Removers5/4/20125/6/2013, 78 FR 26258
223.220Requirements for Charcoal Lighter Material6/8/20095/6/2013, 78 FR 26258
223.230Exemptions6/8/20095/6/2013, 78 FR 26258
223.240Innovative Product Exemption6/8/20095/6/2013, 78 FR 26258
223.245Alternative Compliance Plans6/8/20095/6/2013, 78 FR 26258
223.250Product Dating6/8/20095/6/2013, 78 FR 26258
223.255Additional Product Dating Requirements6/8/20095/6/2013, 78 FR 26258
223.260Most Restrictive Limit6/8/20095/6/2013, 78 FR 26258
223.265Additional Labeling Requirements for Aerosol Adhesives, Adhesive Removers, Electronic Cleaners, Electrical Cleaners, Energized Electrical Cleaners, and Contact Adhesives6/8/20095/6/2013, 78 FR 26258
223.270Reporting Requirements6/8/20095/6/2013, 78 FR 26258
223.275Special Recordkeeping Requirements for Consumer Products That Contain Perchloroethylene or Methylene Chloride6/8/20095/6/2013, 78 FR 26258
223.280Calculating Illinois Sales6/8/20095/6/13, 78 FR 26258
223.285Test Methods6/8/20095/6/2013, 78 FR 26258
Subpart C: Architectural and Industrial Maintenance Coatings
223.300Purpose6/8/20095/6/2013, 78 FR 26258
223.305Applicability5/4/20125/6/2013, 78 FR 26258
223.307Definitions for Subpart C6/8/20095/6/2013, 78 FR 26258
223.310Standards6/8/20095/6/2013, 78 FR 26258
223.320Container Labeling Requirements6/8/20095/6/2013, 78 FR 26258
223.330Reporting Requirements6/8/20095/6/2013, 78 FR 26258
223.340Compliance Provisions and Test Methods6/8/20095/6/2013, 78 FR 26258
223.350Alternative Test Methods6/8/20095/6/2013, 78 FR 26258
223.360Methacrylate Traffic Coating Markings6/8/20095/6/2013, 78 FR 26258
223.370Test Methods6/8/20095/6/2013, 78 FR 26258
Part 225: Control of Emissions From Large Combustion Sources
Subpart A: General Provisions
225.120Abbreviations and Acronyms8/31/200710/16/2007, 72 FR 58528
225.130Definitions8/31/200710/16/2007, 72 FR 58528
225.140Incorporations by Reference8/31/200710/16/2007, 72 FR 58528
225.150Commence Commercial Operation8/31/200710/16/2007, 72 FR 58528
Subpart B: Control of Mercury Emissions From Coal-Fired Electric Generating Units
225.233Multi-Pollutant Standard (MPS)6/26/20097/6/2012, 77 FR 39943Only (a), (b), (e), and (g).
225.291Combined Pollutant Standard: Purpose12/7/20152/28/2018, 83 FR 8612
225.292Applicability of the Combined Pollutant Standard12/7/20152/28/2018, 83 FR 8612
225.293Combined Pollutant Standard: Notice of Intent12/7/20152/28/2018, 83 FR 8612
225.295Combined Pollutant Standard: Emission Standards for NOX and SO212/7/20152/28/2018, 83 FR 8612 Except (a)(4).
225.296Combined Pollutant Standard: Control Technology Requirements for NOX, SO2, and PM Emissions12/7/20152/28/2018, 83 FR 8612 Except (d).
Subpart C: Clean Air Act Interstate Rule (CAIR) SO2 Trading Program
225.300Purpose8/31/200710/16/2007, 72 FR 58528
225.305Applicability8/31/200710/16/2007, 72 FR 58528
225.310Compliance Requirements8/31/200710/16/2007, 72 FR 58528
225.315Appeal Procedures8/31/200710/16/2007, 72 FR 58528
225.320Permit Requirements8/31/200710/16/2007, 72 FR 58528
225.325Trading Program8/31/200710/16/2007, 72 FR 58528
Subpart D: CAIR NOX Annual Trading Program
225.400Purpose8/31/200710/16/2007, 72 FR 58528
225.405Applicability8/31/200710/16/2007, 72 FR 58528
225.410Compliance Requirements8/31/200710/16/2007, 72 FR 58528
225.415Appeal Procedures8/31/200710/16/2007, 72 FR 58528
225.420Permit Requirements8/31/200710/16/2007, 72 FR 58528
225.425Annual Trading Budget8/31/200710/16/2007, 72 FR 58528
225.430Timing for Annual Allocations8/31/200710/16/2007, 72 FR 58528
225.435Methodology for Calculating Annual Allocations8/31/200710/16/2007, 72 FR 58528
225.440Annual Allocations8/31/200710/16/2007, 72 FR 58528
225.445New Unit Set-Aside (NUSA)8/31/200710/16/2007, 72 FR 58528
225.450Monitoring, Recordkeeping and Reporting Requirements for Gross Electrical Output and Useful Thermal Energy8/31/200710/16/2007, 72 FR 58528
225.455Clean Air Set-Aside (CASA)8/31/200710/16/2007, 72 FR 58528
225.460Energy Efficiency and Conservation, Renewable Energy, and Clean Technology Projects8/31/200710/16/2007, 72 FR 58528
225.465Clean Air Set-Aside (CASA) Allowances8/31/200710/16/2007, 72 FR 58528
225.470Clean Air Set-Aside (CASA) Applications8/31/200710/16/2007, 72 FR 58528
225.475Agency Action on Clean Air Set-Aside (CASA) Applications8/31/200710/16/2007, 72 FR 58528
225.480Compliance Supplement Pool8/31/200710/16/2007, 72 FR 58528
Subpart E: CAIR NOX Ozone Season Trading Program
225.500Purpose8/31/200710/16/2007, 72 FR 58528
225.505Applicability8/31/200710/16/2007, 72 FR 58528
225.510Compliance Requirements8/31/200710/16/2007, 72 FR 58528
225.515Appeal Procedures8/31/200710/16/2007, 72 FR 58528
225.520Permit Requirements8/31/200710/16/2007, 72 FR 58528
225.525Ozone Season Trading Budget8/31/200710/16/2007, 72 FR 58528
225.530Timing for Ozone Season Allocations8/31/200710/16/2007, 72 FR 58528
225.535Methodology for Calculating Ozone Season Allocations8/31/200710/16/2007, 72 FR 58528
225.540Ozone Season Allocations8/31/200710/16/2007, 72 FR 58528
225.545New Unit Set-Aside (NUSA)8/31/200710/16/2007, 72 FR 58528
225.550Monitoring, Recordkeeping and Reporting Requirements for Gross Electrical Output and Useful Thermal Energy8/31/200710/16/2007, 72 FR 58528
225.555Clean Air Set-Aside (CASA)8/31/200710/16/2007, 72 FR 58528
225.560Energy Efficiency and Conservation, Renewable Energy, and Clean Technology Projects8/31/200710/16/2007, 72 FR 58528
225.565Clean Air Set-Aside (CASA) Allowances8/31/200710/16/2007, 72 FR 58528
225.570Clean Air Set-Aside (CASA) Applications8/31/200710/16/2007, 72 FR 58528
225.575Agency Action on Clean Air Set-Aside (CASA) Applications8/31/200710/16/2007, 72 FR 58528
225.Appendix ASpecified EGUs for Purposes of the CPS Coal-Fired Boilers as of July 1, 201612/7/20152/28/2018, 83 FR 8612
Part 226: Standards and Limitations for Certain Sources of Lead
226.100Severability4/21/20143/28/2018, 83 FR 13198
226.105Scope and Organization4/21/20143/28/2018, 83 FR 13198
226.110Abbreviations and Acronyms4/21/20143/28/2018, 83 FR 13198
226.115Definitions4/21/20143/28/2018, 83 FR 13198
226.120Incorporations by Reference4/21/20143/28/2018, 83 FR 13198
226.125Applicability4/21/20143/28/2018, 83 FR 13198
226.130Compliance Date4/21/20143/28/2018, 83 FR 13198
226.140Lead Emission Standards4/21/20143/28/2018, 83 FR 13198
226.150Operational Monitoring for Control Device4/21/20143/28/2018, 83 FR 13198
226.155Total Enclosure4/21/20143/28/2018, 83 FR 13198
226.160Operational Measurement for Total Enclosure4/21/20143/28/2018, 83 FR 13198
226.165Inspection4/21/20143/28/2018, 83 FR 13198
226.170Lead Fugitive Dust Operating Program4/21/20143/28/2018, 83 FR 13198
226.175Emissions Testing4/21/20143/28/2018, 83 FR 13198
226.185Recordkeeping and Reporting4/21/20143/28/2018, 83 FR 13198
Subchapter i: Open Burning
Part 237: Open Burning
Subpart A: General Provisions
237.101Definitions9/7/19715/31/1972, 37 FR 10862Approved as Rule 401.
237.102Prohibitions9/7/19715/31/1972, 37 FR 10862Approved as Rule 402.
237.103Explosive Wastes9/7/19715/31/1972, 37 FR 10862Approved as Rule 405.
237.110Local Enforcement9/7/19715/31/1972, 37 FR 10862Approved as Rule 406.
237.120Exemptions9/7/19715/31/1972, 37 FR 10862Approved as Rule 403.
Subpart B: Permits
237.201Permits9/7/19715/31/1972, 37 FR 10862Approved as Rule 404.
Subchapter k: Emission Standards and Limitations for Mobile Sources
Part 240: Mobile Sources
Subpart A: Definitions and General Provisions
240.101Preamble12/20/19948/13/2014, 79 FR 47377
240.102Definitions2/1/20128/13/2014, 79 FR 47377
240.103Prohibitions4/14/19728/13/2014, 79 FR 47377
240.104Inspection2/1/20128/13/2014, 79 FR 47377
240.105Penalties2/1/20128/13/2014, 79 FR 47377
240.106Determination of Violation2/1/20128/13/2014, 79 FR 47377
240.107Incorporations by Reference3/18/20118/13/2014, 79 FR 47377
Subpart B: Emissions
240.121Smoke Emissions2/1/20128/13/2014, 79 FR 47377
240.122Diesel Engine Emissions Standards for Locomotives4/7/19928/13/2014, 79 FR 47377
240.123Liquid Petroleum Gas Fuel Systems2/1/20128/13/2014, 79 FR 47377
Subpart C: Smoke Opacity Standards and Test Procedures for Diesel-Powered Heavy Duty Vehicles
240.140Applicability2/26/20018/13/2014, 79 FR 47377
240.141Smoke Opacity Standards and Test Procedures for Diesel-Powered Heavy Duty Vehicles2/26/20018/13/2014, 79 FR 47377
Subpart D: Steady-State Idle Mode Test Emission Standards
240.151Applicability2/1/20128/13/2014, 79 FR 47377
240.152Steady-State Idle Mode Vehicle Exhaust Emission Standards3/18/20118/13/2014, 79 FR 47377
240.153Compliance Determination3/18/20118/13/2014, 79 FR 47377
Subpart F: Evaporative Test Standards
240.171Applicability2/1/20128/13/2014, 79 FR 47377
240.172Evaporative System Integrity Test Standards7/13/19988/13/2014, 79 FR 47377
Subpart G: On-Road Remote Sensing Test Emission Standards
240.181Applicability3/18/20118/13/2014, 79 FR 47377
240.182On-Road Remote Sensing Emission Standards3/18/20118/13/2014, 79 FR 47377
240.183Compliance Determination7/13/19988/13/2014, 79 FR 47377
Subpart H: On-Board Diagnostic Test Standards
240.191Applicability3/18/20118/13/2014, 79 FR 47377
240.192On-Board Diagnostic Test Standards12/18/20018/13/2014, 79 FR 47377
240.193Compliance Determination12/18/20018/13/2014, 79 FR 47377
Subpart I: Visual Inspection Test Standards
240.201Applicability2/1/20128/13/2014, 79 FR 47377
240.202Visual Inspection Test Standards2/1/20128/13/2014, 79 FR 47377
240.203Compliance Determination2/1/20128/13/2014, 79 FR 47377
240.Appendix A:Rule Into Section Table2/1/20128/13/2014, 79 FR 47377
240.Appendix B:Section Into Rule Table2/1/20128/13/2014, 79 FR 47377
Part 241: Clean Fuel Fleet Program
Subpart A: General Provisions
241.101Other Definitions9/11/19953/19/1996, 61 FR 11139
241.102Definitions9/11/19953/19/1996, 61 FR 11139
241.103Abbreviations9/11/19953/19/1996, 61 FR 11139
241.104Incorporations by Reference9/11/19953/19/1996, 61 FR 11139
Subpart B: General Requirements
241.110Applicability9/11/19953/19/1996, 61 FR 11139
241.111Exemptions9/11/19953/19/1996, 61 FR 11139
241.112Registration of Fleet Owners or Operators9/11/19953/19/1996, 61 FR 11139
241.113Control Requirements11/25/19972/17/1999, 64 FR 7788
241.114Conversions9/11/19953/19/1996, 61 FR 11139
241.115Operating Requirements9/11/19953/19/1996, 61 FR 11139
Subpart C: Credits
241.130Clean Fuel Fleet Credit Program11/25/19972/17/1999, 64 FR 7788
241.131Credit Provisions9/11/19953/19/1996, 61 FR 11139
Subpart D: Recordkeeping and Reporting
241.140Reporting Requirements11/25/19972/17/1999, 64 FR 7788
241.141Recordkeeping Requirements9/11/19953/19/1996, 61 FR 11139
241.142Report of Credit Activities9/11/19953/19/1996, 61 FR 11139
241.Appendix A:Emission Standards for Clean Fuel Vehicles9/11/19953/19/1996, 61 FR 11139
241.Appendix B:Credit Values11/25/19972/17/1999, 64 FR 7788
Subchapter l: Air Quality Standards and Episodes
Part 243: Air Quality Standards
Subpart A: General Provisions
243.101Definitions10/23/201712/21/2018, 83 FR 65537
243.103Applicability7/29/20135/20/2015, 80 FR 28835
243.104Nondegradation10/25/20115/23/2013, 78 FR 30770
243.105Air Quality Monitoring Data Influenced by Exceptional Events10/23/201712/21/2018, 83 FR 65537
243.106Monitoring4/14/19722/21/1980, 45 FR 11472
243.107Reference Conditions11/27/20136/10/2016, 81 FR 37517
243.108Incorporation by Reference5/29/201812/21/2018, 83 FR 65537
Subpart B: Standards and Measurement Methods
243.120PM10 and PM2.510/23/201712/21/2018, 83 FR 65537
243.122Sulfur Oxides (Sulfur Dioxide), and11/27/20136/10/2016, 81 FR 37517
243.123Carbon Monoxide7/29/20135/20/2015, 80 FR 28835
243.124Nitrogen Oxides (Nitrogen Dioxide as Indicator)1/23/20177/18/2017, 82 FR 32771
243.125Ozone1/23/20177/18/2017, 82 FR 32771
243.126Lead, and7/29/20135/20/2015, 80 FR 28835
Part 244: Episodes
Subpart A: Definitions and General Provisions
244.101Definitions5/15/19921/12/1993, 58 FR 3844
244.102Responsibility of the Agency8/18/19722/21/1980, 45 FR 11472Approved as Rule 402.
244.103Determination of Required Actions8/18/19722/21/1980, 45 FR 11472Approved as Rule 402.
244.104Determination of Atmospheric Conditions8/18/19722/21/1980, 45 FR 11472Approved as Rule 402.
244.105Determination of Expected Contaminant Emissions8/18/19722/21/1980, 45 FR 11472Approved as Rule 402.
244.106Monitoring5/15/19921/12/1993, 58 FR 3844
244.107Determination of Areas Affected5/15/19921/12/1993, 58 FR 3844
244.108Failure To Comply With Episode Requirements8/18/19722/21/1980, 45 FR 11472Approved as Rule 402.
244.109Sealing of Offenders8/18/19722/21/1980, 45 FR 11472Approved as Rule 402.
Subpart B: Local Agency Responsibilities
244.121Local Agency Responsibilities5/15/19921/12/1993, 58 FR 3844
Subpart C: Episode Action Plans
244.141Requirement for Plans8/18/19722/21/1980, 45 FR 11472Approved as Rule 404.
244.142Facilities for Which Action Plans Are Required8/18/19722/21/1980, 45 FR 11472Approved as Rule 404.
244.143Submission of Plans8/18/19722/21/1980, 45 FR 11472Approved as Rule 404.
244.144Contents of Plans8/18/19722/21/1980, 45 FR 11472Approved as Rule 404.
244.145Processing Procedures8/18/19722/21/1980, 45 FR 11472Approved as Rule 404.
Subpart D: Episode Stages
244.161Advisory, Alert and Emergency Levels5/15/19921/12/1993, 58 FR 3844
244.162Criteria for Declaring an Advisory5/15/19921/12/1993, 58 FR 3844
244.163Criteria for Declaring a Yellow Alert5/15/19921/12/1993, 58 FR 3844
244.164Criteria for Declaring a Red Alert8/18/19722/21/1980, 45 FR 11472Approved as Rule 405(e).
244.165Criteria for Declaring an Emergency8/18/19722/21/1980, 45 FR 11472Approved as Rule 405(e).
244.166Criteria for Terminating Advisory, Alert and Emergency5/15/19921/12/1993, 58 FR 3844
244.167Episode Stage Notification5/15/19921/12/1993, 58 FR 3844
244.168Contents of Episode Stage Notification5/15/19921/12/1993, 58 FR 3844
244.169Actions During Episode Stages5/15/19921/12/1993, 58 FR 3844
244.Appendix D:Required Emission Reduction Actions5/15/19921/12/1993, 58 FR 3844
Chapter II: Environmental Protection Agency
Part 252: Public Participation in the Air Pollution Permit Program for Major Sources in Nonattainment Areas
Subpart A: Introduction
252.101Purpose6/1/19849/25/1985, 50 FR 38803
252.102Applicability6/1/19849/25/1985, 50 FR 38803
252.103Definitions6/1/19849/25/1985, 50 FR 38803
Subpart B: Procedures for Public Review
252.201Notice and Opportunity To Comment6/1/19849/25/1985, 50 FR 38803
252.202Draft Permit and Denial Letter6/1/19849/25/1985, 50 FR 38803
252.203Availability of Documents6/1/19849/25/1985, 50 FR 38803
252.204Opportunity for Public Hearing6/1/19849/25/1985, 50 FR 38803
Part 254: Annual Emissions Report
Subpart A: General Provisions
254.101Purpose7/17/20015/15/2002, 67 FR 34614
254.102Applicability4/20/20127/3/2013, 67 FR 40013
254.103Definitions7/17/20015/15/2002, 67 FR 34614
254.120Applicable Pollutants for Annual Emissions Reporting7/17/20015/15/2002, 67 FR 34614
254.132Failure To File a Complete Report7/17/20015/15/2002, 67 FR 34614
254.133Voluntary Submittal of Data5/14/19935/15/2002, 67 FR 34614
254.134Retention of Records7/17/20015/15/2002, 67 FR 34614
254.135Reporting of Errors7/17/20015/15/2002, 67 FR 34614
254.136Confidentiality and Trade Secret Protection7/17/20015/15/2002, 67 FR 34614
254.137Reporting Schedule7/17/20015/15/2002, 67 FR 34614
254.138Issuance of Source Inventory Report7/17/20015/15/2002, 67 FR 34614
Subpart B: Reporting Requirements for Large Sources
254.203Contents of Subpart B Annual Emissions Report7/17/20015/15/2002, 67 FR 34614
254.204Complete Reports7/17/20015/15/2002, 67 FR 34614
Subpart C: Reporting Requirements for Other Sources
254.303Contents of Subpart C Annual Emissions Report7/17/20015/15/2002, 67 FR 34614
254.306Complete Reports7/17/20015/15/2002, 67 FR 34614
Subpart E: Seasonal Emissions Report Under ERMS
254.501Contents of a Seasonal Emissions Report7/17/20015/15/2002, 67 FR 34614
Part 255: General Conformity: Criteria and Procedures
255.100Purpose3/6/199712/23/1997, 62 FR 67000
255.110Federal Requirement3/6/199712/23/1997, 62 FR 67000
255.120Applicability3/6/199712/23/1997, 62 FR 67000
255.140Definitions3/6/199712/23/1997, 62 FR 67000
255.150Abbreviations3/6/199712/23/1997, 62 FR 67000
255.160Incorporations by Reference3/6/199712/23/1997, 62 FR 67000
255.170Activities Exempt From Conformity Analysis3/6/199712/23/1997, 62 FR 67000
255.180Conformity Analysis3/6/199712/23/1997, 62 FR 67000
255.190Reporting Requirements3/6/199712/23/1997, 62 FR 67000
255.200Public Participation3/6/199712/23/1997, 62 FR 67000
255.210Frequency of Conformity Determinations3/6/199712/23/1997, 62 FR 67000
255.220Criteria for Determining Conformity of General Federal Actions3/6/199712/23/1997, 62 FR 67000
255.230Procedures for Conformity Determinations of General Federal Actions3/6/199712/23/1997, 62 FR 67000
255.240Mitigation of Air Quality Impacts3/6/199712/23/1997, 62 FR 67000
Part 276: Procedures To Be Followed in the Performance of Inspections of Motor Vehicle Emissions
Subpart A: General Provisions
276.101Purpose and Applicability6/28/20118/13/2014, 79 FR 47377
276.102Definitions1/30/20128/13/2014, 79 FR 47377
276.103Abbreviations6/28/20118/13/2014, 79 FR 47377
276.104Incorporations by Reference1/30/20128/13/2014, 79 FR 47377
276.105Sunset Provisions1/30/20128/13/2014, 79 FR 47377
Subpart B: Vehicle Emissions Inspection Procedures
276.201General Description of Vehicle Emissions Inspection Procedures1/30/20128/13/2014, 79 FR 47377
276.202Pollutants To Be Tested—Exhaust Test9/28/19988/13/2014, 79 FR 47377
276.203Dilution—Steady-State Idle Exhaust Test and Transient Loaded Mode Exhaust Test6/28/20118/13/2014, 79 FR 47377
276.204Steady-State Idle Exhaust Emissions Test Procedures6/28/20118/13/2014, 79 FR 47377
276.205Evaporative System Integrity Test Procedures6/28/20118/13/2014, 79 FR 47377
276.206Engine and Fuel Type Modifications6/14/19968/13/2014, 79 FR 47377
276.208On-Road Remote Sensing Test Procedures9/28/19988/13/2014, 79 FR 47377
276.209On-Board Diagnostic Test Procedures6/28/20118/13/2014, 79 FR 47377
276.210Visual Inspection Test Procedures1/30/20128/13/2014, 79 FR 47377276.210
Subpart C: Sticker or Certificate Issuance, Display, and Possession
276.301General Requirements6/28/20118/13/2014, 79 FR 47377
276.302Determination of Affected Counties1/30/20128/13/2014, 79 FR 47377
276.303Emissions Inspection Sticker or Certificate Design and Content6/28/20118/13/2014, 79 FR 47377
Subpart D: Waiver and Economic Hardship Extension Requirements
276.401Waiver Requirements6/28/20118/13/2014, 79 FR 47377
276.403Denial or Issuance of Waiver1/30/20128/13/2014, 79 FR 47377
276.404Economic Hardship Extension Requirements1/30/20128/13/2014, 79 FR 47377
276.405Outside of Affected Counties Annual Exemption Requirements1/30/20128/13/2014, 79 FR 47377
Subpart E: Test Equipment Specifications
276.501General Requirements6/28/20118/13/2014, 79 FR 47377
276.502Steady-State Idle Exhaust Test Analysis Systems Functional Requirements6/28/20118/13/2014, 79 FR 47377
276.503Steady-State Idle Exhaust Test Analysis Systems Performance Criteria6/28/20118/13/2014, 79 FR 47377
276.504Evaporative System Integrity Test Functional Requirements and Performance Criteria6/28/20118/13/2014, 79 FR 47377
276.507On-Road Remote Sensing Test Systems Functional Requirements and Performance Criteria6/28/20118/13/2014, 79 FR 47377
276.508On-Board Diagnostic Test Systems Functional Requirements and Performance Criteria6/28/20118/13/2014, 79 FR 47377
Subpart F: Equipment Maintenance and Calibration
276.601Steady-State Idle Test Equipment Maintenance9/28/19988/13/2014, 79 FR 47377
276.602Steady-State Idle Test Equipment Calibration6/28/20118/13/2014, 79 FR 47377
276.603Evaporative System Integrity Test Maintenance and Calibration9/28/19988/13/2014, 79 FR 47377
276.604Record Keeping6/28/20118/13/2014, 79 FR 47377
276.606On-Road Remote Sensing Test Systems Maintenance and Calibration9/28/19988/13/2014, 79 FR 47377
276.607On-Board Diagnostic Test Systems Maintenance and Calibration9/28/19988/13/2014, 79 FR 47377
Subpart G: Fleet Self-Testing Requirements
276.701General Requirements6/28/20118/13/2014, 79 FR 47377
276.702Fleet Inspection Permit6/28/20118/13/2014, 79 FR 47377
276.703Fleet Inspection Permittee Operating Requirements6/28/20118/13/2014, 79 FR 47377
276.704Private Official Inspection Station Auditing and Surveillance6/28/20118/13/2014, 79 FR 47377
276.705Fleet Vehicle Inspection Procedures (Renumbered)6/14/19968/13/2014, 79 FR 47377
Subpart H: Grievance Procedure
276.801General Requirements6/14/19968/13/2014, 79 FR 47377
276.802Procedure for Filing Grievance6/28/20118/13/2014, 79 FR 47377
276.803Agency Investigation6/28/20118/13/2014, 79 FR 47377
276.804Review of Agency's Determination6/14/19968/13/2014, 79 FR 47377
Subpart I: Notices
276.901General Requirements6/28/20118/13/2014, 79 FR 47377
276.902Vehicle Emissions Test Notice6/28/20118/13/2014, 79 FR 47377
Subpart J: Reciprocity With Other Jurisdictions
276.1001Requirements for Vehicles Registered in Affected Counties and Located in Other Jurisdictions Requiring Vehicle Emissions Inspection6/28/20118/13/2014, 79 FR 47377
276.1002Requirements for Vehicles Registered in Other Jurisdictions Requiring Vehicle Emissions Inspection and Located in an Affected County6/28/20118/13/2014, 79 FR 47377
Subpart K: Repair Facility Performance Reporting
276.1101Requirements for Collecting and Reporting Data Pertaining to the Repair of Vehicles That Failed or Were Rejected From an Emissions Inspection6/28/20118/13/2014, 79 FR 47377
Part 283: General Procedures for Emissions Tests Averaging
Subpart A: Introduction
283.110Purpose9/11/20005/9/2003, 68 FR 24885
283.120Applicability9/11/20005/9/2003, 68 FR 24885
283.130Definitions9/11/20005/9/2003, 68 FR 24885
Subpart B: Procedures for Averaging of Test Results
283.210Criteria for Averaging Tests9/11/20005/9/2003, 68 FR 24885
283.220Test Plan Requirements9/11/20005/9/2003, 68 FR 24885
283.230Changes to the Test Plan9/11/20005/9/2003, 68 FR 24885
283.240Averaging Procedure9/11/20005/9/2003, 68 FR 24885
283.250Compliance Determination9/11/20005/9/2003, 68 FR 24885
State Statutes
20 ILCS 605/46.13aCivil Administrative Code9/21/19928/30/1993, 58 FR 45448Subsection 46.13(a) [Approved Under Public Act 87-1177].
415 ILCS 5/9Illinois Environmental Protection Act6/21/19965/29/2002, 67 FR 37323Section 9(f) [Approved Under Public Act 89-491].
415 ILCS 5/9.1Illinois Environmental Protection Act9/17/199112/17/1992, 57 FR 59928(Ch. 111 1/2, par. 1009.1) par. 1009.1(a), (b), (c), (d) and (f). [Approved Under Public Act 87-555].
415 ILCS 5/9.9Illinois Environmental Protection Act7/1/200111/8/2001, 66 FR 56454Section 9.9(f) [Approved Under Public Act 92-0012].
415 ILCS 5/39.5Illinois Environmental Protection Act9/26/19928/30/1993, 58 FR 45448Subsection 20 [Approved Under Public Act 87-1213].
625 ILCS 5/13BIllinois Vehicle Code1/18/19947/25/1996, 61 FR 38582625 ILCS 5/13B [Approved Under Public Act 88-533].

(d) EPA approved state source-specific requirements.

EPA-Approved Illinois Source-Specific Requirements

Name of sourceOrder/permit No.State
effective
date
EPA
approval
date
Comments
Alumax Incorporated, Morris, ILPCB AS 92-139/1/19942/1/1996, 61 FR 3575
Argonne National LaboratoryPCB AS 03-412/18/20037/28/2004, 69 FR 44967
Bema Film Systems, Incorporated, DuPage CoPCB AS 00-111/18/200111/30/2001, 66 FR 59702
Central Can Company (CCC), Chicago, ILPCB AS 94-188/6/1998, eff. 7/1/19913/18/1999, 64 FR 13346
Chase Products Company, Broadview (Cook Co.)PCB AS 94-45/16/19966/9/1997, 62 FR 31341
City Water, Light & Power, City of Springfield90900466/23/20117/6/2012, 77 FR 39943Joint Construction and Operating Permit.
CP-D Acquisition Company, LLC. (formerly Cromwell-Phoenix, Inc)PCB AS 03-0511/20/200310/29/2008, 73 FR 64213
Ford Motor CompanyPCB, AS 02-0311/21/20023/22/2004, 69 FR 13239
Ford Motor Company Chicago Assembly PlantPCB, AS 05-59/1/20059/6/2006, 71 FR 52464
Greif Packaging, LLC, Naperville, DuPage CoPCB AS 2011-014/5/201210/22/2012, 77 FR 64422
IL Power Company's Baldwin Power StationPCB 79-79/8/19834/18/1990, 55 FR 14419Emission limits within Paragraph 1 of Final Order.
IPH/Ameren EnergyPCB 14-1011/21/201312/21/2015, 80 FR 79261Certificate of Acceptance, filed
with the Illinois Pollution Control Board Clerk's Office 12/20/13.
Kincaid Generation, LLC90500226/24/20117/6/2012, 77 FR 39943Joint Construction and Operating Permit.
Laclede Steel Sulfur dioxide plan9307003011/18/19934/20/1994, 59 FR 18752FESOP for boilers and reheat furnaces.
Leisure Properties LLC/D/B/A Crownline Boats, West Frankfort, IllinoisPCB AS 04-017/22/20044/20/2012, 77 FR 23622Effective date identified in error as 7/22/2002 in the document heading. Due to ownership change, the Board transferred the adjusted standard to Leisure Properties LLC D/B/A Crownline Boats by Board order AS04-l, effective 10/7/2010.
Louis Berkman Company, d/b/a/ the Swenson Spreader Company's Lindenwood, Ogle CoPCB, AS 97-55/7/19985/27/2004, 69 FR 30224
LTV Steel Company, Inc.981200915/14/19997/14/1999, 64 FR 37847Federally Enforceable State Operating Permit.
Midwest Generation, LLCPCB 12-1218/23/20127/20/2015, 80 FR 42726Certificate of Acceptance, dated 8/24/2012, filed with the Illinois Pollution Control Board Clerk's Office 8/27/2012.
Midwest Generation, LLCPCB 13-244/4/20137/20/2015, 80 FR 42726Certificate of Acceptance, dated 5/16/13, filed with the Illinois Pollution Control Board Clerk's Office 5/17/2013.
National Steel Corporation, Granite City Division9501000510/21/19973/11/1998, 63 FR 11842Joint Construction and Operating Permit.
Quantum Chemical Corporation, Morris, Aux Sable Township, Grundy CoPCB AS 92-1410/7/19934/3/1995, 60 FR 16803adjusted standard.
Reynolds Metals Company's McCook Sheet and Plate Plant in McCook, IL (in Cook Co.)PCB AS 91-89/21/19951/21/1997, 62 FR 2916
Royal Fiberglass Products, d/b/a Viking PoolsPCB AS 09-149/5/20137/14/2014, 79 FR 40673
Solar Corporation, Libertyville, ILPCB AS 94-27/20/19952/23/1998, 63 FR 8855
Sun Chemical Corporation, Northlake, ILPCB AS 99-45/20/19999/13/1999, 64 FR 49400
Vonco Products, Incorporated, Lake CoPCB AS 00-121/18/200111/30/2001, 66 FR 59704

(e) EPA approved nonregulatory and quasi-regulatory provisions.

EPA-Approved Illinois Nonregulatory and Quasi-Regulatory Provisions

Name of SIP provisionApplicable geographic or nonattainment areaState submittal dateEPA approval dateComments
Air quality surveillance networkState-wide12/20/19793/4/1981, 46 FR 15137
Coal banChicago Area10/22/19733/2/1976, 41 FR 8956
Compliance schedulesState-wide3/13/1973,
4/3/1973,
5/3/1973,
6/15/1973, and
8/7/1973
3/2/1976, 41 FR 8956
Ozone (8-hour, 2008) certification of emissions statement regulationsChicago and St. Louis areas5/9/20177/11/2017, 82 FR 31913Certification that Illinois' previously approved regulations at 35 IAC part 254 meet the emission statement requirements for the 2008 ozone NAAQS.
Ozone (8-hour, 2008) Nonattainment New Source Review RequirementsChicago area5/23/20182/6/2019, 84 FR 2063
Regional haze planStatewide6/24/20117/6/2012, 77 FR 39943
Regional Haze Progress ReportStatewide2/1/20174/12/2018, 83 FR 15744
Small business stationary source technical and environmental compliance assistance programState-wide11/12/19928/30/1993, 58 FR 45451
Total Suspended Particulate Control Strategy analysisState-wide10/1/19819/30/1982, 47 FR 43054
Transportation control planChicago Area4/17/19733/2/1976, 41 FR 8956
Transportation control planChicago Area4/30/19801/27/1981, 46 FR 8472
Transportation control planChicago Area8/20/1980 and 3/20/198111/16/1981, 46 FR 56196
Transportation control planPeoria Area10/15/198011/16/1981, 46 FR 56196
Transportation control planSt. Louis Area4/1/198111/16/1981, 46 FR 56196
Transportation control plansChicago and St. Louis areas12/3/198210/4/1990, 55 FR 40658
Attainment and Maintenance Plans
Carbon monoxide attainment demonstrationChicago Area5/4/198310/4/1990, 55 FR 40658
Lead (1978) attainment and maintenance planGranite City area9/30/19837/24/1984, 49 FR 29790
Lead (2008)—Clean Data DeterminationChicago AreaN/A8/25/2015, 80 FR 51131
Lead (2008) Redesignation and maintenance planChicago and Granite City areas9/22/20163/28/2018, 83 FR 13198
Ozone (1-hour) attainment demonstrationChicago area12/26/200011/13/2001, 66 FR 56904
Ozone (1-hour) attainment demonstrationSt. Louis area11/15/1999,
2/10/2000,
4/13/2001, and 4/30/2001
6/26/2001, 66 FR 33996EPA is disapproving the request for an exemption from the NOX NSR and certain NOX conformity requirements for Madison, Monroe, and St. Clair Counties.
Ozone (1-hour) attainment plan revisionChicago severe nonattainment area4/11/20039/15/2003, 68 FR 53887
Ozone (1-hour) redesignation and maintenance planJersey County11/12/19933/14/1995, 60 FR 13634
Ozone (1-hour) redesignation and maintenance planSt. Louis Area12/30/20025/12/2003, 68 FR 25542
Ozone (1-hour revoked) finding of attainmentChicago area1/30/200712/30/2008, 73 FR 79652
Ozone (8-hour, 1997) Determination of AttainmentChicago areaN/A7/8/2011, 76 FR 40262Correction to codification published on 3/12/2010 at 75 FR 12088.
Ozone (8-hour, 1997) Determination of AttainmentSt. Louis areaN/A6/9/2011, 76 FR 33647
Ozone (8-hour, 1997) maintenance plan revisionChicago area3/28/201410/6/2014, 79 FR 60073Revised VOC and NOX Motor Vehicle Emissions Budgets (MVEB) for the year 2025.
Ozone (8-hour, 1997) redesignation and maintenance planChicago area7/23/2009, and 9/16/20118/13/2012, 77 FR 48062
Ozone (8-hour, 1997) redesignation and maintenance planSt. Louis area5/26/2010, and 9/16/20116/12/2012, 77 FR 34819
Ozone (8-hour, 2008) Determination of AttainmentSt. Louis areaN/A6/27/2016, 81 FR 41444determination that the area attained by the 7/20/2016 attainment date.
Ozone (8-hour, 2008) redesignation and maintenance planSt. Louis area5/8/20173/1/2018, 83 FR 8756
PM10 maintenance planGranite City area3/19/1996, and 10/15/19963/11/1998, 47 FR 11842
PM10 maintenance planLake Calumet (Southeast Chicago), Cook County8/2/2005, as supplemented on 9/8/20059/22/2005, 70 FR 55545
PM10 maintenance planLaSalle County6/2/1995, and 1/9/19968/8/1996, 61 FR 41342
PM10 maintenance planLyons Township (McCook), Cook County8/2/20059/22/2005, 70 FR 55541
PM2.5 (1997)—Clean Data DeterminationSt. Louis areaN/A5/23/2011, 76 FR 29652
PM2.5 (1997)—Determination of AttainmentChicago areaN/A11/27/2009, 74 FR 62243
PM2.5 (1997)—Determination of AttainmentSt. Louis areaN/A6/27/2012, 77 FR 38184
PM2.5 (1997)—maintenance plan and motor vehicle emissions budgetsChicago area10/15/2010, supplemented on 9/16/2011, and 5/6/201310/2/2013, 78 FR 60704
PM2.5 (1997)—maintenance plan and motor vehicle emissions budgetsSt. Louis area12/6/20185/28/2019, 84 FR 24395
Sulfur dioxide (2010) nonattainment plansLemont and Pekin3/2/20162/1/2018, 83 FR 4591
Sulfur dioxide control strategyCincinnati, Pekin and Elm Grove Townships in Tazewell County and Logan and Limestone Townships in Peoria County3/24/1983 and 5/3/19838/8/1984, 49 FR 31685Correction to codification published on 2/9/1994 at 59 FR 5955.
Sulfur dioxide maintenance planPeoria and Hollis Townships in Peoria County and Groveland Township in Tazewell County11/10/199460 FR 17001, 4/4/1995
Emission Inventories
Emission inventory—1990 (1-hour ozone)Chicago and St. Louis areas11/12/19933/14/1995, 60 FR 13631
Emission inventories—2002 (NOX, primary PM2.5, SO2, ammonia, and VOC)Chicago area10/15/2010, supplemented on 5/6/201310/2/2013, 78 FR 60704
Emissions inventory—2002 (1997 8-hour ozone)St. Louis area5/26/2010, supplemented on 9/16/20116/12/2012, 77 FR 34819
Emissions inventory—2002 (1997 8-hour ozone)Chicago area6/21/2006, supplemented on 9/16/20118/13/2012, 77 FR 48062
Emissions inventories—2008 (NOX, primary PM2.5, SO2, ammonia, and VOC)St. Louis area12/6/20185/28/2019, 84 FR 24395
Emission inventory—2011 (2008 8-hour ozone)Chicago and St. Louis areas9/3/20143/7/2016, 81 FR 11671
Emission inventory—2012 (2008 Lead)Chicago and Granite City areas9/22/20163/28/2018, 83 FR 13198
Moderate Area & Above Ozone Requirements
15 percent rate-of-progress and 3 percent contingency plansChicago and St. Louis areas11/15/199312/18/1997, 62 FR 66279
Negative declaration—Natural gas/gasoline processing plantsState-wide11/14/198511/24/1986, 51 FR 42221
Negative declaration—Aerospace manufacturing and rework industryChicago and St. Louis areas10/11/19962/11/1997, 62 FR 6127
Negative declaration—Industrial cleaning solvents categorySt. Louis area10/2/19981/6/1999, 64 FR 756
Negative declaration—Industrial cleaning solvents categoryChicago area12/23/19992/7/2001, 66 FR 9206
Negative declaration—Industrial wastewater categoryChicago area12/23/19994/27/2001, 66 FR 21096
Negative declaration—Industrial wastewater categorySt. Louis area10/2/19981/6/1999, 64 FR 756
Negative declaration—Shipbuilding and ship repair industryChicago and St. Louis areas10/11/19962/11/1997, 62 FR 6126
NOX RACT waiver (1997 8-hour ozone)Chicago and St. Louis areas7/29/20102/22/2011, 76 FR 9655
NOX waiver—RACT, NSR, vehicle I/M, and general conformityChicago severe nonattainment area7/13/19941/26/1996, 61 FR 2428does not cover the exemption of NOX transportation conformity requirements.
NOX waiver—transportation conformity requirementsChicago severe nonattainment area6/20/19952/12/1996, 61 FR 5291
Photochemical assessment ambient monitoring system (PAMS)11/4/19932/25/1994, 59 FR 9091
Post-1996 Rate Of Progress PlanChicago area12/18/1997,
12/17/1999,
1/14/2000,
1/21/2000, and
2/17/2000
12/18/2000, 65 FR 78961Includes Contingency measure plan and Transportation Control Measures (TCMs).
Transportation control measures as part of the 15 percent rate-of-progress and 3 percent contingency plansSt. Louis area11/15/199312/18/1997, 62 FR 66279Work trip reductions; transit improvements; and traffic flow improvements.
Vehicle miles traveled (VMT) SIP and, transportation control measures (TCMs) as part of the 15 percent rate-of-progress planChicago area7/14/19949/21/1995, 60 FR 48896
Section 110(a)(2) Infrastructure Requirements
1997 8-hour Ozone NAAQS Infrastructure RequirementsStatewide12/12/20077/13/2011, 76 FR 41075CAA elements 110(a)(2)(A), (B), (C) with respect to enforcement, (D)(ii), (E) through (H), (J) except for prevention of significant deterioration (PSD), and (K) through (M) have been approved.
CAA elements 110(a)(2)(C) and (J) with respect to PSD have been disapproved.
1997 PM2.5 NAAQS Infrastructure RequirementsStatewide12/12/20077/13/2011, 76 FR 41075CAA elements 110(a)(2)(A), (B), (C) with respect to enforcement, (D)(ii), (E) through (H), (J) except for prevention of significant deterioration (PSD), and (K) through (M) have been approved.
CAA elements 110(a)(2)(C) and (J) with respect to PSD have been disapproved.
2006 24-hour PM2.5 NAAQS Infrastructure RequirementsStatewide8/9/2011, supplemented on 8/25/2011, and 6/27/20128/26/2015, 80 FR 51730CAA elements 110(a)(2)(A), (B), (C) with respect to enforcement, (D)(i)(II) with respect to visibility protection, (E)(i), (E)(iii), (F) through (H), (J) except for prevention of significant deterioration (PSD), and (K) through (M) have been approved.
CAA elements 110(a)(2)(E)(ii), (D)(ii) and the PSD portions of (C), (D)(i)(II), and (J) have been disapproved.
2008 Lead NAAQS Infrastructure RequirementsStatewide12/31/20127/16/2014, 79 FR 41439CAA elements 110(a)(2)(A), (B), (C) with respect to enforcement, (D)(i)(I), (D)(i)(II) with respect to visibility protection, (E)(i), (E)(iii), (F) through (H), (J) except for prevention of significant deterioration (PSD), and (K) through (M) have been approved.
CAA elements 110(a)(2)(D)(ii) and the PSD portions of (C), (D)(i)(II), and (J) have been disapproved.
2008 Ozone NAAQS Infrastructure RequirementsStatewide12/31/20128/26/2015, 80 FR 51730CAA elements 110(a)(2)(A), (B), (C) with respect to enforcement, (D)(i)(II) with respect to visibility protection, (E)(i), (E)(iii), (F) through (H), (J) except for prevention of significant deterioration (PSD), and (K) through (M) have been approved.
CAA elements 110(a)(2)(D)(ii), (E)(ii), and the PSD portions of (C), (D)(i)(II), and (J) have been disapproved.
2010 NO2 NAAQS Infrastructure RequirementsStatewide12/31/20125/22/2015, 80 FR 29535CAA elements 110(a)(2)(A), (B), (C) with respect to enforcement, (D)(i)(I), (D)(i)(II) with respect to visibility protection, (E)(i), (E)(iii), (F) through (H), (J) except for prevention of significant deterioration (PSD), and (K) through (M) have been approved.
CAA elements 110(a)(2)(D)(ii) and the PSD portions of (C), (D)(i)(II), and (J) have been disapproved.
2010 SO2 NAAQS Infrastructure RequirementsStatewide12/31/20125/22/2015, 80 FR 29535CAA elements 110(a)(2)(A), (B), (C) with respect to enforcement, (D)(i)(II) with respect to visibility protection, (E)(i), (E)(iii), (F) through (H), (J) except for prevention of significant deterioration (PSD), and (K) through (M) have been approved.
CAA elements 110(a)(2)(D)(ii) and the PSD portions of (C), (D)(i)(II), and (J) have been disapproved.
2012 PM2.5 NAAQS Infrastructure RequirementsStatewide9/29/20176/20/2019, 84 FR 28745Fully approving CAA transport requirements of (D)(i)(I).

[82 FR 30638, June 30, 2017, as amended at 82 FR 31915, July 11, 2017; 82 FR 32774, July 18, 2017; 83 FR 4593, Feb. 1, 2018; 83 FR 8615, Feb. 28, 2018; 83 FR 8757, Mar. 1, 2018; 83 FR 13201, Mar. 28, 2018; 83 FR 15746, Apr. 12, 2018; 83 FR 24407, May 29, 2018; 83 FR 24032, May 24, 2018; 83 FR 50855, Oct. 10, 2018; 83 FR 65540, Dec. 21, 2018; 84 FR 2067, Feb. 6, 2019; 84 FR 24397, May 28, 2019; 84 FR 28747, June 20, 2019]

Editorial Note: At 83 FR 50855, Oct. 10, 2018, §52.720(c) was amended in part by revising entries for 201.103, 201.104, and 211.4720; however, the revisions could not be completed because those entries did not exist.

return arrow Back to Top

§52.721   Classification of regions.

The Illinois plan was evaluated on the basis of the following classifications:

Air quality control regionPollutant
Particulate matterSulfur oxidesNitrogen dioxideCarbon monoxideOzone
Burlington-Keokuk InterstateIIIIIIIIIII
East Central Illinois IntrastateIIIIIIIIIIIIII
Metropolitan Chicago Interstate (Indiana-Illinois)IIIII
Metropolitan Dubuque InterstateIIIIIIIIIIIII
Metropolitan Quad Cities InterstateIIIIIIIIIIIII
Metropolitan St. Louis Interstate (Missouri-Illinois)IIIIIII
North Central Illinois IntrastateIIIAIIIIIIIII
Paducah (Kentucky)-Cairo (Illinois) InterstateIIIIIIIIIIII
Rockford (Illinois)-Janesville-Beloit (Wisconsin) InterstateIIIIIIIIIIIIII
Southeast Illinois IntrastateIIIIIIIIIIIIII
West Central Illinois IntrastateIIAIIIIIIIII

[37 FR 10862, May 31, 1972, as amended at 39 FR 16346, May 8, 1974; 45 FR 11493, Feb. 21, 1980]

return arrow Back to Top

§52.722   Approval status.

(a) With the exceptions set forth in this subpart, the Administrator approved Illinois' plan for the attainment and maintenance of the National Ambient Air Quality Standards under section 110 of the Clean Air Act. Furthermore, the Administrator finds the plan satisfies all requirements of part D, title I of the Clean Air Act as amended in 1977, except as noted below. In addition, continued satisfaction of the requirements of part D for the ozone portion of the SIP depends on the adoption and submittal of RACT requirements by July 1, 1980, for the sources covered by CTGs between January 1978 and January 1979 and adoption and submittal by each subsequent January of additional RACT requirements for sources covered by CTGs issued by the previous January.

(b) The Administrator finds that the transportation control plans for the East St. Louis and Chicago areas submitted on December 3, 1982, satisfy the related requirements of part D, title I of the Clean Air Act, as amended in 1977.

(c) The Administrator finds that the carbon monoxide control strategy submitted on May 4, 1983, satisfies all requirements of part D, title I of the Clean Air Act, as amended in 1977, except for section 172(b)(6).

[55 FR 40661, Oct. 4, 1990]

return arrow Back to Top

§52.723   [Reserved]

§52.724   Control strategy: Sulfur dioxide.

(a) Part D—Conditional Approval—The Illinois plan is approved provided that the following condition is satisfied:

(1) The plan includes a reanalysis of the Pekin, Illinois area, a submittal of the analysis results to USEPA, the proposal of any additional regulations to the Illinois Pollution Control Board necessary to insure attainment and maintenance of the sulfur dioxide standard, and the promulgation of any necessary regulations. The State must complete the reanalysis, submit the results to USEPA and submit any necessary, additional regulations to the Illinois Pollution Control Board by September 30, 1980. Any necessary regulation must be finally promulgated by the State and submitted to USEPA by September 30, 1981.

(2) Extension of Condition—USEPA approves the date of July 1, 1984 for submitting the draft sulfur dioxide rule revisions and supporting documentation as required in (a)(1) for Peoria, Hollis and Groveland Townships in Illinois. The State must complete final rule adoption as expeditiously as possible but no later than December 31, 1985.

(b) Part D—Disapproval—USEPA disapproves Rules 204(c)(1)(B), Rule 204(c)(1)(C), Rule 204(e)(1) and Rule 204(e)(2) for those sources for which these rules represent a relaxation of the federally enforceable State Implementation Plan. Rule 204(c)(1)(B), Rule 204(c)(1)(C), Rule 204(e)(1) and Rule 204(e)(2) are approved as not representing relaxations of the State Implementation Plan for the following sources:

Sources of 10 Million Btu per Hour or More Not Increasing Allowable Sulfur Dioxide Emissions as a Result of Record Rules 204(c) and 204(e) Because New Allowable Emissions Rate is Same as or Less Than Old Allowable Rate Pounds per Hour (Pounds per Million Btu)

CountyNameEmissions formerly allowable1Emissions now allowable without new permit application2
BooneChrysler1,760 (4.4)1,760 (4.4)
ChampaignChanute Air Base1,317 (3.0)1,317 (3.0)
CrawfordCIPS8,242 (5.1)8,242 (5.1)
DouglasUSI Chemicals8,022 (5.3)8,022 (5.3)
FultonFreeman Coal22.2 (1.2)22.2 (1.2)
La SalleDel Monte296 (3.9)296 (3.9)
MassacEEI Joppa36,865 (3.6)36,865 (3.6)
MontgomeryCIPS55,555 (5.8)55,555 (5.8)
Morgan......do24,000 (6.0)20,800 (5.2)
PutnamIllinois Power17,051 (5.8)17,051 (5.8)
Randolph......do381,339 (4.6)81,339 (4.6)
Rock IslandInternational Harvester1,643 (4.35)1,643 (4.35)
WilliamsonMarion Correctional396 (5.7)396 (5.7)

16.0 lbs/MMBTU of existing coal fired capacity or total 204(e)(2) emissions less actual oil fired and NSPS emissions, whichever is lower.

2Maximum allowable emissions for existing coal fired capacity according to revised rules 204(c) and 204(e) consolidated, usually equally equalling total emissions as given by 204(e)(2) less actual oil fired NSPS emissions. (In the one case wherein the new allowable limit is less than that given by 204(e)(2) the allowable emissions were determined by 204(e)(1) with which the source is required to comply.)

3Source is in compliance per 204(e)(3).

CIPS = Central Illinois Public Service.

EEI = Electric Energy Incorporated.

This disapproval does not in and of itself result in the growth restrictions of section 110(a)(2)(1).

(c) Disapproval—USEPA disapproves Rule 204(e)(4) as not being adequate to protect the NAAQS. This disapproval does not in and of itself result in the growth restrictions of section 110(a)(2)(I).

(d) Disapproval—USEPA disapproves Rule 204(f)(1)(D) as completely deregulating SO2 emissions from existing processes without providing an assessment of the ambient air quality impact or a showing that increasing the allowable emissions from these sources will not cause or contribute to violations of the NAAQS or PSD increments. This disapproval does not in and of itself result in the growth restrictions of section 110(a)(2)(I).

(e) Disapproval—USEPA disapproves Rule 204(h) for those sources for which USEPA has disapproved rules 204(c) and 204(e). This disapproval does not in and of itself result in the growth restrictions of section 110(a)(2)(I).

(f) Approval—USEPA approves rule 204(e)(3) for those sources able to show that the proposed emission rate will not cause or contribute to a violation of the NAAQS. The State must submit these emission limitations, along with the technical support to USEPA for approval.

(g) Part D—Approval—The State plan for Alton Township, Madison County, which consists of a federally Enforceable State Operating Permit controlling sulfur dioxide emissions from the boilers and reheat furnaces at Laclede Steel, which was submitted on November 18, 1993, is approved.

(h) Approval—On November 10, 1994, the Illinois Environmental Protection Agency submitted a sulfur dioxide redesignation request and maintenance plan for Peoria and Hollis Townships in Peoria County and Groveland Township in Tazewell County to redesignate the townships to attainment for sulfur dioxide. The redesignation request and maintenance plan meet the redesignation requirements in section 107(d)(3)(d) of the Clean Air Act (Act) as amended in 1990.

[45 FR 62806, 62809, Sept. 22, 1980, as amended at 50 FR 5250, Feb. 7, 1985; 59 FR 18753, Apr. 20, 1994; 60 FR 17001, Apr. 4, 1995]

return arrow Back to Top

§52.725   Control strategy: Particulates.

(a) [Reserved]

(b) Part D—Disapproval. (1) U.S. EPA disapproves the provisions of Rule 203(f) which allow the use of an equivalent method without review and approval of that method. Any source subject to Rule 203(f) which chooses to use an equivalent method must have that equivalent method submitted to U.S. EPA and approved as a SIP revision.

(2) U.S. EPA disapproves the following portions of Rule 203(d)(5) which regulate the control of particulate matter from specific sources within the iron and steel industry: Rule 205(d)(5)(B)(ii), Rule 205(d)(5)(B)(iii), Rule 205(d)(5)(D), and Rule 205(d)(5)(K).

(3) USEPA disapproves a proposed SIP revision submitted by the State on May 12, 1982, in the form of a May 18, 1981 Consent Decree (Civil Action 81-3009) to which USEPA, Illinois Environmental Protection Agency and National Steel Corporation are parties and a draft Alternative Control Strategy Permit. This submission was modified by the State, September 30, 1982, with the submission of a separate document embodying the elements of the Alternative Control Strategy. This separate document was intended to become an enforceable part of the SIP.

(c) Approval—On September 28, 1988, the State of Illinois submitted a committal SIP for particulate matter with an aerodynamic diameter equal to or less than 10 micrometers (PM10) for the Illinois Group II areas of concern in DuPage, Will, Rock Island, Macon, Randolph, and St. Clair Counties. The committal SIP contains all the requirements identified in the July 1, 1987, promulgation of the SIP requirements for PM10 at 52 FR 24681.

(d) Approval—On June 2, 1995, and January 9, 1996, the State of Illinois submitted a maintenance plan for the particulate matter nonattainment portion of LaSalle County, and requested that it be redesignated to attainment of the National Ambient Air Quality Standard for particulate matter. The redesignation request and maintenance plan satisfy all applicable requirements of the Clean Air Act.

(e) Approval—On March 19, 1996, and October 15, 1996, Illinois submitted requests to redesignate the Granite City Particulate Matter (PM) nonattainment area to attainment status for the PM National Ambient Air Quality Standards (NAAQS), as well as a maintenance plan for the Granite City area to ensure continued attainment of the NAAQS. The redesignation request and maintenance plan satisfy all applicable requirements of the Clean Air Act.

(f) On November 14, 1995, May 9, 1996, and June 14, 1996, the State of Illinois submitted State Implementation Plan (SIP) revision requests to meet commitments related to the conditional approval of Illinois' May 15, 1992, SIP submittal for the Lake Calumet (SE Chicago), McCook, and Granite City, Illinois, Particulate Matter (PM) nonattainment areas. The EPA is approving the SIP revision request as it applies to the McCook PM nonattainment area. For the McCook PM nonattainment area, all of the deficiencies of the May 15, 1992, submittal have been corrected.

(g) Approval—On May 5, 1992, November 14, 1995, May 9, 1996, June 14, 1996, February 3, 1997, October 16, 1997, October 21, 1997, February 1, 1999, and May 19, 1999, Illinois submitted SIP revision requests to meet the Part D particulate matter (PM) nonattainment plan requirements for the Lake Calumet, Granite City and McCook moderate PM nonattainment areas. The submittals include federally enforceable construction permit, application number 93040047, issued on January 11, 1999, to Acme Steel Company. The part D plans for these areas are approved.

(h) Approval—On August 2, 2005, the State of Illinois submitted a request to redesignate the Lyons Township (McCook), Cook County particulate matter nonattainment area to attainment of the NAAQS for particulate matter with an aerodynamic diameter less than or equal to a nominal 10 micrometers (PM-10). In its submittal, the State also requested that EPA approve the maintenance plan for the area into the Illinois PM SIP. The redesignation request and maintenance plan meet the redesignation requirements of the Clean Air Act.

(i) Approval—On August 2, 2005, and as supplemented on September 8, 2005, the State of Illinois submitted a request to redesignate the Lake Calumet (Southeast Chicago), Cook County particulate matter nonattainment area to attainment of the NAAQS for particulate matter with an aerodynamic diameter less than or equal to a nominal 10 micrometers (PM-10). In its submittal, the State also requested that EPA approve the maintenance plan for the area into the Illinois PM SIP. The redesignation request and maintenance plan meet the redesignation requirements of the Clean Air Act.

(j) Determination of Attainment. EPA has determined, as of November 27, 2009, that the Chicago-Gary-Lake County, IL-IN PM2.5 nonattainment area has attained the 1997 PM2.5 NAAQS. This determination, in accordance with 40 CFR 51.1004(c), suspends the requirements for this area to submit an attainment demonstration, associated reasonably available control measures, reasonable further progress, contingency measures, and other plan elements related to attainment of the standard for as long as this area continues to meet the 1997 PM2.5 NAAQS.

(k) Determination of attainment. EPA has determined, as of May 23, 2011, that the St. Louis (MO-IL) metropolitan 1997 PM2.5 nonattainment area has attained the 1997 PM2.5 NAAQS. This determination, in accordance with 40 CFR 51.1004(c), suspends the requirements for this area to submit an attainment demonstration, associated reasonably available control measures, reasonable further progress, contingency measures, and other plan elements related to attainment of the standards for as long as the area continues to meet the 1997 PM2.5 NAAQS. In addition, based upon review of the air quality data for the 3-year period 2007 to 2009, EPA has determined that the St. Louis (MO-IL) PM2.5 nonattainment area has attained the 1997 PM2.5 NAAQS by the applicable attainment date of April 5, 2010.

(l) Approval—The 1997 annual PM2.5 maintenance plan for the Illinois portion of the Chicago-Gary-Lake County, IL-IN nonattainment area (including Cook, DuPage, Kane, Lake, McHenry and Will Counties, Aux Sable and Goose Lake Townships in Grundy County, and Oswego Township in Kendall County) has been approved as submitted on October 15, 2010, and supplemented on September 16, 2011, and May 6, 2013. The maintenance plan establishes 2008 and 2025 motor vehicle emissions budgets for this area of 127,951 tons per year for NOX and 5,100 tons per year for primary PM2.5 in 2008 and 44,224 tons per year for NOX and 2,377 tons per year for primary PM2.5 in 2025.

(m) Illinois' 2002 NOX, primary PM2.5, SO2, ammonia, and VOC emission inventories, as submitted on October 15, 2010, and supplemented on May 6, 2013, satisfy the emission inventory requirements of section 172(c)(3) of the Clean Air Act for the Chicago area.

[45 FR 11493, Feb. 21, 1980, as amended at 46 FR 44185, Sept. 3, 1981; 47 FR 26620, June 21, 1982; 48 FR 45246, Oct. 4, 1983; 49 FR 1905, Jan. 16, 1984; 55 FR 20266, May 16, 1990; 61 FR 41345, Aug. 8, 1996; 63 FR 11846, Mar. 11, 1998; 63 FR 47434, Sept. 8, 1998; 64 FR 37851, July 14, 1999; 70 FR 55545, 55549, Sept. 22, 2005; 74 FR 62249, Nov. 27, 2009; 76 FR 29656, May 23, 2011; 77 FR 38184, June 27, 2012; 78 FR 60706, Oct. 2, 2013]

return arrow Back to Top

§52.726   Control strategy: Ozone.

(a) Part D—Conditional Approval—The Illinois plan is approved provided that the following conditions are satisfied:

(1) [Reserved]

(2) The State conducts a study to demonstrate that the 75 percent overall control efficiency requirement in Rule 205(n) represents RACT, submits the results of the study to USEPA, and submits any necessary regulations representing RACT to the Illinois Pollution Control Board. The State must comply with these conditions by February 28, 1981. Any necessary regulations must be finally promulgated by the State and submitted to USEPA by February 28, 1982.

(3) Extension of Condition—USEPA approves the date of July 31, 1984 for the State of Illinois to satisfy the condition of approval to the ozone State Implementation Plan listed in paragraph (a)(2) of this section.

(b) Disapproval—USEPA disapproves the compliance schedule in Rule 205(j) as it applies to loading rack controls for all emission sources subject to Rule 205(b)(1), as approved by USEPA on May 31, 1972 which were required to be in compliance by December 31, 1973. This disapproval does not in and of itself result in the growth restrictions of section 110(a)(2)(I).

(c) Negative Declarations—Stationary Source Categories. The State of Illinois has certified to the satisfaction of USEPA that no sources are located in the nonattainment areas of the State which are covered by the following Control Technique Guidelines:

(1) High density polyethylene and polypropylene manufacturers.

(2) Vegetable oil processing sources with volatile organic compound emissions equal to or greater than 100 tons per year.

(d) Part D Disapproval—The Administrator finds that Illinois' ozone plan for Cook, Lake, DuPage and Kane Counties, which was required to be submitted by July 1, 1982, does not satisfy all the requirements of Part D, Title I of the Clean Air Act and, thus, is disapproved. No major new stationary source, of major modification of a stationary source, or volatile organic compounds may be constructed in Cook, Lake, DuPage or Kane Counties, unless the construction permit application is complete on or before November 16, 1988. This disapproval does not affect USEPA's approval (or conditional approval) of individual parts of Illinois' ozone plan, and they remain approved.

(e) Disapproval—The Administrator finds that the following State rules have not been demonstrated to be consistent with the reasonably available control technology requirements of section 172 of the Clean Air Act, as amended in 1977, and thus, are disapproved: subpart F, section 215.204(c); subpart F, section 215.206(b); subpart F, section 215.204(j)(4); subpart I; subpart AA; subpart PP; subpart QQ; subpart RR; subpart A, section 215.102; subpart T; subpart H, section 215.245; subpart F, section 215.207; and subpart A, section 215.107, all of title 35; Environmental Protection; subtitle B: Air Pollution; Chapter 1: Pollution Control Board of the Illinois Administrative Code (June 1989).

(f) On September 30, 1992, the State submitted rules regulating volatile organic compound emissions from gasoline dispensing facilities' motor vehicle fuel operations (Stage II vapor recovery rules) in the Chicago ozone nonattainment area. The Illinois Environmental Protection Agency Bureau of Air must as part of the program conduct inspections of facilities subject to this rule to ensure compliance with the applicable rules. These inspections will be conducted on an annual basis or an alternative schedule as approved in the USEPA Fiscal Year Inspection Program Plan.

(g) Approval—The Administrator approves the incorporation of the photochemical assessment ambient monitoring system submitted by Illinois on November 4, 1993, into the Illinois State Implementation Plan. This submittal satisfies 40 CFR 58.20(f) which requires the State to provide for the establishment and maintenance of photochemical assessment monitoring stations (PAMS) by November 12, 1993.

(h) Approval—On November 12, 1993, the Illinois Environmental Protection Agency submitted an ozone redesignation request and maintenance plan for Jersey County ozone nonattainment area and requested that Jersey County be redesignated to attainment for ozone. The redesignation request and maintenance plan meet the redesignation requirements in section 107(d)(3)(d) of the Act. The redesignation meets the Federal requirements of section 182(a)(1) of the Clean Air Act as a revision to the Illinois ozone State Implementation Plan for Jersey County.

(i) The base year (1990) ozone emission inventory requirement of section 182(a)(1) of the Clean Air Act, as amended in 1990, has been satisfied for the following Illinois ozone nonattainment areas: the Chicago nonattainment area—Cook, DuPage, Kane, Lake, Will and McHenry Counties, Aux Sable and Gooselake Townships in Grundy County, and Oswego Township in Kendall County; the Metro-East St. Louis nonattainment area—Madison, Monroe, and St. Clair Counties; and Jersey County.

(j) Approval—On July 14, 1994, Illinois submitted two of three elements required by section 182(d)(1)(A) of the Clean Air Amendments of 1990 to be incorporated as part of the vehicle miles traveled (VMT) State Implementation Plan intended to offset any growth in emissions from a growth in vehicle miles traveled. These elements are the offsetting of growth in emissions attributable to growth in VMT which was due November 15, 1992, and, transportation control measures (TCMs) required as part of Illinois' 15 percent reasonable further progress (RFP) plan which was due November 15, 1993. Illinois satisfied the first requirement by projecting emissions from mobile sources and demonstrating that no increase in emissions would take place. Illinois satisfied the second requirement by submitting the TCMs listed in Table 1 which are now approved into the Illinois SIP.

Table 1

Project type Location description Completion status SIP credit VOC tpd
RS/SIG MODMadison Street (Western Ave. to Halsted Street)Done0.015400
SIG COORDWillow Road (Landwer Road to Shermer)Awarded0.052000
SIG COORDRand Road (Baldwin Road to Kennicott)Awarded0.052000
SIG COORDNorthwest Hwy (Potter Road to Cumberland Avenue)Awarded0.030000
SIGS/SIG COORD159th Street (US 45 to 76th Ave & at 91st Avenue)Awarded0.030000
SIG COORDHarlem Ave. (71st St. to 92nd)Awarded0.052000
SIG COORDHarlem Ave. (99th Street to 135th St.)Awarded0.052000
RECONST/SIGS/LTSArcher Ave. (88th Ave to 65th St.)Awarded0.030000
SIG COORDOgden Ave. (N. Aurora Road to Naper Boulevard)Awarded0.030000
SIG COORDNorth Ave. (Tyler to Kautz)Awarded0.030000
SIG COORDHiggens Road (Il 72 at Il 31)Awarded0.030000
SIG COORDSheridan Road (Il 173 to Wadsworth)Awarded0.030000
SIG COORDLagrange Road (Belmont to Lake St.)Awarded0.030000
SIG COORDDundee Road (Sanders Road to Skokie Valley Road)Awarded0.052000
SIG COORDDundee Road (Buffalo Grove Road to Il 21)Awarded0.030000
INT IMP/SIG COORDGolf Road (E. River Road to Washington Ave.)Awarded0.052000
SIG COORDGolf Road (Barrington to Roselle Road)Awarded0.030000
SIG COORDHiggins Road (Barrington to Roselle Road)Awarded0.030000
SIG COORDJoe Orr Road (Vincennes Ave. to Il 1)Awarded0.030000

Table 1

Project type Location description Completion status SIP credit
SIG COORD/RSCrawford Ave. (93rd Street to 127th Street)Awarded0.052000
SIG COORDIL 53 (Briarcliff to South of I-55)Done0.030000
SIG COORDOgden Ave. (Oakwood Avenue to Fairview Avenue)Awarded0.019000
SIG COORDUS 14 (Rohlwing Road to Wilke Road)Awarded0.030000
SIG COORDUS 30 (At Cottage Grove, Ellis St)Awarded0.030000
SIG COORDIL 53 (Modonough to Mills)Done0.030000
SIG CONNOgden Ave. (IL 43 to 31st Street)Awarded0.013000
SIG CONNUS 12 (Long Grove—Hicks Road)Awarded0.055200
SIG CONNNorth Ave. (Oak Park to Ridgeland)Awarded0.007000
SIG CONNRoosevelt Road (Westchester Bl—IL 43)Awarded0.137000
SIG CONNDepster St (Keeler to Crawford Ave.)Awarded0.010000
SIG CONNArlington Hgts Rd. (Thomas to Central)Awarded0.044000
SIG CONNPalatine Rd. (Shoenbeck to Wolf Roads)Awarded0.042500
SIG CONNWestern Ave. (US 30—Lakewood)Awarded0.018900
RS/INT IMPNorth Ave. (I-290 to IL 43)Awarded0.056100
INT IMPPlum Grove Rd. (At Higgins Road)Awarded0.010700
INT IMPSt Street (At Illinois)Awarded0.002700
RS/SIG MOD/INT IMPIllinois/Grand (Kingsbury to Lake Shore Drive)Done0.004200
ADD TURN LANESYork Rd. (Industrial to Grand Ave.)Done0.003800
SERVICE IMPSW Route Lane ServiceScheduled0.005516
SIG INTCONNWashington StreetScheduled0.030370
SIG INTCONNIL 59Scheduled0.068650
ENGRCitywide—Naperville0.086230
SIG INTCONNWashington StreetScheduled0.008230
SIG INTCONNLewis Ave. (Yorkhousse to ILL 173)Scheduled0.034600
SIG INTCONNSchaumberg Rd. (Barrington to Martingale)Scheduled0.078080
Vanpool Program (94 vehicles)Region-Wide SuburbanDone0.134000
Transp. CenterNorth West Cook CountyDone0.032835
Transp. CenterSears T.F.Done0.005805
StationClark/LakeDone0.010000
Station Recon18Th Douglas LineDone0.001500
Station ReconLindenDone0.001500
Station ReconCottage GroveDone0.001300
Com. PkgLisleDone0.010177
Com. PkgJefferson ParkDone0.000110
Com. PkgEdison ParkDone0.003614
Com. PkgPalatineDone0.004336
Com. PkgCentral StreetDone0.000519
Com. PkgPalatineDone0.004890
Com. PkgCrystal LakeDone0.034948
Com. Pkg137Th/RiverdaleDone0.004565
Com. PkgRiver ForestDone0.000289
Com. Pkg115Th/KensingtonDone0.002795
Com. Pkg119Th StDone0.004483
Com. PkgWilmetteDone0.001587
Com. Pkg111Th StDone0.000507
Com. PkgEdison ParkDone0.002371
Com. PkgJolietDone0.003967
Com. PkgHanover ParkDone0.021799
Com. PkgBartlettDone0.008911
Com. PkgChicago RidgeDone0.002159
Com. Pkg103 Rd StDone0.000675
Com. PkgElmhurstDone0.003857
Com. PkgBartlettDone0.009326
Com. PkgMorton GroveDone0.001444
Com. PkgPalatineDone0.003598
Com. PkgHarvardDone0.006299
Com. PkgWillow SpringsDone0.001200
Com. PkgEdgebrookDone0.002240
Com. PkgBensenvilleDone0.002010
Com. PkgHanover ParkDone0.015020
Com. PkgMidlothianDone0.002570
Com. PkgRoute 59Done0.025020
Com. PkgLake Forest (West)Done0.013780
Com. PkgLombardDone
Com. PkgElmhurstDone0.001010
Com. PkgWoodstockDone0.019000
Com. PkgUniversity ParkDone0.019950
Com. PkgGrayslakeDone0.006210
Com. PkgOak ForestDone0.004260
Com. Pkg91 St St.Done0.003380
Com. PkgLockportDone0.007360
Com. PkgRavenswoodDone0.000130
Com. PkgHickory CreekDone0.060140
Com. PkgCaryDone0.005980
Com. PkgBlue IslandDone0.019430
Com. PkgLemontDone0.016200
Com. PkgItascaDone0.003860
Com. PkgMaywoodDone0.000600
Com. PkgIvanhoeDone0.001960
Com. PkgRaviniaDone0.003210
Com. PkgFox River GroveDone0.025170
Com. PkgMedinahDone0.012250
Com. PkgHanover ParkDone0.011840
Com. PkgWorthDone0.003530
Com. PkgRoselleDone0.007710
Com. PkgCrystal LakeDone0.015050
Com. PkgGreshamDone0.000300
Com. PkgBarringtonDone0.002420
Rideshare Prog.RegionwideScheduled0.040000
Rapid Transit ServiceMidway AirportDone0.220000
Transp. CenterDeerfield Lake-CookDone0.004160
Station ReconDavis St.Done0.004000
Station ReconAddisonDone0.004000
Station ReconKing DriveDone0.003000
Station ReconWashington/WellsDone0.003000
Com. PkgCaryDone0.027910
Com. PkgMorton GroveDone0.002460
Com. Pkg80th Ave.Scheduled0.043200
Com. PkgRound LakeDone0.015150
Com. PkgGrayslakeDone0.009170
Com. PkgInglesideScheduled0.005430
Com. PkgSchamburgScheduled0.042090
Com. PkgOak ForestScheduled0.004680
Com. PkgLake CookScheduled0.026390
Com. PkgGrayslakeScheduled0.035290

(k) Approval—EPA is approving the section 182(f) oxides of nitrogen (NOX) reasonably available control technology (RACT), new source review (NSR), vehicle inspection/maintenance (I/M), and general conformity exemptions for the Illinois portion of the Chicago-Gary-Lake County severe ozone nonattainment area as requested by the States of Illinois, Indiana, Michigan, and Wisconsin in a July 13, 1994 submittal. This approval does not cover the exemption of NOX transportation conformity requirements of section 176(c) for this area. Approval of these exemptions is contingent on the results of the final ozone attainment demonstration expected to be submitted in mid-1997. The approval will be modified if the final attainment demonstration demonstrates that NOX emission controls are needed in the nonattainment area to attain the ozone standard in the Lake Michigan Ozone Study modeling domain.

(l) Approval—The United States Environmental Protection Agency is approving under section 182(b)(1) of the Clean Air Act the exemption of the Chicago severe, ozone nonattainment area from the build/no-build and less than-1990 interim transportation conformity oxides of nitrogen requirements as requested by the State of Illinois in a June 20, 1995 submittal. In light of the modeling completed thus far and considering the importance of the OTAG process and attainment plan modeling efforts, USEPA grants this NOX waiver on a contingent basis. As the OTAG modeling results and control recommendations are completed in 1996, this information will be incorporated into attainment plans being developed by the LADCO States. When these attainment plans are submitted to USEPA in mid-1997, these new modeling analyses will be reviewed to determine if the NOX waiver should be continued, altered, or removed. USEPA's rulemaking action to reconsider the initial NOX waiver may occur simultaneously with rulemaking action on the attainment plans. The USEPA also reserves the right to require NOX emission controls for transportation sources under section 110(a)(2)(D) of the Act if future ozone modeling demonstrates that such controls are needed to achieve the ozone standard in downwind areas. The Chicago severe ozone nonattainment area includes the Counties of Cook, DuPage, Grundy (Aux Sable and Gooselake Townships), Kane, Kendall (Oswego Township), Lake, McHenry, and Will.

(m) [Reserved]

(n) Negative declaration—Shipbuilding and ship repair industry. On October 11, 1996, the State of Illinois certified to the satisfaction of the United States Environmental Protection Agency that no major sources categorized as part of the shipbuilding and ship repair industry are located in the Chicago, Illinois ozone nonattainment area which is comprised of Cook, DuPage, Kane, Lake, McHenry, Will Counties and Aux Sable and Goose Lake Townships in Grundy County and Oswego Township in Kendall County or the Metro-East, Illinois ozone nonattainment area which is comprised of Madison, Monroe, and St. Clair Counties.

(o) Negative declaration—Aerospace manufacturing and rework industry. On October 11, 1996, the State of Illinois certified to the satisfaction of the United States Environmental Protection Agency that no major sources categorized as part of the Aerospace Manufacturing and Rework Industry are located in the Chicago, Illinois ozone nonattainment area which is comprised of Cook, DuPage, Kane, Lake, McHenry, Will Counties and Aux Sable and Goose Lake Townships in Grundy County and Oswego Township in Kendall County or the Metro-East, Illinois ozone nonattainment area which is comprised of Madison, Monroe, and St. Clair Counties.

(p) Approval—On November 15, 1993, Illinois submitted 15 percent rate-of-progress and 3 percent contingency plans for the Chicago ozone nonattainment area as a requested revision to the Illinois State Implementation Plan. These plans satisfy sections 182(b)(1), 172(c)(9), and 182(c)(9) of the Clean Air Act, as amended in 1990.

(q) Approval—On November 15, 1993, Illinois submitted 15 percent rate-of-progress and 3 percent contingency plans for the Metro-East St. Louis ozone nonattainment area as a requested revision to the Illinois State Implementation Plan. These plans satisfy sections 182(b)(1) and 172(c)(9) of the Clean Air Act, as amended in 1990.

(r) Approval—On November 15, 1993, Illinois submitted the following transportation control measures as part of the 15 percent rate-of-progress and 3 percent contingency plans for the Metro-East ozone nonattainment area: Work trip reductions; transit improvements; and traffic flow improvements.

(s) On October 10, 1997, Illinois submitted a site-specific revision to the State Implementation Plan, in the form of a letter from Bharat Mathur, Chief, Bureau of Air, Illinois Environmental Protection Agency. This October 10, 1997, letter requests a change in regulatory status for Riverside Laboratories, Inc.'s Kane County facility, to reflect that the Federal site-specific rule for Riverside (40 CFR 52.741(e)(10)) has been superseded by the State of Illinois regulations, including the emission limits in 35 Illinois Administrative Code 218.204(c) and the associated control requirements, test methods and recordkeeping requirements in Part 218 and the associated definitions in part 211. These State regulations shall become the federally approved regulations applicable to Riverside on August 31, 1998. The site-specific rule, applicable to Riverside, promulgated by the Environmental Protection Agency on August 21, 1995 (40 CFR 52.741(e)(10)), remains in effect and is enforceable after August 31, 1998 for the period before August 31, 1998.

(t) The Illinois volatile organic compound (VOC) rules that apply to the Stepan Company Millsdale Plant for volatile organic liquid storage (35 Ill. Admin. Code Part 218, Subpart B), batch processing (35 Ill. Admin. Code Parts 218 and 219, Subpart V) and continuous reactor and distillation processes (35 Ill. Admin. Code Part 218, Subpart Q) were approved by the United States Environmental Protection Agency (USEPA) on August 8, 1996, April 2, 1996, and June 17, 1997, respectively. Because these rules have been approved into the State Implementation Plan and represent reasonably available control technology for VOC, USEPA revokes the June 29, 1990 Federal Implementation Plan as it applies to Stepan and replaces it with Illinois' volatile organic liquid storage, batch process, and continuous reactor and distillation process rules.

(u) Negative declaration—Industrial wastewater category. On October 2, 1998, the State of Illinois certified to the satisfaction of the United States Environmental Protection Agency that no major sources categorized as part of the Industrial wastewater category are located in the Metro-East ozone nonattainment area (Metro-East). The Metro-East area is comprised of Madison, Monroe and St. Clair Counties which are located in southwest Illinois, adjacent to St. Louis, Missouri.

(v) Negative declaration—Industrial cleaning solvents category. On October 2, 1998, the State of Illinois certified to the satisfaction of the United States Environmental Protection Agency that no major sources categorized as part of the Industrial cleaning solvents category are located in the Metro-East ozone nonattainment area (Metro-East). The Metro-East area is comprised of Madison, Monroe and St. Clair Counties which are located in southwest Illinois, adjacent to St. Louis, Missouri.

(w) Approval—On December 18, 1997, December 17, 1999, January 14, 2000, and January 21, 2000, Illinois submitted a post-1996 Rate Of Progress Plan for the Chicago ozone nonattainment area as a requested revision to the Illinois State Implementation Plan. This plan reduces ozone precursor emissions by 9 percent from 1990 baseline emissions by November 15, 1999. This plan also supports a mobile source emissions budget of 279.3 tons/day of volatile organic compounds for transportation conformity purposes.

(x) Approval—On December 18, 1997, Illinois submitted a contingency measure plan as part of the Chicago Area post-1996 Rate of Progress Plan. This plan reduces volatile organic compound emissions in the Chicago ozone nonattainment area by 3 percent from 1990 baseline emissions by November 15, 1999.

(y) Approval—On December 18, 1997, Illinois submitted Transportation Control Measures (TCMs) as part of the post-1996 Rate Of Progress Plan for the Chicago ozone nonattainment area. The TCMs being approved are listed in the following documents published by the Chicago Area Transportation Study: “Transportation Control Measures Contribution to the Post-1996 Rate-Of-Progress State Implementation Plan,” March 22, 1996; “Transportation Control Measures Contribution to the 9 percent Control Strategy State Implementation Plan,” June 11, 1998; and “1999 Transportation Control Measures Contribution to the 9 percent Rate of Progress Control Strategy State Implementation Plan,” December 9, 1999.

(z) Negative declaration—Industrial cleaning solvents category. On December 23, 1999, the State of Illinois certified to the satisfaction of the United States Environmental Protection Agency that no major sources categorized as part of the industrial cleaning solvents category are located in the Chicago ozone nonattainment area. The Chicago ozone nonattainment area includes Cook County, DuPage County, Aux Sable and Goose Lake Townships in Grundy County, Kane County, Oswego Township in Kendall County, Lake County, McHenry County and Will County.

(aa) Negative declaration—Industrial wastewater category. On December 23, 1999, the State of Illinois certified to the satisfaction of the United States Environmental Protection Agency that no major sources categorized as part of the Industrial Wastewater Category are located in the Chicago ozone nonattainment area. The Chicago ozone nonattainment area includes Cook County, DuPage County, Aux Sable and Goose Lake Townships in Grundy County, Kane County, Oswego Township in Kendall County, Lake County, McHenry County and Will County.

(bb) Approval—Revisions to the SIP submitted by Illinois on November 15, 1999; February 10, 2000; April 13, 2001; and April 30, 2001. The revisions are for the purpose of satisfying the attainment demonstration requirements of section 182(c)(2)(A) of the Act for the Metro-East St. Louis area. The revision establishes an attainment date of November 15, 2004, for the St. Louis moderate ozone nonattainment area. This revision establishes MVEBs for 2004 of 26.62 TPD of VOC and 35.52 TPD of NOX to be used in transportation conformity in the Metro-East St. Louis area until revised budgets pursuant to MOBILE6 are submitted and found adequate. In the revision, Illinois commits to revise its VOC and NOX transportation conformity budgets within two years of the release of MOBILE6. No conformity determinations will be made during the second year following the release of MOBILE6 unless and until the MVEBs have been recalculated using MOBILE6 and found adequate by EPA. EPA is granting a waiver for the Metro East St. Louis area to the state of Illinois from the NOX RACT requirements of the Act and disapproving the request for a waiver from the NOX NSR and NOX general conformity requirements. EPA is finding that the Contingency Measures identified by Illinois are adequate to meet the requirements of the Act. EPA finds that the Illinois SIP meets the requirements pertaining to RACM under the Act for the Metro-East St. Louis area.

(cc) Approval—Illinois has adopted and USEPA has approved sufficient NOX emission regulations to assure that it will achieve the level of NOX emissions budgeted for the State by USEPA. USEPA has made two minor budget revisions requested by Illinois, adding a boiler owned by LTV Steel and deleting a boiler owned by the University of Illinois from the inventory of large NOX sources.

(dd) Chicago Ozone Attainment Demonstration Approval—On December 26, 2000, Illinois submitted a one-hour ozone attainment demonstration plan as a requested revision to the Illinois State Implementation Plan. This plan includes: A modeled demonstration of attainment and associated attainment year conformity emission budgets; a plan to reduce ozone precursor emissions by 3 percent per year from 2000 to 2007 (a post-1999 rate-of-progress plan), and associated conformity emission budgets; a contingency measures plan for both the ozone attainment demonstration and the post-1999 rate-of-progress plan; a commitment to conduct a Mid-Course Review of the ozone attainment demonstration by the end of 2004; a demonstration that Illinois has implemented all reasonably available control measures; and a commitment to revise motor vehicle emission budgets within two years after the U.S. Environmental Protection Agency officially releases the MOBILE6 emission factor model.

(ee) Approval of the Maintenance Plan for the Illinois Portion of the St. Louis Area—On December 30, 2002 Illinois submitted Maintenance Plan for the Illinois portion of the St. Louis Nonattainment Area. The plan includes 2014 On-Road Motor Vehicle Emission Budget of 10.13 tons per ozone season weekday of VOCs and 18.72 tons per ozone season weekday NOX to be used in transportation conformity.

(ff) Approval—On April 11, 2003, Illinois submitted a revision to the ozone attainment plan for the Chicago severe 1-hour ozone nonattainment area. This plan revised the 2005 and 2007 Motor Vehicle Emissions Budgets (MVEB) recalculated using the emissions factor model MOBILE6. The approved motor vehicle emissions budgets are 151.11 tons per day VOC for 2005 and 127.42 tons per day VOC and 280.4 tons per day NOX for 2007.

(gg) Approval—On January 30, 2007, the Illinois Environmental Protection Agency (IEPA) requested that EPA find that the Illinois portion of the Chicago-Gary-Lake County, Illinois-Indiana (IL-IN) nonattainment area, attained the revoked 1-hour ozone National Ambient Air Quality Standard (NAAQS). After review of this submission, EPA approves this finding.

(hh) Disapproval. EPA is disapproving 35 Illinois Administrative Code part 217, subpart X, Voluntary NOX Emissions Reduction Program, as a revision to the Illinois SIP.

(ii) Approval. EPA is approving a July 29, 2010, request from the State of Illinois for a waiver from the Clean Air Act requirement for Oxides of Nitrogen (NOx) Reasonably Available Control Technology (RACT) in the Illinois portions of the Chicago-Gary-Lake County, Illinois-Indiana (Cook, DuPage, Kane, Lake, McHenry, and Will Counties, and portions of Grundy (Aux Sable and Goose Lake Townships) and Kendall (Oswego Township) Counties in Illinois) and St. Louis, Missouri-Illinois (Jersey, Madison, Monroe, and St. Clair Counties in Illinois) 1997 8-hour ozone nonattainment areas.

(jj) Determination of attainment. On June 5, 2009, the state of Indiana requested that EPA find that the Indiana portion of the Chicago-Gary-Lake County, Illinois-Indiana (IL-IN) ozone nonattainment area has attained the 1997 8-hour ozone National Ambient Air Quality Standard (NAAQS). After review of Indiana's submission and 2006-2008 ozone air quality data for this ozone nonattainment area, EPA finds that the entire Chicago-Gary-Lake County, IL-IN area has attained the 1997 8-hour ozone NAAQS. Therefore, EPA has determined, as of March 12, 2010, that Cook, DuPage, Kane, Lake, McHenry, and Will Counties, and portions of Grundy County (Aux Sable and Goose Lake Townships) and Kendall County (Oswego Township) in Illinois have attained the 1997 8-hour ozone standard.

(kk) Determination of attainment. EPA has determined, as of June 9, 2011, that the St. Louis (MO-IL) metropolitan 1997 8-hour ozone nonattainment area has attained the 1997 8-hour ozone NAAQS. This determination, in accordance with 40 CFR 51.918, suspends the requirements for this area to submit an attainment demonstration, associated reasonably available control measures, reasonable further progress, contingency measures, and other plan elements related to attainment of the standards for as long as the area continues to meet the 1997 Ozone NAAQS. In addition, based upon EPA's review of the air quality data for the 3-year period 2007 to 2009, the St. Louis (MO-IL) ozone nonattainment area has attained the 1997 8-hour ozone NAAQS by the applicable attainment date of June 15, 2010.

(ll) Approval—On May 26, 2010, and September 16, 2011, Illinois submitted a request to redesignate the Illinois portion of the St. Louis, MO-IL area to attainment of the 1997 8-hour ozone standard. The St. Louis area includes Jersey, Madison, Monroe, and St. Clair Counties in Illinois and St. Louis City and Franklin, Jefferson, St. Charles and St. Louis Counties in Missouri. As part of the redesignation request, the State submitted a plan for maintaining the 1997 8-hour ozone standard through 2025 in the area as required by section 175A of the Clean Air Act. Part of the section 175A maintenance plan includes a contingency plan. The ozone maintenance plan establishes 2008 motor vehicle emissions budgets for the Illinois portion of the St. Louis area of 17.27 tpd for volatile organic compounds (VOC) and 52.57 tpd for nitrogen oxides (NOX). In addition the maintenance plan establishes 2025 motor vehicle emissions budgets for the Illinois portion of the St. Louis area of 5.68 tpd for VOC and 15.22 tpd for NOX.

(mm) Emissions inventories for the 1997 8-hour ozone standard

(1) Approval—Illinois' 2002 emissions inventory satisfies the emissions inventory requirements of section 182(a)(1) of the Clean Air Act for the Illinois portion of the St. Louis, MO-IL area under the 1997 8-hour ozone standard.

(2) Approval—Illinois' 2002 volatile organic compounds and nitrogen oxides emission inventories satisfy the emissions inventory requirements of section 182(a)(1) of the Clean Air Act for the Illinois portion of the Chicago-Gary-Lake County, Illinois-Indiana area under the 1997 8-hour ozone standard.

(nn) Approval—On July 23, 2009, and September 16, 2011, Illinois submitted a request to redesignate the Illinois portion of the Chicago-Gary-Lake County, Illinois-Indiana area to attainment of the 1997 8-hour ozone standard. The Illinois portion of the Chicago-Gary-Lake County, Illinois-Indiana area includes Cook, DuPage, Kane, Lake, McHenry, and Will Counties and portions of Grundy (Aux Sable and Goose Lake Townships) and Kendall (Oswego Township) Counties. As part of the redesignation request, the State submitted a plan for maintaining the 1997 8-hour ozone standard through 2025 in the area as required by section 175A of the Clean Air Act. Part of the section 175A maintenance plan includes a contingency plan. The ozone maintenance plan establishes 2008 motor vehicle emissions budgets for the Illinois portion of the Chicago-Gary-Lake County, Illinois-Indiana area of 117.23 tons per day (tpd) for volatile organic compounds (VOC) and 373.52 tpd for nitrogen oxides (NOX). In addition, the maintenance plan establishes 2025 motor vehicle emissions budgets for the Illinois portion of the Chicago-Gary-Lake County, Illinois-Indiana area of 48.13 tpd for VOC and 125.27 tpd for NOX.

(oo) Approval—On March 28, 2014, the State of Illinois submitted a revision to its State Implementation Plan for the Illinois portion of the Chicago-Gary-Lake County, Illinois-Indiana area (the Greater Chicago Area). The submittal established new Motor Vehicle Emissions Budgets (MVEB) for Volatile Organic Compounds (VOC) and Oxides of Nitrogen (NOX) for the year 2025. The MVEBs for the Illinois portion of the Greater Chicago Area are: 60.13 tons/day of VOC emissions and 150.27 tons/day of NOX emissions for the year 2025.

(pp) On September 3, 2014, Illinois submitted 2011 volatile organic compounds and oxides of nitrogen emission inventories for the Illinois portions of the Chicago-Naperville, Illinois-Indiana-Wisconsin and St. Louis, Missouri-Illinois nonattainment areas for the 2008 ozone national ambient air quality standard as a revision of the Illinois state implementation plan. The emission inventories are approved as a revision of the state's implementation plan.

(qq) Determination of attainment. As required by section 181(b)(2)(A) of the Clean Air Act, EPA has determined that the St. Louis, MO-IL marginal 2008 ozone nonattainment area has attained the NAAQS by the applicable attainment date of July 20, 2016.

[45 FR 55197, Aug. 19, 1980]

Editorial Note: For Federal Register citations affecting §52.726, see the List of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and at www.govinfo.gov.

return arrow Back to Top

§52.727   [Reserved]

§52.728   Control strategy: Nitrogen dioxide. [Reserved]

§52.729   [Reserved]

§52.730   Compliance schedules.

(a) The requirements of §51.262(a) of this chapter are not met since compliance schedules with adequate increments of progress have not been submitted for every source for which they are required.

(b) Federal compliance schedules. (1) Except as provided in paragraph (b)(3) of this section, the owner or operator of any stationary source subject to the following emission limiting regulations in the Illinois implementation plan shall comply with the applicable compliance schedule in paragraph (b)(2) of this section: Illinois Air Pollution Control Regulations Rule 203(d)(4), 203(d)(6)(B)(ii)(bb), 203(g)(1)(B), 203(g)(2), 203(g)(3), 203(g)(4), 204(c)(1)(A), 204(c)(2), 204(d), and 204(e).

(2) Compliance schedules. (i) The owner or operator of any stationary source subject to Illinois Air Pollution Control Regulation Rule 203(d)(4) shall take the following actions with respect to the source no later than the date specified.

(a) September 30, 1973—Advertise for bids for purchase and construction or installation of equipment, or for materials requisite for process modification sufficient to control particulate emissions from the source.

(b) November 15, 1973—Award contracts for emission control systems or process modification, or issue orders for the purchase of component parts to accomplish emission control or process modification.

(c) May 31, 1974—Initiate onsite construction or installation of emission control system or process modification.

(d) March 31, 1975—Complete onsite construction or installation of emission system or process modification.

(e) May 31, 1975—Complete shakedown operation and performance test on source, submit performance test results to the Administrator; achieve full compliance with State agency regulation.

(ii) The owner or operator of any stationary source subject to Illinois Air Pollution Control Regulation Rule 203(d)(6)(B)(ii)(bb) shall take the following actions with respect to the source no later than the date specified.

(a) September 30, 1973—Advertise for bids for purchase and construction or for modification of equipment sufficient to control particulate emissions from the source.

(b) November 15, 1973—Award contracts for emissions control systems or process modification, or issue orders for the purchase of component parts to accomplish emission control or process modification.

(c) March 31, 1974—Initiate onsite construction or installation of emission control system.

(d) October 31, 1974—Complete onsite construction or installation of emission control system.

(e) December 31, 1974—Achieve final compliance with Illinois Air Pollution Control Regulations Rule 203(d)(6)(B)(ii)(bb).

(iii) (a) The owner or operator of any boiler or furnace of more than 250 million BTU per hour heat input subject to Illinois Air Pollution Control Regulation Rule 204(c)(1)(A), 204(c)(2), 204(d), and 204(e) shall notify the Administrator, no later than October 1, 1973, of his intent to utilize either low-sulfur fuel or stack gas desulfurization to the requirements of said regulation.

(b) Any owner or operator of a stationary source subject to paragraph (b)(2)(iii)(a) of this section who elects to utilize low sulfur fuel shall take the following actions with respect to the source no later than the date specified.

(1) November 1, 1973—Submit to the Administrator a projection of the amount of fuel, by types, that will be substantially adequate to enable compliance with Illinois Air Pollution Control Regulations Rule 204(c)(1)(A), 204(c)(2), 204(d), and 204(e) on May 31, 1975, and for at least one year thereafter.

(2) December 31, 1973—Sign contracts with fuel suppliers for fuel requirements as projected above.

(3) January 31, 1974—Submit a statement as to whether boiler modifications will be required. If modifications will be required, submit plans for such modifications.

(4) March 15, 1974—Let contracts for necessary boiler modifications, if applicable.

(5) June 15, 1974—Initiate onsite modifications, if applicable.

(6) March 31, 1975—Complete onsite modifications, if applicable.

(7) May 31, 1975—Final compliance with the emission limitation of Rules 204(c)(1)(A), 204(c)(2), 204(d), and 204(e).

(c) Any owner or operator of a fuel combustion source subject to paragraph (b)(2)(iii)(a) of this section who elects to utilize stack gas desulfurization shall take the following actions with respect to the source no later than the date specified.

(1) November 1, 1973—Let necessary contracts for construction.

(2) March 31, 1974—Initiate onsite construction.

(3) March 31, 1975—Complete onsite construction.

(4) May 31, 1975—Complete shakedown operations and performance test on source, submit performance test results to the Administrator; achieve full compliance with Rule 204(c)(1)(A), 204(c)(2), 204(d), and 204(e).

(iv) (a) The owner or operator of any stationary source subject to Illinois Air Pollution Control Regulations Rule 203(g)(1)(B), 203(g)(2), 203(g)(3), and 203(g)(4) shall notify the Administrator, no later than October 1, 1973, of his intent to utilize either low ash fuel or a stack gas cleaning system to meet the requirements of said regulation.

(b) Any owner or operator of a stationary source subject to paragraph (b)(2)(iv)(a) of this section who elects to utilize low ash fuel shall take the following actions with respect to the source no later than the date specified.

(1) November 1, 1973—Submit to the Administrator a projection of the amount of fuel, by types, that will be substantially adequate to enable compliance with Illinois Air Pollution Control Regulations Rule 203(g)(1)(B), 203(g)(2), 203(g)(3), and 203(g)(4) on May 31, 1975, and for at least one year thereafter.

(2) December 31, 1973—Sign contracts with fuel suppliers for fuel requirements as projected above.

(3) January 31, 1974—Submit a statement as to whether boiler modifications will be required. If modifications will be required, submit plans for such modifications.

(4) March 15, 1974—Let contracts for necessary boiler modifications, if applicable.

(5) June 15, 1974—Initiate onsite modifications, if applicable.

(6) March 31, 1975—Complete onsite modifications, if applicable.

(7) May 31, 1975—Final compliance with the emission limitation of Rule 203(g)(1)(B), 203(g)(2), 203(g)(3), and 203(g)(4).

(c) Any owner or operator of a stationary source subject to paragraph (b)(2)(iv)(a) of this section who elects to utilize a stack gas cleaning system shall take the following actions with respect to the source no later than the date specified.

(1) January 15, 1974—Let necessary contracts for construction.

(2) April 1, 1974—Initiate onsite construction.

(3) April 1, 1975—Complete onsite construction.

(4) May 31, 1975—Complete shakedown operations and performance tests on source, submit performance test results to the Administrator; achieve full compliance with Rule 203(g)(1)(B), 203(g)(2), 203(g)(3), and 203(g)(4).

(v) Ten days prior to the conduct of any performance test required by this paragraph, the owner or operator of the affected source shall give notice of such test to the Administrator to afford him the opportunity to have an observer present.

(vi) Any owner or operator subject to a compliance schedule above shall certify to the Administrator, within five days after the deadline for each increment of progress in that schedule, whether or not the increment has been met.

(3)(i) None of the above paragraphs shall apply to a source which is presently in compliance with applicable regulations and which has certified such compliance to the Administrator by October 1, 1973. The Administrator may request whatever supporting information he considers necessary for proper certification.

(ii) Any compliance schedule adopted by the State and approved by the Administrator shall satisfy the requirements of this paragraph for the affected source.

(iii) Any owner or operator subject to a compliance schedule in this paragraph may submit to the Administrator no later than October 1, 1973, a proposed alternative compliance schedule. No such compliance schedule may provide for final compliance after the final compliance date in the applicable compliance schedule of this paragraph. If promulgated by the Administrator, such schedule shall satisfy the requirements of this paragraph for the affected source.

(4) Nothing in this paragraph shall preclude the Administrator from promulgating a separate schedule for any source to which the application of the compliance schedules in paragraph (b)(2) of this section fail to satisfy the requirements of §§51.261 and 51.262(a) of this chapter.

(c) [Reserved]

(d) The compliance schedules for the sources identified below are disapproved as not meeting the requirements of subpart N of this chapter. All regulations cited are air pollution control regulations of the State, unless otherwise noted.

SourceLocationRegulation involvedDate schedule adopted
christian county
Allied Mills, IncTaylorville204(c)Feb. 28, 1973.
cook county
Harco Aluminum IncChicago204(c)Dec. 9, 1973.
J. L. Clark Manufacturing CoDowners Grove205(f)May 4, 1973.
Johnson & JohnsonBedford Park205(f)Jun. 20, 1973.
Lloyd J. Harris Pie, Co. IncChicago204(c)Feb. 27, 1973.
Union Oil Co. of California
   (a) No. 10 boiler
......do204(c)Jun. 19, 1973,
Dec. 13, 1973.
   (b) 11BIA crude heater
W. H. Hutchingson & Son, Inc......do205(f)Aug. 12, 1973.
Western Rust Proof Co......do204(c)Oct. 10, 1973.
Wheeler Uniform Service Inc......do204(c)May 22, 1973.
Wm. Yuenger Manufacturing Co......do204(c)Aug. 16, 1973.
World's Finest Chocolate Inc......do204(c)May 30, 1973.
jackson county
Tuck Industries, IncCarbondale204(c)Jun. 20, 1973.
kane county
All Steel Equipment CorpMontgomery204(f)July 24, 1973.
Consolidated Food IncAurora205(f)May 9, 1973.
lake county
Morton Manufacturing CoLibertyville205(f)Aug. 27, 1973.
la salle county
Allied Mills IncMendota204(c)May 28, 1973.
madison county
Clark Oil & Refining CorpHartford204(f)Feb. 22, 1973.
Granite City Steel CoGranite City203(d)(6)Apr. 25, 1972.
   (a) Coke oven pushing operationsas amended.
   (b) Charging operationsMay 21, 1973.
Illinois Power Company (Wood River Boiler No. 5)E. Alton204(c)May 1, 1973.
Owens-Illinois IncMadison204(c)May 2, 1973.
Owen-Illinois Inc. (No. 2 Powerhouse)Alton204(c)Mar. 30, 1973.
Shell Oil Co. (Cat. Cracker Units Nos. 1, 2)Roxana203(b)Nov. 27, 1972.
randolf county
Chester Dairy CoChester204(c)Aug. 6, 1973.
st. clair county
Lock Stove CoEast St. Louis205(b)June 11, 1973.
tazewell county
Quaker Oats CoPekin204(c)May 24, 1973.
vermillion county
Lauhoff Grain CoDanville204(c)Mar. 31, 1973.

[38 FR 16145, June 20, 1973, as amended at 38 FR 22742, Aug. 23, 1973; 38 FR 24342, Sept. 7, 1973; 39 FR 28155, Aug. 5, 1974; 51 FR 40675, 40676, 40677, Nov. 7, 1986; 54 FR 25258, June 14, 1989]

return arrow Back to Top

§52.731   Interstate pollutant transport provisions; What are the FIP requirements for decreases in emissions of nitrogen oxides?

(a)(1) The owner and operator of each source and each unit located in the State of Illinois and for which requirements are set forth under the CSAPR NOX Annual Trading Program in subpart AAAAA of part 97 of this chapter must comply with such requirements. The obligation to comply with such requirements will be eliminated by the promulgation of an approval by the Administrator of a revision to Illinois' State Implementation Plan (SIP) as correcting the SIP's deficiency that is the basis for the CSAPR Federal Implementation Plan under §52.38(a), except to the extent the Administrator's approval is partial or conditional.

(2) Notwithstanding the provisions of paragraph (a)(1) of this section, if, at the time of the approval of Illinois' SIP revision described in paragraph (a)(1) of this section, the Administrator has already started recording any allocations of CSAPR NOX Annual allowances under subpart AAAAA of part 97 of this chapter to units in the State for a control period in any year, the provisions of subpart AAAAA of part 97 of this chapter authorizing the Administrator to complete the allocation and recordation of CSAPR NOX Annual allowances to units in the State for each such control period shall continue to apply, unless provided otherwise by such approval of the State's SIP revision.

(b)(1) The owner and operator of each source and each unit located in the State of Illinois and for which requirements are set forth under the CSAPR NOX Ozone Season Group 1 Trading Program in subpart BBBBB of part 97 of this chapter must comply with such requirements with regard to emissions occurring in 2015 and 2016.

(2) The owner and operator of each source and each unit located in the State of Illinois and for which requirements are set forth under the CSAPR NOX Ozone Season Group 2 Trading Program in subpart EEEEE of part 97 of this chapter must comply with such requirements with regard to emissions occurring in 2017 and each subsequent year. The obligation to comply with such requirements will be eliminated by the promulgation of an approval by the Administrator of a revision to Illinois' State Implementation Plan (SIP) as correcting the SIP's deficiency that is the basis for the CSAPR Federal Implementation Plan (FIP) under §52.38(b), except to the extent the Administrator's approval is partial or conditional.

(3) Notwithstanding the provisions of paragraph (b)(2) of this section, if, at the time of the approval of Illinois' SIP revision described in paragraph (b)(2) of this section, the Administrator has already started recording any allocations of CSAPR NOX Ozone Season Group 2 allowances under subpart EEEEE of part 97 of this chapter to units in the State for a control period in any year, the provisions of subpart EEEEE of part 97 of this chapter authorizing the Administrator to complete the allocation and recordation of CSAPR NOX Ozone Season Group 2 allowances to units in the State for each such control period shall continue to apply, unless provided otherwise by such approval of the State's SIP revision.

[77 FR 75384, Dec. 20, 2012, as amended at 81 FR 74586 and 74594, Oct. 26, 2016; 83 FR 65924, Dec. 21, 2018]

return arrow Back to Top

§52.732   Interstate pollutant transport provisions; What are the FIP requirements for decreases in emissions of sulfur dioxide?

(a) The owner and operator of each source and each unit located in the State of Illinois and for which requirements are set forth under the CSAPR SO2 Group 1 Trading Program in subpart CCCCC of part 97 of this chapter must comply with such requirements. The obligation to comply with such requirements will be eliminated by the promulgation of an approval by the Administrator of a revision to Illinois' State Implementation Plan (SIP) as correcting the SIP's deficiency that is the basis for the CSAPR Federal Implementation Plan under §52.39, except to the extent the Administrator's approval is partial or conditional.

(b) Notwithstanding the provisions of paragraph (a) of this section, if, at the time of the approval of Illinois' SIP revision described in paragraph (a) of this section, the Administrator has already started recording any allocations of CSAPR SO2 Group 1 allowances under subpart CCCCC of part 97 of this chapter to units in the State for a control period in any year, the provisions of subpart CCCCC of part 97 of this chapter authorizing the Administrator to complete the allocation and recordation of CSAPR SO2 Group 1 allowances to units in the State for each such control period shall continue to apply, unless provided otherwise by such approval of the State's SIP revision.

[76 FR 48364, Aug. 8, 2011. Redesignated at 77 FR 10334, Feb. 21, 2012, as amended at 81 FR 74586, Oct. 26, 2016]

return arrow Back to Top

§§52.733-52.735   [Reserved]

§52.736   Review of new sources and modifications.

(a) [Reserved]

(b) The rules submitted by the State on March 24, 1988, to satisfy the requirements of the Clean Air Act are approved. These rules are part 203: Major Stationary Sources Construction and Modification as effective March 22, 1991. The moratorium on construction and modification of new sources in nonattainment areas as provided in section 110(a)(2)(I) of the Clean Air Act is revoked.

[57 FR 59935, Dec. 17, 1992]

return arrow Back to Top

§52.737   Operating permits.

Emission limitation and other provisions contained in operating permits issued by the State in accordance with the provisions of the federally approved permit program shall be the applicable requirements of the federally approved Illinois SIP for the purpose of section 113 of the Clean Air Act and shall be enforceable by USEPA and by any person in the same manner as other requirements of the SIP. USEPA reserves the right to deem an operating permit not federally enforceable. Such a determination will be made according to appropriate procedures, and be based upon the permit, permit approval procedures or permit requirements which do not conform with the operating permit program requirements or the requirements of USEPA's underlying regulations.

[57 FR 59936, Dec. 17, 1992]

return arrow Back to Top

§52.738   Significant deterioration of air quality.

(a) The requirements of sections 160 through 165 of the Clean Air Act are not met, since the plan does not include approvable procedures for preventing the significant deterioration of air quality.

(b) Regulations for preventing significant deterioration of air quality. The provisions of §52.21 except paragraph (a)(1) are hereby incorporated and made a part of the applicable State plan for the State of Illinois.

(c) All applications and other information required pursuant to §52.21 from sources located in the State of Illinois shall be submitted to the state agency, Illinois Environmental Protection Agency, 1021 North Grand Avenue East, Springfield, Illinois 62794.

[45 FR 52741, Aug. 7, 1980, as amended at 46 FR 9584, Jan. 29, 1981; 68 FR 11323, Mar. 10, 2003; 68 FR 74489, Dec. 24, 2003; 75 FR 55275, Sept. 10, 2010]

return arrow Back to Top

§52.739   Permit fees.

(a) The requirements of section 110(a)(2)(K) of the Clean Air Act as amended in 1977 are not met since the state has not submitted to EPA, as a part of its State Implementation Plan, provisions for a permit fee system.

[46 FR 23237, Apr. 24, 1981]

return arrow Back to Top

§52.740   Interstate pollution.

(a) The requirements of section 126(a)(2) of the Clean Air Act as amended in 1977 are not met since the state has not submitted to EPA, as a part of its State Implementation Plan, the procedures on which the state is relying to notify nearby states of any proposed major stationary source which may significantly contribute to levels of air pollution in excess of the National Ambient Air Quality Standards in that state.

[46 FR 23237, Apr. 24, 1981]

return arrow Back to Top

§52.741   Control strategy: Ozone control measures for Cook, DuPage, Kane, Lake, McHenry and Will Counties.

(a) General Provisions—(1) Abbreviations and conversion factors. (i) The following abbreviations are used in §52.741:

ASTM   American Society for Testing and Materials

bbl   barrels (42 gallons)

°C   degrees Celsius or centigrade

cm   centimeters

cu in.   cubic inches

°F   degrees Fahrenheit

FIP   Federal implementation plan

ft   feet

ft2   square feet

g   grams

gpm   gallons per minute

g/mole   grams per mole

gal   gallons

hr   hours

in   inches

K   degrees Kelvin

kcal   kilocalories

kg   kilograms

kg/hr   kilograms per hour

kPa   kilopascals; one thousand newtons per square meter

l   liters

l/sec   liters per second

lbs   pounds

lbs/hr   pounds per hour

lbs/gal   pounds per gallon

LEL   lower explosive limit

m   meters

m2   square meters

m3   cubmic meters

mg   milligrams

Mg   Megagrams, metric tons or tonnes

ml   milliliters

min   minutes

MJ   megajoules

mm Hg   millimeters of mercury

ppm   parts per million

ppmv   parts per million by volume

psi   pounds per square inch

psia   pounds per square inch absolute

psig   pounds per square inch gauge

scf   standard cubic feet

scm   standard cubic meters

sec   seconds

SIP   State implementation plan

sq cm   square centimeters

sq in   square inches

USEPA   United States Environmental Protection Agency

VOC   volatile organic compounds

VOL   volatile organic liquids

VOM   volatile organic materials

(ii) The following conversion factors are used in §52.741.

English Metric
1 gal3.785 l.
1,000 gal3,785 l or 3.785 m3.
1 psia6.897 kPa (51.71 mm Hg).
2.205 lbs1 kg.
1 bbl159.0 l.
1 cu in16.39 ml.
1 lb/gal119,800 mg/l.
1 ton0.907 Mg.

(2) Applicability. (i) Any source that received a stay, as indicated in §218.103(a)(2), remains subject to the stay if still in effect, or (if the stay is no longer in effect) the federally-promulgated or federally-approved rule applicable to such source.

(ii)(A) Effective November 20, 1996 Illinois Administrative Code Title 35: Environmental Protection, Subtitle B: Air pollution, Chapter I: Pollution Control Board, Subchapter c: Emissions Standards and Limitations for Stationary Sources, Part 211: Definitions and General Provisions, and Part 218: Organic Material Emission Standards and Limitations for the Chicago Area replace the requirements of 40 CFR 52.741 Control strategy: Ozone control measures for Cook, DuPage, Kane, Lake, McHenry and Will County as the federally enforceable control measures in these counties for the major non-Control Technique Guideline (CTG) sources in the Chicago area, previously subject to paragraph u, v, w, or x because of the applicability criteria in these paragraphs.

(B) In accordance with §218.101(b), for the major non-CTG sources subject to paragraphs u, v, w, or x because of the applicability criteria of those paragraphs, the requirements of paragraphs u, v, w, and x, and the recordkeeping requirements in paragraph y and any related parts of §52.741 necessary to implement these paragraphs (including, but not limited to, those paragraphs containing test methods and definitions), shall remain in effect and are enforceable after November 20, 1996 for the period from July 30, 1990 until November 20, 1996.

(iii)(A) Except as provided in paragraphs (a)(2) (i) and (ii) of this section, effective October 11, 1994, Illinois Administrative Code Title 35: Environmental Protection, Subtitle B: Air pollution, Chapter I: Pollution Control Board, Subchapter c: Emissions Standards and Limitations for Stationary Sources, Part 211: Definitions and General Provisions, and Part 218: Organic Material Emission Standards and Limitations for the Chicago Area replace the requirements of this §52.741 Control strategy: Ozone control measures for Cook, DuPage, Kane, Lake, McHenry and Will County as the federally enforceable control measures in these counties.

(B) In accordance with §218.101(b), the requirements of §52.741 shall remain in effect and are enforceable after October 11, 1994, for the period from July 30, 1990, to October 11, 1994.

(3) Definitions. The following terms are defined for the purpose of §52.741.

Note: The Federal definitions supersede the State definitions for these terms, which were previously approved by USEPA as part of the SIP. The federally approved definitions for all other terms remain in effect and applicable to these Federal rules.

Accelacota means a pharmaceutical coating operation which consists of a horizontally rotating perforated drum in which tablets are placed, a coating is applied by spraying, and the coating is dried by the flow of air across the drum through the perforations.

Accumulator means the reservoir of a condensing unit receiving the condensate from a surface condenser.

Actual emissions means the actual quantity of VOM emissions from an emission source during a particular time period.

Adhesive means any substance or mixture of substances intended to serve as a joining compound.

Administrator means the Administrator of the USEPA or that person's designee.

Afterburner means a control device in which materials in gaseous effluent are combusted.

Air contaminant means any solid, liquid, or gaseous matter, any odor, or any form of energy, that is capable of being released into the atmosphere from an emission source.

Air dried coatings means any coatings that dry by use of air or forced air at temperatures up to 363.15 K (194 °F).

Air pollution means the presence in the atmosphere of one or more air contaminants in sufficient quantities and of such characteristics and duration as to be injurious to human, plant, or animal life, to health, or to property, or to unreasonably interfere with the enjoyment of life or property.

Air pollution control equipment means any equipment or facility of a type intended to eliminate, prevent, reduce or control the emission of specified air contaminants to the atmosphere.

Air suspension coater/dryer means a pharmaceutical coating operation which consists of vertical chambers in which tablets or particles are placed, and a coating is applied and then dried while the tablets or particles are kept in a fluidized state by the passage of air upward through the chambers.

Air-assisted airless spray means a spray coating method which combines compressed air with hydraulic pressure to atomize the coating material into finer droplets than is achieved with pure airless spray. Lower hydraulic pressure is used than with airless spray.

Airless spray means a spray coating method in which the coating is atomized by forcing it through a small opening at high pressure. The coating liquid is not mixed with air before exiting from the nozzle.

Allowable emissions means the quantity of VOM emissions during a particular time period from a stationary source calculated using the maximum rated capacity of the source (unless restricted by federally enforceable limitations on operating rate, hours of operation, or both) and the most stringent of:

(A) The applicable standards in 40 CFR parts 60 and 61:

(B) The applicable implementation plan; or

(C) A federally enforceable permit.

Ambient air quality standards means those standards designed to protect the public health and welfare codified in 40 CFR part 50 and promulgated from time to time by the USEPA pursuant to authority contained in Section 108 of the Clean Air Act, 42 U.S.C. 7401 et seq., as amended from time to time.

Applicator means a device used in a coating line to apply coating.

As applied means the exact formulation of a coating during application on or impregnation into a substrate.

Asphalt means the dark-brown to black cementitious material (solid, semisolid, or liquid in consistency) of which the main constituents are bitumens which occur naturally or as a residue of petroleum refining.

Automobile means a motor vehicle capable of carrying no more than 12 passengers.

Automobile or light-duty truck assembly plant means a facility where parts are assembled or finished for eventual inclusion into a finished automobile or light-duty truck ready for sale to vehicle dealers, but not including customizers, body shops, and other repainters.

Automobile or light-duty truck refinishing means the repainting of used automobiles and light-duty trucks.

Baked coatings means any coating which is cured or dried in an oven where the oven air temperature exceeds 90 °C (194 °F).

Binders means organic materials and resins which do not contain VOM's.

Bituminous coatings means black or brownish coating materials which are soluble in carbon disulfide, which consist mainly of hydrocarbons, and which are obtained from natural deposits or as residues from the distillation of crude oils or of low grades of coal.

Brush or wipe coating means a manual method of applying a coating using a brush, cloth, or similar object.

Bulk gasoline plant means a gasoline storage and distribution facility with an average throughput of 76,000 l (20,000 gal) or less on a 30-day rolling average that distributes gasoline to gasoline dispensing facilities.

Can means any metal container, with or without a top, cover, spout or handles, into which solid or liquid materials are packaged.

Can coating means any coating applied on a single walled container that is manufactured from metal sheets thinner than 29 gauge (0.0141 in.).

Can coating facility means a facility that includes one or more can coating line(s).

Can coating line means a coating line in which any protective, decorative, or functional coating is applied onto the surface of cans or can components.

Capture means the containment or recovery of emissions from a process for direction into a duct which may be exhausted through a stack or sent to a control device. The overall abatement of emissions from a process with an add-on control device is a function both of the capture efficiency and of the control device.

Capture device means a hood, enclosed room floor sweep or other means of collecting solvent or other pollutants into a duct. The pollutant can then be directed to a pollution control device such as an afterburner or carbon adsorber. Sometimes the term is used loosely to include the control device.

Capture efficiency means the fraction of all VOM generated by a process that are directed to an abatement or recovery device.

Capture system means all equipment (including, but not limited to, hoods, ducts, fans, ovens, dryers, etc.) used to contain, collect and transport an air pollutant to a control device.

Clean Air Act means the Clean Air Act of 1963, as amended, including the Clean Air Act Amendments of 1977, (42 U.S.C. 7401 et seq.).

Clear coating means coatings that lack color and opacity or are transparent using the undercoat as a reflectant base or undertone color.

Clear topcoat means the final coating which contains binders, but not opaque pigments, and is specifically formulated to form a transparent or translucent solid protective film.

Closed vent system means a system that is not open to the atmosphere and is composed of piping, connections, and, if necessary, flow inducing devices that transport gas or vapor from an emission source to a control device.

Coating means a material applied onto or impregnated into a substrate for protective, decorative, or functional purposes. Such materials include, but are not limited to, paints, varnishes, sealers, adhesives, thinners, diluents, and inks.

Coating applicator means equipment used to apply a coating.

Coating line means an operation consisting of a series of one or more coating applicators and any associated flash-off areas, drying areas, and ovens wherein a surface coating is applied, dried, or cured. (It is not necessary for an operation to have an oven, or flash-off area, or drying area to be included in this definition.)

Coating plant means any plant that contains one or more coating line(s).

Coil means any flat metal sheet or strip that is rolled or wound in concentric rings.

Coil coating means any coating applied on any flat metal sheet or strip that comes in rolls or coils.

Coil coating facility means a facility that includes one or more coil coating line(s).

Coil coating line means a coating line in which any protective, decorative or functional coating is applied onto the surface of flat metal sheets, strips, rolls, or coils for industrial or commercial use.

Cold cleaning means the process of cleaning and removing soils from surfaces by spraying, brushing, flushing, or immersion while maintaining the organic solvent below its boiling point. Wipe cleaning is not included in this definition.

Component means, with respect to synthetic organic chemical and polymer manufacturing equipment, and petroleum refining and related industries, any piece of equipment which has the potential to leak VOM including, but not limited to, pump seals, compressor seals, seal oil degassing vents, pipeline valves, pressure relief devices, process drains, and open ended pipes. This definition excludes valves which are not externally regulated, flanges, and equipment in heavy liquid service. For purposes of paragraph (i) of this section, this definition also excludes bleed ports of gear pumps in polymer service.

Concrete curing compounds means any coating applied to freshly poured concrete to retard the evaporation of water.

Condensate means volatile organic liquid separated from its associated gases, which condenses due to changes in the temperature or pressure and remains liquid at standard conditions.

Continuous process means, with respect to polystyrene resin, a method of manufacture in which the styrene raw material is delivered on a continuous basis to the reactor in which the styrene is polymerized to polystyrene.

Control device means equipment (such as an afterburner or adsorber) used to remove or prevent the emission of air pollutants from a contaminated exhaust stream.

Control device efficiency means the ratio of pollution prevented by a control device and the pollution introduced to the control device, expressed as a percentage.

Conveyorized degreasing means the continuous process of cleaning and removing soils from surfaces utilizing either cold or vaporized solvents.

Crude oil means a naturally occurring mixture which consists of hydrocarbons and sulfur, nitrogen, or oxygen derivatives of hydrocarbons and which is a liquid at standard conditions.

Crude oil gathering means the transportation of crude oil or condensate after custody transfer between a production facility and a reception point.

Custody transfer means the transfer of produced petroleum and/or condensate after processing and/or treating in the producing operations, from storage tanks or automatic transfer facilities to pipelines or any other forms of transportation.

Daily-weighted average VOM content means the average VOM content of two or more coatings as applied on a coating line during any day, taking into account the fraction of total coating volume that each coating represents, as calculated with the following equation:

eCFR graphic ec07no91.000.gif

View or download PDF

Where:

VOMw = The average VOM content of two or more coatings as applied each day on a coating line in units of kg VOM/l (lbs VOM/gal) of coating (minus water and any compounds which are specifically exempted from the definition of VOM),

n = The number of different coatings as applied each day on a coating line,

Vi = The volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each day on a coating line in units of l (gal).

Ci = The VOM content of each coating as applied each day on a coating line in units of kg VOM/l (lbs VOM/gal) of coating (minus water and any compounds which are specifically exempted from the definition of VOM), and

VT = The total volume of all coatings (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each day on a coating line in units of l (gal).

Day means the consecutive 24 hours beginning at 12 a.m. (midnight) local time.

Degreaser means any equipment or system used in solvent cleaning.

Delivery vessel means any tank truck or trailer equipped with a storage tank that is used for the transport of gasoline to a stationary storage tank at a gasoline dispensing facility, bulk gasoline plant, or bulk gasoline terminal.

Dip coating means a method of applying coatings in which the part is submerged in a tank filled with the coating.

Drum means any cylindrical metal shipping container of 13- to 110-gallon capacity.

Electrostatic bell or disc spray means an electrostatic spray coating method in which a rapidly-spinning bell- or disc-shaped applicator is used to create a fine mist and apply the coating with high transfer efficiency.

Electrostatic spray means a spray coating method in which opposite electrical charges are applied to the substrate and the coating. The coating is attracted to the object due to the electrostatic potential between them.

Emission source and source mean any facility from which VOM is emitted or capable of being emitted into the atmosphere.

Enamel means a coating that cures by chemical cross-linking of its base resin. Enamels can be distinguished from lacquers because enamels are not readily resoluble in their original solvent.

Enclose means to cover any VOL surface that is exposed to the atmosphere.

End sealing compound coat means a compound applied to can ends which functions as a gasket when the end is assembled onto the can.

Excessive release means a discharge of more than 295 g (0.65 lbs) of mercaptans and/or hydrogen sulfide into the atmosphere in any 5-minute period.

Exterior base coat means a coating applied to the exterior of a can body, or flat sheet to provide protection to the metal or to provide background for any lithographic or printing operation.

Exterior end coat means a coating applied to the exterior end of a can to provide protection to the metal.

External-floating roof means a cover over an open top storage tank consisting of a double deck or pontoon single deck which rests upon and is supported by the volatile organic liquid being contained and is equipped with a closure seal or seals to close the space between the roof edge and tank shell.

Extreme environmental conditions means exposure to any or all of the following: ambient weather conditions; temperatures consistently above 95 °C (203 °F); detergents; abrasive and scouring agents; solvents; or corrosive atmospheres.

Extreme performance coating means any coating which during intended use is exposed to extreme environmental conditions.

Fabric coating means any coating applied on textile fabric. Fabric coating includes the application of coatings by impregnation.

Fabric coating facility means a facility that includes one or more fabric coating lines.

Fabric coating line means a coating line in which any protective, decorative, or functional coating or reinforcing material is applied on or impregnated into a textile fabric.

Federally enforceable means all limitations and conditions which are enforceable by the Administrator including those requirements developed pursuant to 40 CFR parts 60 and 61; requirements within any applicable implementation plan; and any permit requirements established pursuant to 40 CFR 52.21 or under regulations approved pursuant to 40 CFR part 51 subpart I and 40 CFR 51.166.

Final repair coat means the repainting of any topcoat which is damaged during vehicle assembly.

Firebox means the chamber or compartment of a boiler or furnace in which materials are burned, but not the combustion chamber or afterburner of an incinerator.

Fixed-roof tank means a cylindrical shell with a permanently affixed roof.

Flexographic printing means the application of words, designs, and pictures to a substrate by means of a roll printing technique in which the pattern to be applied is raised above the printing roll and the image carrier is made of elastomeric materials.

Flexographic printing line means a printing line in which each roll printer uses a roll with raised areas for applying an image such as words, designs, or pictures to a substrate. The image carrier on the roll is made of rubber or other elastome

Floating roof means a roof on a stationary tank, reservoir, or other container which moves vertically upon change in volume of the stored material.

Fountain solution means the solution which is applied to the image plate to maintain hydrophilic properties of the non-image areas.

Fuel combustion emission source means any furnace, boiler, or similar equipment used for the primary purpose of producing heat or power by indirect heat transfer.

Fuel gas system means a system for collection of refinery fuel gas including, but not limited to, piping for collecting tail gas from various process units, mixing drums and controls, and distribution piping.

Gas/gas method means either of two methods for determining capture which rely only on gas phase measurements. The first method requires construction of a temporary total enclosure (TTE) to ensure that all would-be fugitive emissions are measured. The second method uses the building or room which houses the facility as an enclosure. The second method requires that all other VOM sources within the room be shut down while the test is performed, but all fans and blowers within the room must be operated according to normal procedures.

Gas service means that the component contains process fluid that is in the gaseous state at operating conditions.

Gasoline means any petroleum distillate or petroleum distillate/alcohol blend having a Reid vapor pressure of 27.6 kPa or greater which is used as a fuel for internal combustion engines.

Gasoline dispensing facility means any site where gasoline is transferred from a stationary storage tank to a motor vehicle gasoline tank used to provide fuel to the engine of that motor vehicle.

Gross vehicle weight means the manufacturer's gross weight rating for the individual vehicle.

Gross vehicle weight rating means the value specified by the manufacturer as the maximum design loaded weight of a single vehicle.

Heated airless spray means an airless spray coating method in which the coating is heated just prior to application.

Heatset means a class of web-offset lithography which requires a heated dryer to solidify the printing inks.

Heatset-web-offset lithographic printing line means a lithographic printing line in which a blanket cylinder is used to transfer ink from a plate cylinder to a substrate continuously fed from a roll or an extension process and an oven is used to solidify the printing inks.

Heavy liquid means liquid with a true vapor pressure of less than 0.3 kPa (0.04 psi) at 294.3 K (70 °F) established in a standard reference text or as determined by ASTM method D2879-86 (incorporated by reference as specified in 40 CFR 52.742); or which has 0.1 Reid Vapor Pressure as determined by ASTM method D323-82 (incorporated by reference as specified in 40 CFR 52.742); or which when distilled requires a temperature of 421.95 K (300 °F) or greater to recover 10 percent of the liquid as determined by ASTM method D86-82 (incorporated by reference as specified in 40 CFR 52.742).

Heavy off-highway vehicle products means, for the purpose of paragraph (e) of this section, heavy construction, mining, farming, or material handling equipment; heavy industrial engines; diesel-electric locomotives and associated power generation equipment; and the components of such equipment or engines.

Heavy off-highway vehicle products coating facility means a facility that includes one or more heavy off-highway vehicle products coating line(s).

Heavy off-highway vehicle products coating line means a coating line in which any protective, decorative, or functional coating is applied onto the surface of heavy off-highway vehicle products.

High temperature aluminum coating means a coating that is certified to withstand a temperature of 537.8 °C (1000 °F) for 24 hours.

Hood means a partial enclosure or canopy for capturing and exhausting, by means of a draft, the organic vapors or other fumes rising from a coating process or other source.

Hood capture efficiency means the emissions from a process which are captured by the hood and directed into a control device, expressed as a percentage of all emissions.

Hot well means the reservoir of a condensing unit receiving the condensate from a barometric condenser.

Hour means a block period of 60 minutes (e.g., 1 a.m. to 2 a.m.).

In vacuum service means, for the purpose of paragraph (i) of this section, equipment which is operating at an internal pressure that is at least 5 kPa (0.73 psia) below ambient pressure.

In-process tank means a container used for mixing, blending, heating, reacting, holding, crystallizing, evaporating or cleaning operations in the manufacture of pharmaceuticals.

Incinerator means a combustion apparatus in which refuse is burned.

Indirect heat transfer means transfer of heat in such a way that the source of heat does not come into direct contact with process materials.

Ink means a coating used in printing, impressing, or transferring an image onto a substrate.

Interior body spray coat means a coating applied by spray to the interior of a can body.

Internal-floating roof means a cover or roof in a fixed-roof tank which rests upon and is supported by the volatile organic liquid being contained and is equipped with a closure seal or seals to close the space between the roof edge and tank shell.

Lacquers means any clear wood finishes formulated with nitrocellulose or synthetic resins to dry by evaporation without chemical reaction, including clear lacquer sanding sealers.

Large appliance means any residential and commercial washers, dryers, ranges, refrigerators, freezers, water heaters, dish washers, trash compactors, air conditioners, and other similar products.

Large appliance coating means any coating applied to the component metal parts (including, but not limited to, doors, cases, lids, panels, and interior support parts) of residential and commercial washers, dryers, ranges, refrigerators, freezers, water heaters, dish washers, trash compactors, air conditioners, and other similar products.

Large appliance coating facility means a facility that includes one or more large appliance coating line(s).

Large appliance coating line means a coating line in which any protective, decorative, or functional coating is applied onto the surface of large appliances.

Light liquid means VOM in the liquid state which is not defined as heavy liquid.

Light-duty truck means any motor vehicle rated at 3,850 kg gross vehicle weight or less, designed mainly to transport property.

Liquid/gas method means either of two methods for determining capture which require both gas phase and liquid phase measurements and analysis. The first method requires construction of a TTE. The second method uses the building or room which houses the facility as an enclosure. The second method requires that all other VOM sources within the room be shut down while the test is performed, but all fans and blowers within the room must be operated according to normal procedures.

Liquid service means that the equipment or component contains process fluid that is in a liquid state at operating conditions.

Lithographic printing line means a printing line, except that the substrate is not necessarily fed from an unwinding roll, in which each roll printer uses a roll where both the image and non-image areas are essentially in the same plane (planographic).

Magnet wire means aluminum or copper wire formed into an electromagnetic coil.

Magnet wire coating means any coating or electrically insulating varnish or enamel applied to magnet wire.

Magnet wire coating facility means a facility that includes one or more magnet wire coating line(s).

Magnet wire coating line means a coating line in which any protective, decorative, or functional coating is applied onto the surface of a magnet wire.

Malfunction means any sudden and unavoidable failure of air pollution control equipment, process equipment, or a process to operate in a normal or usual manner. Failures that are caused entirely or in part by poor maintenance, careless operation, or any other preventable upset condition or preventable equipment breakdown shall not be considered malfunctions.

Manufacturing process means a method whereby a process emission source or series of process emission sources is used to convert raw materials, feed stocks, subassemblies, or other components into a product, either for sale or for use as a component in a subsequent manufacturing process.

Maximum theoretical emissions means the quantity of volatile organic material emissions that theoretically could be emitted by a stationary source before add-on controls based on the design capacity or maximum production capacity of the source and 8760 hours per year. The design capacity or maximum production capacity includes use of coating(s) or ink(s) with the highest volatile organic material content actually used in practice by the source.

Metal furniture means a furniture piece including, but not limited to, tables, chairs, waste baskets, beds, desks, lockers, benches, shelving, file cabinets, lamps, and room dividers.

Metal furniture coating means any non-adhesive coating applied to any furniture piece made of metal or any metal part which is or will be assembled with other metal, wood, fabric, plastic or glass parts to form a furniture piece including, but not limited to, tables, chairs, waste baskets, beds, desks, lockers, benches, shelving, file cabinets, lamps, and room dividers. This definition shall not apply to any coating line coating miscellaneous metal parts or products.

Metal furniture coating facility means a facility that includes one or more metal furniture coating line(s).

Metal furniture coating line means a coating line in which any protective, decorative, or functional coating is applied onto the surface of metal furniture.

Metallic shoe-type seal means a primary or secondary seal constructed of metal sheets (shoes) which are joined together to form a ring, springs, or levers which attach the shoes to the floating roof and hold the shoes against the tank wall, and a coated fabric which is suspended from the shoes to the floating roof.

Miscellaneous fabricated product manufacturing process means:

(A) A manufacturing process involving one or more of the following applications, including any drying and curing of formulations, and capable of emitting VOM:

(1) Adhesives to fabricate or assemble components or products.

(2) Asphalt solutions to paper or fiberboard.

(3) Asphalt to paper or felt.

(4) Coatings or dye to leather.

(5) Coatings to plastic.

(6) Coatings to rubber or glass.

(7) Disinfectant material to manufactured items.

(8) Plastic foam scrap or “fluff” from the manufacture of foam containers and packaging material to form resin pallets.

(9) Resin solutions to fiber substances.

(10) Viscose solutions for food casings.

(B) The storage and handling of formulations associated with the process described above, and the use and handling of organic liquids and other substances for clean-up operations associated with the process described in this definition.

Miscellaneous formulation manufacturing process means:

(A) A manufacturing process which compounds one or more of the following and is capable of emitting VOM:

(1) Adhesives.

(2) Asphalt solutions.

(3) Caulks, sealants, or waterproofing agents.

(4) Coatings, other than paint and ink.

(5) Concrete curing compounds.

(6) Dyes.

(7) Friction materials and compounds.

(8) Resin solutions.

(9) Rubber solutions.

(10) Viscose solutions.

(B) The storage and handling of formulations associated with the process described above, and the use and handling of organic liquids and other substances for clean-up operations associated with the process described in this definition.

Miscellaneous metal parts or products means any metal part or metal product, even if attached to or combined with a nonmental part or product, except cans, coils, metal furniture, large appliances, magnet wire, automobiles, ships, and airplane bodies.

Miscellaneous metal parts and products coating means any coating applied to any metal part or metal product, even if attached to or combined with a nonmetal part or product, except cans, coils, metal furniture, large appliances, and magnet wire. Prime coat, prime surfacer coat, topcoat, and final repair coat for automobiles and light-duty trucks are not miscellaneous metal parts and products coatings. However, underbody anti-chip (e.g., underbody plastisol) automobile, and light-duty truck coatings are miscellaneous metal parts and products coatings. Also, automobile or light-duty truck refinishing coatings, coatings applied to the exterior of marine vessels, coatings applied to the exterior of airplanes, and the customized topcoating of automobiles and trucks if production is less than 35 vehicles per day are not miscellaneous metal parts and products coatings.

Miscellaneous metal parts or products coating facility means a facility that includes one or more miscellaneous metal parts or products coating lines.

Miscellaneous metal parts or products coating line means a coating line in which any protective, decorative, or functional coating is applied onto the surface of miscellaneous metal parts or products.

Miscellaneous organic chemical manufacturing process means:

(A) A manufacturing process which produces by chemical reaction, one or more of the following organic compounds or mixtures of organic compounds and which is capable of emitting VOM:

(1) Chemicals listed in appendix A of this section.

(2) Chlorinated and sulfonated compounds.

(3) Cosmetic, detergent, soap, or surfactant intermediaries or specialties and products.

(4) Disinfectants.

(5) Food additives.

(6) Oil and petroleum product additives.

(7) Plasticizers.

(8) Resins or polymers.

(9) Rubber additives.

(10) Sweeteners.

(11) Varnishes.

(B) The storage and handling of formulations associated with the process described above and the use and handling of organic liquids and other substances for clean-up operations associated with the process described in this definition.

Monitor means to measure and record.

Multiple package coating means a coating made from more than one different ingredient which must be mixed prior to using and has a limited pot life due to the chemical reaction which occurs upon mixing.

Offset means, with respect to printing and publishing operations, use of a blanket cylinder to transfer ink from the plate cylinder to the surface to be printed.

Opaque stains means all stains that are not semi-transparent stains.

Open top vapor depressing means the batch process of cleaning and removing soils from surfaces by condensing hot solvent vapor on the colder metal parts.

Open-ended valve means any valve, except pressure relief devices, having one side of the valve in contact with process fluid and one side open to the atmosphere, either directly or through open piping.

Organic compound means any compound of carbon, excluding carbon monoxide, carbon dioxide, carbonic acid, metallic carbides or carbonates, and ammonium carbonate.

Organic material means any chemical compound of carbon including diluents and thinners which are liquids at standard conditions and which are used as dissolvers, viscosity reducers, or cleaning agents, but excluding methane, carbon monoxide, carbon dioxide, carbonic acid, metallic carbonic acid, metallic carbide, metallic carbonates, and ammonium carbonate.

Organic vapor means the gaseous phase of an organic material or a mixture of organic materials present in the atmosphere.

Oven means a chamber within which heat is used for one or more of the following purposes: Dry, bake, cure, or polymerize a coating or ink.

Overall control means the product of the capture efficiency and the control device efficiency.

Overvarnish means a transparent coating applied directly over ink or coating.

Owner or operator means any person who owns, operates, leases, controls, or supervises an emission source or air pollution control equipment.

Packaging rotogravure printing means rotogravure printing upon paper, paper board, metal foil, plastic film, and other substrates, which are, in subsequent operations, formed into packaging products or labels for articles to be sold.

Packaging rotogravure printing line means a rotogravure printing line in which surface coatings are applied to paper, paperboard, foil, film, or other substrates which are to be used to produce containers, packaging products, or labels for articles.

Pail means any cylindrical metal shipping container of 1- to 12-gallon capacity and constructed of 29-gauge and heavier metal.

Paint manufacturing plant means a plant that mixes, blends, or compounds enamels, lacquers, sealers, shellacs, stains, varnishes, or pigmented surface coatings.

Paper coating means any coating applied on paper, plastic film, or metallic foil to make certain products, including (but not limited to) adhesive tapes and labels, book covers, post cards, office copier paper, drafting paper, or pressure sensitive tapes. Paper coating includes the application of coatings by impregnation and/or saturation.

Paper coating facility means a facility that includes one or more paper coating lines.

Paper coating line means a coating line in which any protective, decorative, or functional coating is applied on, saturated into, or impregnated into paper, plastic film, or metallic foil to make certain products, including (but not limited to) adhesive tapes and labels, book covers, post cards, office copier paper, drafting paper, and pressure sensitive tapes.

Parts per million (volume) means a volume/volume ratio which expresses the volumetric concentration of gaseous air contaminant in a million unit volume of gas.

Person means any individual, corporation, partnership, association, State, municipality, political subdivision of a State; any agency, department, or instrumentality of the United States; and any officer, agent, or employee thereof.

Petroleum means the crude oil removed from the earth and the oils derived from tar sands, shale, and coal.

Petroleum refinery means any facility engaged in producing gasoline, kerosene, distillate fuel oils, residual fuel oils, lubricants, or other products through distillation of petroleum, or through redistillation, cracking, or reforming of unfinished petroleum derivatives.

Pharmaceutical means any compound or mixture, other than food, used in the prevention, diagnosis, alleviation, treatment, or cure of disease in man and animal.

Pharmaceutical coating operation means a device in which a coating is applied to a pharmaceutical, including air drying or curing of the coating.

Pigmented coatings means opaque coatings containing binders and colored pigments which are formulated to conceal the wood surface either as an undercoat or topcoat.

Plant means all of the pollutant-emitting activities which belong to the same industrial grouping, are located on one or more contiguous or adjacent properties, and are under the control of the same person (or persons under common control), except the activities of any marine vessel. Pollutant-emitting activities shall be considered as part of the same industrial grouping if they belong to the same “Major Group” (i.e., which have the same two-digit code) as described in the “Standard Industrial Classification Manual, 1987” (incorporated by reference as specified in 40 CFR 52.742).

Plasticizers means a substance added to a polymer composition to soften and add flexibility to the product.

Prime coat means the first of two or more coatings applied to a surface.

Prime surfacer coat means a coating used to touch up areas on the surface of automobile or light-duty truck bodies not adequately covered by the prime coat before application of the top coat. The prime surfacer coat is applied between the prime coat and topcoat. An anti-chip coating applied to main body parts (e.g., rocker panels, bottom of doors and fenders, and leading edge of roof) is a prime surfacer coat.

Primers means any coatings formulated and applied to substrates to provide a firm bond between the substrate and subsequent coats.

Printing means the application of words, designs, and pictures to a substrate using ink.

Printing line means an operation consisting of a series of one or more roll printers and any associated roll coaters, drying areas, and ovens wherein one or more coatings are applied, dried, and/or cured.

Process means any stationary emission source other than a fuel combustion emission source or an incinerator.

Production equipment exhaust system means a system for collecting and directing into the atmosphere emissions of volatile organic material from reactors, centrifuges, and other process emission sources.

Publication rotogravure printing line means a rotogravure printing line in which coatings are applied to paper which is subsequently formed into books, magazines, catalogues, brochures, directories, newspaper supplements, or other types of printed material.

Reactor means a vat, vessel, or other device in which chemical reactions take place.

Refiner means any person who owns, leases operates, controls, or supervises a refinery.

Refinery unit, process unit or unit means a set of components which are a part of a basic process operation such as distillation, hydrotreating, cracking, or reforming of hydrocarbons.

Refrigerated condenser means a surface condenser in which the coolant supplied to the condenser has been cooled by a mechanical device, other than by a cooling tower or evaporative spray cooling, such as refrigeration unit or steam chiller unit.

Repair coatings means coatings used to correct imperfections or damage to furniture surface.

Repaired means, for the purpose of paragraph (i) of this section, that equipment component has been adjusted, or otherwise altered, to eliminate a leak.

Roll coater means an apparatus in which a uniform layer of coating is applied by means of one or more rolls across the entire width of a moving substrate.

Roll printer means an apparatus used in the application of words, designs, or pictures to a substrate, usually by means of one or more rolls each with only partial coverage.

Roll printing means the application of words, designs, and pictures to a substrate usually by means of a series of hard rubber or metal rolls each with only partial coverage.

Roller coating means a method of applying a coating to a sheet or strip in which the coating is transferred by a roller or series of rollers.

Rotogravure printing means the application of words, designs, and pictures to a substrate by means of a roll printing technique in which the pattern to be applied is recessed relative to the non-image area.

Rotogravure printing line means a printing line in which each roll printer uses a roll with recessed areas for applying an image to a substrate.

Safety relief valve means a valve which is normally closed and which is designed to open in order to relieve excessive pressures within a vessel or pipe.

Sanding sealers means any coatings formulated for and applied to bare wood for sanding and to seal the wood for subsequent application of varnish. To be considered a sanding sealer a coating must be clearly labelled as such.

Sealer means a coating containing binders which seals wood prior to the application of the subsequent coatings.

Semi-transparent stains means stains containing dyes or semi-transparent pigments which are formulated to enhance wood grain and change the color of the surface but not to conceal the surface, including, but not limited to, sap stain, toner, non-grain raising stains, pad stain, or spatter stain.

Set of safety relief valves means one or more safety relief valves designed to open in order to relieve excessive pressures in the same vessel or pipe.

Sheet basecoat means a coating applied to metal when the metal is in sheet form to serve as either the exterior or interior of a can for either two-piece or three-piece cans.

Side-seam spray coat means a coating applied to the seam of a three-piece can.

Single coat means one coating application applied to a metal surface.

Solvent means a liquid substance that is used to dissolve or dilute another substance.

Solvent cleaning means the process of cleaning soils from surfaces by cold cleaning, open top vapor degreasing, or conveyorized degreasing.

Specified air contaminant means any air contaminant as to which this Section contains emission standards or other specific limitations.

Splash loading means a method of loading a tank, railroad tank car, tank truck, or trailer by use of other than a submerged loading pipe.

Standard conditions means a temperature of 70 °F and a pressure of 14.7 psia.

Standard cubic foot (scf) means the volume of one cubic foot of gas at standard conditions.

Standard Industrial Classification Manual means the Standard Industrial Classification Manual (1987), Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402 (incorporated by reference as specified in 40 CFR 52.742).

Start-up means the setting in operation of an emission source for any purpose.

Stationary emission source and Stationary source mean an emission source which is not self-propelled.

Storage tank or storage vessel means any stationary tank, reservoir or container used for the storage of VOL's.

Submerged loading pipe means any discharge pipe or nozzle which meets either of the following conditions:

(A) Where the tank is filled from the top, the end of the discharge pipe or nozzle must be totally submerged when the liquid level is 15 cm (6 in.) above the bottom of the tank.

(B) Where the tank is filled from the side, the discharge pipe or nozzle must be totally submerged when the liquid level is 46 cm (18 in.) above the bottom of the tank.

Substrate means the surface onto which a coating is applied or into which a coating is impregnated.

Surface condenser means a device which removes a substance from a gas stream by reducing the temperature of the stream, without direct contact between the coolant and the stream.

Tablet coating operation means a pharmaceutical coating operation in which tablets are coated.

Thirty-day rolling average means any value arithmetically averaged over any consecutive thirty-days.

Three-piece can means a can which is made from a rectangular sheet and two circular ends.

Topcoat means a coating applied in a multiple coat operation other than prime coat, final repair coat, or prime surfacer coat.

Topcoat operation means all topcoat spray booths, flash-off areas, and bake ovens at a facility which are used to apply, dry, or cure the final coatings (except final off-line repair) on components of automobile or light-duty truck bodies.

Transfer efficiency means the ratio of the amount of coating solids deposited onto a part or product to the total amount of coating solids used.

True vapor pressure means the equilibrium partial pressure exerted by a volatile organic liquid as determined in accordance with methods described in American Petroleum Institute Bulletin 2517, “Evaporation Loss From Floating Roof Tanks,” second edition, February 1980 (incorporated by reference as specified in 40 CFR 52.742).

Two-piece can means a can which is drawn from a shallow cup and requires only one end to be attached.

Undercoaters means any coatings formulated for and applied to substrates to provide a smooth surface for subsequent coats.

Unregulated safety relief valve means a safety relief valve which cannot be actuated by a means other than high pressure in the pipe or vessel which it protects.

Vacuum producing system means any reciprocating, rotary, or centrifugal blower or compressor or any jet ejector or device that creates suction from a pressure below atmospheric and discharges against a greater pressure.

Valves not externally regulated means valves that have no external controls, such as in-line check valves.

Vapor balance system means any combination of pipes or hoses which creates a closed system between the vapor spaces of an unloading tank and a receiving tank such that vapors displaced from the receiving tank are transferred to the tank being unloaded.

Vapor collection system means all piping, seals, hoses, connections, pressure-vacuum vents, and other possible sources between the gasoline delivery vessel and the vapor processing unit and/or the storage tanks and vapor holder.

Vapor control system means any system that limits or prevents release to the atmosphere of organic material in the vapors displaced from a tank during the transfer of gasoline.

Vapor recovery system means a vapor gathering system capable of collecting all VOM vapors and gases discharged from the storage tank and a vapor disposal system capable of processing such VOM vapors and gases so as to prevent their emission to the atmosphere.

Vehicle means a device by which any person or property may be propelled, moved, or drawn upon a highway, excepting a device moved exclusively by human power or used exclusively upon stationary rails or tracks.

Vinyl coating means any topcoat or printing ink applied to vinyl coated fabric or vinyl sheets. Vinyl coating does not include plastisols.

Vinyl coating facility means a facility that includes one or more vinyl coating line(s).

Vinyl coating line means a coating line in which any protective, decorative or functional coating is applied onto vinyl coated fabric or vinyl sheets.

Volatile organic liquid means any substance which is liquid at storage conditions and which contains volatile organic compounds.

Volatile organic material (VOM) or volatile organic compounds (VOC) is as defined in §51.100(s) of this chapter.

Wash coat means a coating containing binders which seals wood surfaces, prevents undesired staining, and controls penetration.

Web means a substrate which is printed in continuous roll-fed presses.

Wood furniture means room furnishings including cabinets (kitchen, bath, and vanity), tables, chairs, beds, sofas, shutters, art objects, wood paneling, wood flooring, and any other coated furnishings made of wood, wood composition, or fabricated wood materials.

Wood furniture coating facility means a facility that includes one or more wood furniture coating line(s).

Wood furniture coating line means a coating line in which any protective, decorative, or functional coating is applied onto wood furniture.

Woodworking means the shaping, sawing, grinding, smoothing, polishing, and making into products of any form or shape of wood.

(4) Testing methods and procedures—(i) Coatings, inks and fountain solutions. The following test methods and procedures shall be used to determine compliance of as applied coatings, inks, and fountain solutions with the limitations set forth in §52.741.

(A) Sampling. Samples collected for analyses shall be one-liter taken into a one-liter container at a location and time such that the sample will be representative of the coating as applied (i.e., the sample shall include any dilution solvent or other VOM added during the manufacturing process). The container must be tightly sealed immediately after the sample is taken. Any solvent or other VOM added after the sample is taken must be measured and accounted for in the calculations in paragraph (a)(4)(i)(C) of this section. For multiple package coatings, separate samples of each component shall be obtained. A mixed sample shall not be obtained as it will cure in the container. Sampling procedures shall follow the guidelines presented in:

(1) ASTM D3925-81 (Reapproved 1985) Standard Practice for Sampling Liquid Paints and Related Pigment Coating. This practice is incorporated by reference as specified in 40 CFR 52.742.

(2) ASTM E300-86 Standard Practice for Sampling Industrial Chemicals. This practice is incorporated by reference as specified in 40 CFR 52.742.

(B) Analyses. The applicable analytical methods specified below shall be used to determine the composition of coatings, inks, or fountain solutions as applied.

(1) Method 24 of 40 CFR part 60, appendix A, shall be used to determine the VOM content and density of coatings. If it is demonstrated to the satisfaction of the Administrator that plant coating formulation data are equivalent to Method 24 results, formulation data may be used. In the event of any inconsistency between a Method 24 test and a facility's formulation data, the Method 24 test will govern.

(2) Method 24A of 40 CFR part 60, appendix A, shall be used to determine the VOM content and density of rotogravure printing inks and related coatings. If it is demonstrated to the satisfaction of the Administrator that the plant coating formulation data are equivalent to Method 24A results, formulation data may be used. In the event of any inconsistency between a Method 24A test and a facility's formulation data, the Method 24A test will govern.

(3) The following ASTM methods are the analytical procedures for determining VOM:

(i) ASTM D1475-85: Standard Test Method for Density of Paint, Varnish, Lacquer and Related Products. This test method is incorporated by reference as specified in 40 CFR 52.742.

(ii) ASTM D2369-87: Standard Test Method for Volatile Content of Coatings. This test method is incorporated by reference as specified in 40 CFR 52.742.

(iii) ASTM D3792-86: Standard Test Method for Water Content of Water-reducible Paints by Direct Injection into a Gas Chromatograph. This test method is incorporated by reference as specified in 40 CFR 52.742.

(iv) ASTM D4017-81 (Reapproved 1987): Standard Test Method for Water in Paints and Paint Materials by the Karl Fischer Method. This test method is incorporated by reference as specified in 40 CFR 52.742.

(v) ASTM D4457-85: Standard Test Method for Determination of Dichloromethane and 1,1,1-Trichloroethane in Paints and Coatings by Direct Injection into a Gas Chromatograph. (The procedure delineated above can be used to develop protocols for any compounds specifically exempted from the definition of VOM.) This test method is incorporated by reference as specified in 40 CFR 52.742.

(vi) ASTM D2697-86: Standard Test Method for Volume Non-Volatile Matter in Clear or Pigmented Coatings. This test method is incorporated by reference as specified in 40 CFR 52.742.

(vii) ASTM D3980-87: Standard Practice for Interlaboratory Testing of Paint and Related Materials. This practice is incorporated by reference as specified in 40 CFR 52.742.

(viii) ASTM E180-85: Standard Practice for Determining the Precision of ASTM Methods for Analysis of and Testing of Industrial Chemicals. This practice is incorporated by reference as specified in 40 CFR 52.742.

(ix) ASTM D2372-85: Standard Method of Separation of Vehicle from Solvent-reducible Paints. This method is incorporated by reference as specified in 40 CFR 52.742.

(4) Use of an adaptation to any of the analytical methods specified in paragraphs (a)(4)(i)(B)(1), (2) and (3) may be approved by the Administrator on a case-by-case basis. An owner or operator must submit sufficient documentation for the Administrator to find that the analytical methods specified in paragraphs (a)(4)(i)(B)(1), (2) and (3) will yield inaccurate results and that the proposed adaptation is appropriate.

(C) Calculations. Calculations for determining the VOM content, water content and the content of any compounds which are specifically exempted from the definition of VOM of coatings, inks and fountain solutions as applied shall follow the guidance provided in the following documents.

(1) “A Guide for Surface Coating Calculation” EPA-340/1-86-016 (which is available from the National Technical Information Services, 5285 Port Royal Road, Springfield, VA 22161)

(2) “Procedures for Certifying Quantity of Volatile Organic Compounds Emitted by Paint, Ink and Other Coatings” (revised June 1986) EPA-450/3-84-019 (which is available from the National Technical Information Services, 5285 Port Royal Road, Springfield, VA 22161)

(3) “A Guide for Graphic Arts Calculations” August 1988 EPA-340/1-88-003 (which is available from the National Technical Information Services, 5285 Port Royal Road, Springfield, VA 22161)

(ii) Automobile or light-duty truck test protocol. The protocol for testing, including determining the transfer efficiency, of coating applicators at topcoat coating operations at an automobile assembly facility shall follow the procedure in: “Protocol for Determining the Daily Volatile Organic Compound Emission Rate of Automobile and Light-Duty Truck Topcoat Operations” December 1988 EPA-450/3-88-018 (which is available for purchase from the National Technical Information Services, 5285 Port Royal Road, Springfield, VA 22161)

(iii) Capture system efficiency test protocols—(A) Applicability. The requirements of paragraphs (a)(4)(iii)(B) of this section shall apply to all VOM emitting processes employing capture equipment (e.g., hoods, ducts), except those cases noted below.

(1) If a source installs a permanent total enclosure (PTE) that meets USEPA specifications, and which directs all VOM to a control device, then the source is exempted from the requirements described in paragraph (B). The USEPA specifications to determine whether a structure is considered a PTE are given in Procedure T of appendix B of this section. In this instance, the capture efficiency is assumed to be 100 percent and the source is still required to measure control efficiency using appropriate test methods as specified in (a)(4)(iv) of this section.

(2) If a source uses a control device designed to collect and recover VOM (e.g., carbon adsorber), an explicit measurement of capture efficiency is not necessary provided that the conditions given below are met. The overall control of the system can be determined by directly comparing the input liquid VOM to the recovered liquid VOM. The general procedure for use in this situation is given in 40 CFR 60.433, with the following additional restrictions:

(i) The source must be able to equate solvent usage with solvent recovery on a 24-hour (daily) basis, rather than a 30-day weighted average, within 72 hours following the 24-hour period. In addition, one of the following two criteria must be met:

(ii) The solvent recovery system (i.e., capture and control system) must be dedicated to a single process line (e.g., one process line venting to a carbon adsorber system), or

(iii) If the solvent recovery system controls multiple process lines, then the source must be able to demonstrate that the overall control (i.e., the total recovered solvent VOM divided by the sum of liquid VOM input to all process lines venting to the control system) meets or exceeds the most stringent standard applicable for any process line venting to the control system.

(B) Specific requirements. The capture efficiency of a process line shall be measured using one of the four protocols given below. Any error margin associated with a test protocol may not be incorporated into the results of a capture efficiency test. If these techniques are not suitable for a particular process, then the source must present an alternative capture efficiency protocol and obtain approval for it by the Administrator as a SIP or FIP revisions.

(1) Gas/gas method using temporary total enclosure (TTE). The USEPA specifications to determine whether a temporary enclosure is considered a TTE are given in Procedure T of appendix B of this section. The capture efficiency equation to be used for this protocol is:

CE = Gw / (GW + Fw)

Where:

CE = capture efficiency, decimal fraction.

Gw = mass of VOM captured and delivered to control device using a TTE.

Fw = mass of fugitive VOM that escapes from a TTE.

Procedure G.2 contained in appendix B of this section is used to obtain Gw. Procedure F.1 in appendix B of this section is used to obtain Fw.

(2) Liquid/gas method using TTE. The USEPA specifications to determine whether a temporary enclosure is considered a TTE are given in Procedure T of appendix B of this section. The capture efficiency equation to be used for this protocol is:

CE = (L − F) / L

Where:

CE = capture efficiency, decimal fraction.

L = mass of liquid VOM input to process.

Fw = mass of fugitive VOM that escapes from a TTE.

Procedure L contained in appendix B of this section is used to obtain L. Procedure F.1 in appendix B of this section is used to obtain Fw.

(3) Gas/gas method using the building or room (building or room enclosure) in which the affected source is located as the enclosure and in which “F” and “G” are measured while operating only the affected facility. All fans and blowers in the building or room must be operated as they would under normal production. The capture efficiency equation to be used for this protocol is:

CE = G / (G + FB)

Where:

CE = capture efficiency, decimal fraction.

G = mass of VOM captured and delivered to control device.

FB = mass of fugitive VOM that escapes from building enclosure.

Procedure G.2 contained in appendix B of this section is used to obtain G. Procedure F.2 in appendix B of this section is used to obtain FB.

(4) Liquid/gas method using the building or room (building or room enclosure) in which the affected source is located as the enclosure and in which “F” and “L” are measured while operating only the affected facility. All fans and blowers in the building or room must be operated as they would under normal production. The capture efficiency equation to be used for this protocol is:

CE = (L − FB) / L

Where:

CE = capture efficiency, decimal fraction.

L = mass of liquid VOM input to process.

FB = mass of fugitive VOM that escapes from building enclosure.

Procedure L contained in appendix B of this section is used to obtain L. Procedure F.2 in appendix B of this section is used to obtain FB.

(C) Recordkeeping and reporting. (1) All affected facilities must maintain a copy of the capture efficiency protocol submitted to USEPA on file. All results of the appropriate test methods and capture efficiency protocols must be reported to USEPA within sixty (60) days of the test date. A copy of the results must be kept on file with the source for a period of three (3) years.

(2) If any changes are made to capture or control equipment, then the source is required to notify USEPA of these changes and a new test may be required by USEPA.

(3) The source must notify the Administrator 30 days prior to performing any capture efficiency or control test. At that time, the source must notify the Administrator which capture efficiency protocol and control device test methods will be used.

(4) Sources utilizing a PTE must demonstrate that this enclosure meets the requirement given in Procedure T (in appendix B of this section) for a PTE during any testing of their control device.

(5) Sources utilizing a TTE must demonstrate that their TTE meets the requirements given in Procedure T (in appendix B of this section) for a TTE during testing of their control device. The source must also provide documentation that the quality assurance criteria for a TTE have been achieved.

(iv) Control device efficiency testing and monitoring. (A) The control device efficiency shall be determined by simultaneously measuring the inlet and outlet gas phase VOM concentrations and gas volumetric flow rates in accordance with the gas phase test methods specified in paragraph (a)(4)(vi) of this section.

(B) Any owner or operator that uses an afterburner or carbon adsorber to comply with any paragraph of §52.741 shall use USEPA approved continuous monitoring equipment which is installed, calibrated, maintained, and operated according to vendor specifications at all times the afterburner or carbon adsorber is in use. The continuous monitoring equipment must monitor the following parameters:

(1) Combustion chamber temperature of each afterburner.

(2) Temperature rise across each catalytic afterburner bed or VOM concentration of exhaust.

(3) The VOM concentration of each carbon adsorption bed exhaust.

(v) Overall efficiency. (A) The overall efficiency of the emission control system shall be determined as the product of the capture system efficiency and the control device efficiency or by the liquid/liquid test protocol as specified in 40 CFR 60.433 (and revised by paragraph (a)(4)(iii)(A)(2) of this section for each solvent recovery system. In those cases in which the overall efficiency is being determined for an entire line, the capture efficiency used to calculate the product of the capture and control efficiency is the total capture efficiency over the entire line.

(B) For coating lines which are both chosen by the owner or operator to comply with paragraphs (e)(2)(ii), (e)(2)(iii), (e)(2)(iv), (e)(2)(v), or (e)(2)(vi) of this section by the alternative in paragraph (e)(2)(i)(B) of this section and meet the criteria allowing them to comply with paragraph (e)(2) of this section instead of paragraph (e)(1) of this section, the overall efficiency of the capture system and control device, as determined by the test methods and procedures specified in paragraphs (a)(4) (iii), (iv) and (v)(A) of this section, shall be no less than the equivalent overall efficiency which shall be calculated by the following equation:

E = ([VOMa − VOM1]/VOMa) × 100

Where:

E = Equivalent overall efficiency of the capture system and control device as a percentage,

VOMa = Actual VOM content of a coating, or the daily-weighted average VOM content of two or more coatings (if more than one coating is used), as applied to the subject coating line as determined by the applicable test methods and procedures specified in paragraph (a)(4)(i) of this section in units of kg VOM/l (lb VOM/gal) of coating solids as applied,

VOM1 = The VOM emission limit specified in paragraph (e)(2) (i) or (ii) of this section in units of kg VOM/l (lb VOM/gal) of coating solids as applied.

(vi) Volatile organic material gas phase source test methods. The methods in 40 CFR part 60, appendix A, delineated below shall be used to determine control device efficiencies.

(A) 40 CFR part 60, appendix A, Method 18, 25 or 25A, as appropriate to the conditions at the site, shall be used to determine VOM concentration. Method selection shall be based on consideration of the diversity of organic species present and their total concentration and on consideration of the potential presence of interfering gases. Except as indicated in paragraphs (a)(4)(vi)(A)(1) and (2) of this section, the test shall consist of three separate runs, each lasting a minimum of 60 min, unless the Administrator determines that process variables dictate shorter sampling times.

(1) When the method is to be used to determine the efficiency of a carbon adsoption system with a common exhaust stack for all the individual adsorber vessels, the test shall consist of three separate runs, each coinciding with one or more complete sequences through the adsorption cycles of all the individual adsorber vessels.

(2) When the method is to be used to determine the efficiency of a carbon adsorption system with individual exhaust stacks for each adsorber vessel, each adsorber vessel shall be tested individually. The test for each adsorber vessel shall consist of three separate runs. Each run shall coincide with one or more complete adsorption cycles.

(B) 40 CFR part 60, appendix A, Method 1 or 1A shall be used for sample and velocity traverses.

(C) 40 CFR part 60, appendix A, Method 2, 2A, 2C or 2D shall be used for velocity and volumetric flow rates.

(D) 40 CFR part 60, appendix A, Method 3 shall be used for gas analysis.

(E) 40 CFR part 60, appendix A, Method 4 shall be used for stack gas moisture.

(F) 40 CFR part 60, appendix A, Methods 2, 2A, 2C, 2D, 3 and 4 shall be performed, as applicable, at least twice during each test run.

(G) Use of an adaptation to any of the test methods specified in paragraphs (a)(4)(vi) (A), (B), (C), (D), (E), and (F) of this section may be approved by the Administrator on a case-by-case basis. An owner or operator must submit sufficient documentation for the Administrator to find that the test methods specified in paragraphs (a)(4)(vi) (A), (B), (C), (D), (E), and (F) of this section will yield inaccurate results and that the proposed adaptation is appropriate.

(vii) Leak detection methods for volatile organic material. Owners or operators required by the various subparts of this regulation to carry out a leak detection monitoring program shall comply with the following requirements:

(A) Leak detection monitoring. (1) Monitoring shall comply with 40 CFR part 60, appendix A. Method 21.

(2) The detection instrument shall meet the performance criteria of Method 21.

(3) The instrument shall be calibrated before use on each day of its use by the methods specified in Method 21.

(4) Calibration gases shall be:

(i) Zero air (less than 10 ppm of hydrocarbon in air); and

(ii) A mixture of methane or n-hexane and air at a concentration of approximately, but no less than, 10,000 ppm methane or n-hexane.

(5) The instrument probe shall be traversed around all potential leak interfaces as close to the interface as possible as described in Method 21.

(B) When equipment is tested for compliance with no detectable emissions as required, the test shall comply with the following requirements:

(1) The requirements of paragraphs (a)(4) (vii)(A)(1) through (vii)(A)(5) of this section shall apply.

(2) The background level shall be determined as set forth in Method 21.

(C) Leak detection tests shall be performed consistent with:

(1) “APTI Course SI 417 controlling Volatile Organic Compound Emissions from Leaking Process Equipment” EPA-450/2-82-015 (which is available for purchase from the National Technical Information Services, 5285 Port Royal Road, Springfield, VA 22161)

(2) “Portable Instrument User's Manual for Monitoring VOC Sources” EPA-340/1-86-015 (which is available for purchase from the National Technical Information Services, 5285 Port Royal Road, Springfield, VA 22161)

(3) “Protocols for Generating Unit-Specific Emission Estimates for Equipment Leaks of VOC and VHAP” EPA-450/3-88-010 (which is available for purchase from the National Technical Information Services, 5285 Port Royal Road, Springfield, VA 22161)

(4) “Petroleum Refinery Enforcement Manual” EPA-340/1-80-008 (which is available for purchase from the National Technical Information Services, 5285 Port Royal Road, Springfield, VA 22161)

(viii) Bulk gasoline delivery system test protocol. (A) The method for determining the emissions of gasoline from a vapor recovery system are delineated in 40 CFR part 60, subpart XX, §60.503.

(B) Other tests shall be performed consistent with:

(1) “Inspection Manual for Control of Volatile Organic Emissions from Gasoline Marketing Operations: Appendix D” EPA-340/1-80-012 (which is available for purchase from the National Technical Information Services, 5285 Port Royal Road, Springfield, VA 22161)

(2) “Control of Hydrocarbons from Tank Truck Gasoline Loading Terminals: Appendix A” EPA-450/2-77-026 (which is available for purchase from the National Technical Information Services, 5285 Port Royal Road, Springfield, VA 22161)

(5) Compliance dates. Compliance with the requirements of all rules is required by July 1, 1991, unless otherwise indicated by compliance dates contained in specific rules. This paragraph shall not operate to provide additional time for compliance under section 113(d) of the Act, 42 U.S.C. 7413(d), for sources subject to compliance upon promulgation.

(6) Afterburners. The operation of any natural gas fired afterburner and capture system used to comply with §52.741 is not required during the period of November 1 of any year to April 1 of the following year provided that the operation of such devices is not required for purposes of occupational safety or health, or for the control of toxic substances, odor nuisances, or other regulated pollutants.

(7) Exemptions, variances, and alternative means of control or compliance determinations. Notwithstanding the provisions of any other paragraphs of this section, any exemptions, variances or alternatives to the control requirements, emission limitations, or test methods in the Illinois SIP or FIP can only be allowed if approved by the Administrator as a SIP or FIP revision.

(8) Vapor pressure of volatile organic liquids. (i) If the VOL consists of only a single compound, the vapor pressure shall be determined by ASTM Method D2879-86 (incorporated by reference as specified in 40 CFR 52.742) or the vapor pressure may be obtained from a published source such as: Boublik, T., V. Fried and E. Hala, “The Vapor Pressure of Pure Substances,” Elsevier Scientific Publishing Co., New York (1973); Perry's Chemical Engineer's Handbook, McGraw-Hill Book Company (1984); CRC Handbook of Chemistry and Physics, Chemical Rubber Publishing Company (1986-87); and Lange's Handbook of Chemistry, John A. Dean, editor, McGraw-Hill Book Company (1985).

(ii) If the VOL is a mixture, the vapor pressure shall be determined by ASTM Method D2879-86 (incorporated by reference as specified in 40 CFR 52.742) or by the following equation:

eCFR graphic ec07no91.001.gif

View or download PDF

Where:

Pvol = Total vapor pressure of the mixture,

n = Number of components in the mixture,

i = Subscript denoting an individual component,

Pi = Vapor pressure of a component determined in accordance with paragraph (a) of this section

Xi = Mole fraction of the component in the total mixture.

(9) Vapor pressure of organic material or solvent. (i) If the organic material or solvent consists of only a single compound, the vapor pressure shall be determined by ASTM Method D2879-86 (incorporated by reference as specified in 40 CFR 52.742) or the vapor pressure may be obtained from a published source such as: Boublik, T., V. Fried and E. Hala, “The Vapor Pressure of Pure Substances,” Elsevier Scientific Publishing Co., New York (1973); Perry's Chemical Engineer's Handbook, McGraw-Hill Book Company (1984); CRC Handbook of Chemistry and Physics, Chemical Rubber Publishing Company (1986-87); and Lange's Handbook of Chemistry, John A. Dean, editor, McGraw-Hill Book Company (1985).

(ii) If the organic material or solvent is in a mixture made up of both organic material compounds and compounds which are not organic material, the vapor pressure shall be determined by the following equation:

eCFR graphic ec07no91.002.gif

View or download PDF

Where:

Pom = Total vapor pressure of the portion of the mixture which is composed of organic material,

n = Number of organic material components in the mixture,

i = Subscript denoting an individual component,

Pi = Vapor pressure of an organic material component determined in accordance with paragraph (a) of this section,

Xi = Mole fraction of the organic material component of the total mixture.

(iii) If the organic material or solvent is in a mixture made up of only organic material compounds, the vapor pressure shall be determined by ASTM Method D2879-86 (incorporated by reference as specified in 40 CFR 52.742) or by the above equation.

(10) Vapor pressure of volatile organic material. (i) If the VOM consists of only a single compound, the vapor pressure shall be determined by ASTM Method D2879-86 (incorporated by reference as specified in 40 CFR 52.742) or the vapor pressure may be obtained from a published source such as: Boublik, T., V. Fried and E. Hala, “The Vapor Pressure of Pure Substances,” Elsevier Scientific Publishing Co., New York (1973); Perry's Chemical Engineer's Handbook, McGraw-Hill Book Company (1984); CRC Handbook of Chemistry and Physics, Chemical Rubber Publishing Company (1986-87); and Lange's Handbook of Chemistry, John A. Dean, editor, McGraw-Hill Book Company (1985).

(ii) If the VOM is in a mixture made up of both VOM compounds and compounds which are not VOM, the vapor pressure shall be determined by the following equation:

eCFR graphic ec07no91.003.gif

View or download PDF

Where:

Pvom = Total vapor pressure of the portion of the mixture which is composed of VOM,

n = Number of VOM components in the mixture,

i = Subscript denoting an individual component,

Pi = Vapor pressure of a VOM component determined in accordance with paragraph (a) of this section,

Xi = Mole fraction of the VOM component of the total mixture.

(iii) If the VOM is in a mixture made up of only VOM compounds, the vapor pressure shall be determined by ASTM Method D2879-86 (incorporated by reference as specified in 40 CFR 52.742) or by the above equation.

(b)-(c) [Reserved]

(d) Solvent cleaning—(1) Solvent cleaning in general. The requirements of subpart E (sections 215.182-215.184) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742) shall apply to all cold cleaning, open top vapor degreasing, and conveyorized degreasing operations.

Note: For Federal purposes, paragraph (d)(1) supersedes subpart E (section 215.181) of 35 Ill. Adm. Code 215.)

(2) Compliance schedule. Every owner or operator of an emission source which was previously exempt from the requirements of subpart E (sections 215.182-215.184) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742) because it satisfied the criteria in either (d)(a)(i) or (d)(2)(ii) of this section, shall comply with the requirements of subpart E (sections 215.182-215.184) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742) on and after July 1, 1991. A source which did not satisfy the criteria in either (d)(a)(i) or (d)(2)(ii) of this section, shall comply with the requirements of subpart E (sections 215.182-215.184) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742) upon promulgation.

(i) If emissions of VOM exceed neither 6.8 kg (15 lbs) in any one day, nor 1.4 kg (3 lbs) in any one hour, or

(ii) If the source is used exclusively for chemical or physical analysis or for determination of product quality and commercial acceptance, provided that the operation of the source is not an integral part of the production process, the emissions of VOM from the source do not exceed 363 kg (800 lbs) in any calendar month, and the exemption had been approved in writing by the Illinois Environmental Protection Agency.

(3) Test methods. The following test methods shall be used to demonstrate compliance with subpart E (sections 215.182-215.184) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742):

(i) Vapor pressures shall be determined by using the procedure specified in paragraph (a)(9) of this section.

(ii) Exhaust ventilation rates shall be determined by using the procedures specified in paragraph (a)(4)(vi)(C) of this section.

(iii) The performance of control devices shall be determined by using the procedures specified in paragraph (a)(4)(vi) of this section.

(e) Coating operations—(1) Emission limitations for manufacturing plants. (i) Except as provided in paragraph (e)(3) of this section, no owner or operator of a coating line shall apply at any time any coating in which the VOM content exceeds the following emission limitations for the specified coating. The following emission limitations are expressed in units of VOM per volume of coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied at each coating applicator, except where noted. Compounds which are specifically exempted from the definition of VOM should be treated as water for the purpose of calculating the “less water” part of the coating composition. Compliance with this paragraph must be demonstrated through the applicable coating analysis test methods and procedures specified in paragraph (a)(4)(i) of this section and the recordkeeping and reporting requirements specified in paragraph (e)(6)(ii) of this section. As an alternative to compliance with this paragraph, the owner or operator of a coating line may meet the requirements of paragraph (e)(1)(ii) or paragraph (e)(2) of this section. The equation presented in paragraph (e)(1)(iii) of this section shall be used to calculate emission limitations for determining compliance by add-on controls, credits for transfer efficiency, emissions trades and cross-line averaging.

   kg/l lb/gal
(A) Automobile or Light-Duty Truck Coating
(1) Prime coat0.14(1.2)
(2) Prime surfacer coat0.34(2.8)
Note: The prime surfacer coat limitation is based upon a transfer efficiency of 30 percent. Transfer efficiency credits can only be allowed if approved by the Administrator as a SIP or FIP revision.
(3) Topcoat1.81(15.1)
Note: The topcoat limitation is in units of kg (lbs) of VOM per l (gal) of coating solids deposited. Compliance with the limitation shall be based on the daily-weighted average VOM content from the entire topcoat operation (all topcoat spray booths, flash-off areas and bake ovens). Compliance shall be demonstrated in accordance with the topcoat protocol for automobiles and light-duty trucks referenced in paragraph (a)(4)(ii) of this section. Paragraph (e)(1)(ii) of this section does not apply to the topcoat limitation.) At least 180 days prior to the initial compliance date, the owner or operator of a coating line subject to the topcoat limitation shall submit to the Administrator a detailed proposal specifying the method of demonstrating compliance with the protocol. The proposal shall include, at a minimum, a comprehensive plan (including a rationale) for determining the transfer efficiency at each booth through the use of in-plant, or pilot testing; the selection of coatings to be tested (for the purpose of determining transfer efficiency) including the rationale for coating groupings; and the method for determining the analytic VOM content of as applied coatings and the formulation solvent content of as applied coatings. Upon approval of the protocol by the Administrator, the source may proceed with the compliance demonstration.
(4) Final repair coat0.58(4.8)
(B) Can Coating
(1) Sheet basecoat and overvarnish0.34(2.8)
(2) Exterior basecoat and overvarnish0.34(2.8)
(3) Interior body spray coat0.51(4.2)
(4) Exterior end coat0.51(4.2)
(5) Side seam spray coat0.66(5.5)
(6) End sealing compound coat0.44(3.7)
(C) Paper Coating0.35(2.9)
Note: The paper coating limitation shall not apply to any owner or operator of any paper coating line on which printing is performed if the paper coating line complies with the emissions limitations in paragraph (h)(1) of this section: Printing and Publishing.
(D) Coil Coating0.31(2.6)
(E) Fabric Coating0.35(2.9)
(F) Vinyl Coating0.45(3.8)
(G) Metal Furniture Coating0.36(3.0)
(H) Large Appliance Coating0.34(2.8)
Note: The limitation shall not apply to the use of quick-drying lacquers for repair of scratches and nicks that occur during assembly, provided that the volume of coating does not exceed 0.95 l (1 quart) in any one rolling eight-hour period.
(I) Magnet Wire Coating0.20(1.7)
(J) Miscellaneous Metal Parts and Products Coating
(1) Clear coating0.52(4.3)
(2) Air-dried coating0.42(3.5)
(3) Extreme performance coating0.42(3.5)
(4) Steel pail and drum interior coating0.52(4.3)
(5) All other coatings0.36(3.0)
   kg/l lb/gal
(K) Heavy Off-Highway Vehicle Products Coating
(1) Extreme performance prime coat0.42(3.5)
(2) Extreme performance top-coat (air dried)0.42(3.5)
(3) Final repair coat (air dried)0.42(3.5)
(4) All other coatings are subject to the emission limitations for miscellaneous metal parts and products coatings in paragraph (e)(1)(i)(J) of this section.
(L) Wood Furniture Coating
(1) Clear topcoat0.67(5.6)
(2) Opaque stain0.56(4.7)
(3) Pigmented coat0.60(5.0)
(4) Repair coat0.67(5.6)
(5) Sealer0.67(5.6)
(6) Semi-transparent stain0.79(6.6)
(7) Wash coat0.73(6.1)
Note: An owner or operator of a wood furniture coating operation subject to this paragraph shall apply all coatings, with the exception of no more than 37.8 l (10 gal) of coating per day used for touch-up and repair operations, using one or more of the following application systems: airless spray application system, air-assisted airless spray application system, electrostatic spray application system, electrostatic bell or disc spray application system, heated airless spray application system, roller coating, brush or wipe coating application system, or dip coating application system.
(M) Existing Diesel-Electric Locomotive Coating Lines in Cook County
(1) Extreme performance prime coat0.42(3.5)
(2) Extreme performance top-coat (air dried)0.42(3.5)
(3) Final repair coat (air dried)0.42(3.5)
(4) High-temperature aluminum coating0.72(6.0)
(5) All other coatings0.36(3.0)

(ii) Daily-weighted average limitations. No owner or operator of a coating line subject to the limitations of paragraph (e)(1)(i) of this section and complying by means of paragraph (e)(1)(ii) of this section shall operate the subject coating line unless the owner or operator has demonstrated compliance with paragraph (e)(1) (ii)(A), (ii)(B), (ii)(C), (ii)(D), (ii)(E) or (ii)(F) of this section (depending upon the source category) through the applicable coating analysis test methods and procedures specified in paragraph (a)(4)(i) of this section and the recordkeeping and reporting requirements specified in paragraph (e)(6)(iii) of this section.

(A) No owner or operator of a coating line subject to only one of the limitations from among paragraph (e)(1) (i)(A)(1), (i)(A)(2), (i)(A)(4), (i)(C), (i)(D), (i)(E), (i)(F), (i)(G), (i)(H), or (i)(I) of this section shall apply coating on any such coating line, during any day, whose daily-weighted average VOM content exceeds the emission limitation to which the coatings are subject.

(B) No owner or operator of a miscellaneous metal parts and products coating line subject to the limitations of paragraph (e)(1)(i)(J) of this section shall apply coatings to miscellaneous metal parts or products on the subject coating line unless the requirements in paragraph (e)(1)(ii)(B) (1) or (2) of this section are met.

(1) For each coating line which applies multiple coatings, all of which are subject to the same numerical emission limitation within paragraph (e)(1)(i)(J) of this section, during the same day (e.g., all coatings used on the line are subject to 0.42 kg/l [3.5 lbs/gal]), the daily-weighted average VOM content shall not exceed the coating VOM content limit corresponding to the category of coating used, or

(2) For each coating line which applies coatings from more than one of the four coating categories in paragraph (e)(1)(i)(J) of this section, during the same day, the owner or operator shall submit to and receive approval from the Administrator for a site-specific FIP revision. To receive approval, the requirements of USEPA's Emissions Trading Policy Statement (and related policy) must be satisfied.

(C) No owner or operator of a can coating facility subject to the limitations of paragraph (e)(1)(i)(B) of this section shall operate the subject coating facility using a coating with a VOM content in excess of the limitations specified in paragraph (e)(1)(i)(B) of this section unless all of the following requirements are met:

(1) An alternative daily emission limitation shall be determined according to paragraph (e)(1)(ii)(C)(2) of this section. Actual daily emissions shall never exceed the alternative daily emission limitation and shall be calculated by use of the following equation.

eCFR graphic ec07no91.004.gif

View or download PDF

Where:

Ed = Actual VOM emissions for the day in units of kg/day (lbs/day),

i = Subscript denoting a specific coating applied,

n = Total number of coatings applied in the can coating operation,

Vi = Volume of each coating applied for the day in units of l/day (gal/day) of coating (minus water and any compounds which are specifically exempted from the definition of VOM), and

Ci = The VOM content of each coating as applied in units of kg VOM/l (lbs VOM/gal) of coating (minus water and any compounds which are specifically exempted from the definition of VOM).

(2) The alternative daily emission limitation (Ad) shall be determined on a daily basis as follows:

eCFR graphic ec07no91.005.gif

View or download PDF

Where:

Ad = The VOM emissions allowed for the day in units of kg/day (lbs/day),

i = Subscript denoting a specific coating applied,

n = Total number of surface coatings applied in the can coating operation,

Ci = The VOM content of each surface coating as applied in units of kg VOM/l (lbs VOM/gal) of coating (minus water and any compounds which are specifically exempted from the definition of VOM),

Di = The density of VOM in each coating applied. For the purposes of calculating Ad, the density is 0.882 kg VOM/l VOM (7.36 lbs VOM/gal VOM),

Vi = Volume of each surface coating applied for the day in units of l (gal) of coating (minus water and any compounds which are specifically exempted from the definition of VOM),

Li = The VOM emission limitation for each surface coating applied as specified in paragraph (e)(1)(i)(B) of this section in units of kg VOM/l (lbs VOM/gal) of coating (minus water and any compounds which are specifically exempted from the definition of VOM).

(D) No owner or operator of a heavy off-highway vehicle products coating line subject to the limitations of paragraph (e)(1)(i)(K) of this section shall apply coatings to heavy off-highway vehicle products on the subject coating line unless the requirements of paragraph (e)(1)(ii)(D) (1) or (2) of this section are met.

(1) For each coating line which applies multiple coatings, all of which are subject to the same numerical emission limitation within paragraph (e)(1)(i)(K) of this section, during the same day (e.g., all coatings used on the line are subject to 0.42 kg/l [3.5 lbs/gal]), the daily-weighted average VOM content shall not exceed the coating VOM content limit corresponding to the category of coating used, or

(2) For each coating line which applies coatings subject to more than one numerical emission limitation in paragraph (e)(1)(i)(K) of this section, during the same day, the owner or operator shall submit to and receive approval from the Administrator for a site-specific FIP revision. To receive approval, the requirements of USEPA's Emissions Trading Policy Statement (and related policy) must be satisfied.

(E) No owner or operator of a wood furniture coating line subject to the limitations of paragraph (e)(1)(i)(L) of this section shall apply coatings to wood furniture on the subject coating line unless the requirements of paragraph (e)(1)(ii)(E) (1) or (2) of this section, in addition to the requirements specified in the note to paragraph (e)(1)(i)(L) of this section, are met.

(1) For each coating line which applies multiple coatings, all of which are subject to the same numerical emission limitation within paragraph (e)(1)(i)(L) of this section, during the same day (e.g., all coatings used on the line are subject to 0.67 kg/l [5.6 lbs/gal]), the daily-weighted average VOM content shall not exceed the coating VOM content limit corresponding to the category of coating used, or

(2) For each coating line which applies coatings subject to more than one numerical emission limitation in paragraph (e)(1)(i)(L) of this section, during the same day, the owner or operator shall submit to and receive approval from the Administrator for a site-specific FIP revision. To receive approval, the requirements of USEPA's Emissions Trading Policy Statement (and related policy) must be satisfied.

(F) No owner or operator of an existing diesel-electric locomotive coating line in Cook County, subject to the limitations of paragraph (e)(1)(i)(M) of this section shall apply coatings to diesel-electric locomotives on the subject coating line unless the requirements of paragraph (e)(1)(ii)(F) (1) or (2) of this section are met.

(1) For each coating line which applies multiple coatings, all of which are subject to the same numerical emission limitation within paragraph (e)(1)(i)(M) of this section, during the same day (e.g., all coatings used on the line are subject to 0.42 kg/l [3.5 lbs/gal]), the daily-weighted average VOM content shall not exceed the coating VOM content limit corresponding to the category of coating used, or

(2) For each coating line which applies coatings subject to more than one numerical emission limitation in paragraph (e)(1)(i)(M) of this section, during the same day, the owner or operator shall submit to and receive approval from the Administrator for a site-specific FIP revision. To receive approval, the requirements of USEPA's Emissions Trading Policy Statement (and related policy) must be satisfied.

(iii) Limitations in terms of kg (lbs) of VOM emissions per l (gal) of solids as applied at each coating applicator shall be determined by the following equation:

eCFR graphic ec07no91.006.gif

View or download PDF

Where:

S = The limitation on VOM emissions in terms of kg VOM/l (lbs VOM/gal) of solids,

C = The limitation on VOM emissions in terms of kg/l (lbs/gal) of coating (minus water and any compounds which are specifically excluded from the definition of VOM) specified in paragraph (e)(1)(i) of this section,

D = The density of VOM in the coating. For the purposes of calculating S, the density is 0.882 kg VOM/l VOM (7.36 lbs VOM/gal VOM).

(2) Alternative emission limitations. Any owner or operator of a coating line subject to paragraph (e)(1) of this section may comply with this paragraph, rather than with paragraph (e)(1) of this section, if a capture system and control device are operated at all times and the owner or operator demonstrates compliance with paragraphs (e)(2) (ii), (iii), (iv), (v), (vi) or (vii) of this section (depending upon the source category) through the applicable coating analysis and capture system and control device efficiency test methods and procedures specified in paragraph (a)(4) of this section and the recordkeeping and reporting requirements specified in paragraph (e)(6)(iv) of this section; and the control device is equipped with the applicable monitoring equipment specified in paragraph (a)(4)(iv) of this section and the monitoring equipment is installed, calibrated, operated and maintained according to vendor specifications at all times the control device is in use. The use of a capture system and control device, which does not demonstrate compliance with paragraph (e)(2) (ii), (iii), (iv), (v), (vi), or (vii), may only be used as an alternative to compliance with paragraph (e)(1) of this section if approved as a FIP revision.

(i) Alternative add-on control methodologies. (A) The coating line is equipped with a capture system and control device that provides 81 percent reduction in the overall emissions of VOM from the coating line and the control device has a 90 percent efficiency, or

(B) The system used to control VOM from the coating line is demonstrated to have an overall efficiency sufficient to limit VOM emissions to no more than what is allowed under paragraph (e)(1) of this section. Use of any control system other than an afterburner, carbon absorption, condensation, or absorption scrubber system can only be allowed if approved by the Administrator as a SIP or FIP revision. Transfer efficiency credits can only be allowed if approved by the Administrator as a SIP or FIP revision. Baseline transfer efficiencies and transfer efficiency test methods must be approved by the Administrator.

Such overall efficiency is to be determined as follows:

(1) Obtain the emission limitation from the appropriate paragraph in (e)(1) of this section,

(2) Calculate “S” according to the equation in paragraph (e)(1)(iii) of this section,

(3) Calculate the overall efficiency required according to paragraph (a)(4)(v) of this section. For the purposes of calculating this value, according to the equation in (a)(4)(v)(B) of this section VOM1 is equal to the value of “S” as determined above in (i)(B)(2).

(ii) No owner or operator of a coating line subject to only one of the emission limitations from among paragraph (e)(1)(i)(A)(1), (e)(1)(i)(A)(2), (e)(1)(i)(A)(4), (e)(1)(i)(C), (e)(1)(i)(D), (e)(1)(i)(E), (e)(1)(i)(F), (e)(1)(i)(G), (e)(1)(i)(H), or (e)(1)(i)(I) of this section and equipped with a capture system and control device shall operate the subject coating line unless the requirements in paragraph (e)(2)(i) (A) or (B) of this section are met. No owner or operator of a coating line subject to paragraph (e)(1)(i)(A)(3) of this section and equipped with a capture system and control device shall operate the coating line unless the owner or operator demonstrates compliance with the topcoat limitation in accordance with the topcoat protocol for automobile or light-duty trucks referenced in paragraph (a)(4)(ii) of this section.

(iii) No owner or operator of a miscellaneous metal parts and products coating line which applies one or more coatings during the same day, all of which are subject to the same numerical emission limitation within paragraph (e)(1)(i)(J) of this section (e.g., all coatings used on the line are subject to 0.42 kg/l [3.5 lbs/gal]), and which is equipped with a capture system and control device shall operate the subject coating line unless the requirements in paragraph (e)(2)(i) (A) or (B) of this section are met.

(iv) No owner or operator of a heavy off-highway vehicle products coating line which applies one or more coatings during the same day, all of which are subject to the same numerical emission limitation within paragraph (e)(1)(i)(K) of this section (e.g., all coatings used on the line are subject to 0.42 kg/l [3.5 lbs/gal]), and which is equipped with a capture system and control device shall operate the subject coating line unless the requirements in paragraph (e)(2)(i) (A) or (B) of this section are met.

(v) No owner or operator of an existing diesel-electric locomotive coating line in Cook County which applies one or more coatings during the same day, all of which are subject to the same numerical emission limitation within paragraph (e)(1)(i)(M) of this section (e.g., all coatings used on the line are subject to 0.42 kg/l [3.5 lbs/gals]), and which is equipped with a capture system and control device shall operate the subject coating line unless the requirements in paragraph (e)(2)(i) (A) or (B) of this section are met.

(vi) No owner or operator of a wood furniture coating line which applies one or more coatings during the same day, all of which are subject to the same numerical emission limitation within paragraph (e)(1)(i)(L) (e.g., all coatings used on the line are subject to 0.67 kg/l [5.6 lbs/gal]), and which is equipped with a capture system and control device shall operate the subject coating line unless the requirements in paragraph (e)(2)(i) (A) or (B) of this section are met. If compliance is achieved by meeting the requirements in paragraph (e)(2)(i)(B) of this section, then the provisions in the note to paragraph (e)(1)(i)(L) of this section must also be met.

(vii) No owner or operator of a can coating facility and equipped with a capture system and control device shall operate the subject coating facility unless the requirements in paragraph (e)(2)(vii) (A) or (B) of this section are met.

(A) An alternative daily emission limitation shall be determined according to paragraph (e)(1)(ii)(C)(2) of this section. Actual daily emissions shall never exceed the alternative daily emission limitation and shall be calculated by use of the following equation:

eCFR graphic ec07no91.007.gif

View or download PDF

Where:

Ed = Actual VOM emissions for the day in units of kg/day (lbs/day),

i = Subscript denoting the specific coating applied,

n = Total number of surface coatings as applied in the can coating operation,

Vi = Volume of each coating as applied for the day in units of 1/day (gal/day) of coating (minus water and any compounds which are specifically exempted from the definition of VOM),

Ci = The VOM content of each coating as applied in units of kg VOM/l (lbs VOM/gal) of coating (minus water and any compounds which are specifically exempted from the definition of VOM), and

Fi = Fraction, by weight, of VOM emissions from the surface coating, reduced or prevented from being emitted to the ambient air. This is the overall efficiency of the capture system and control device.

(B) The coating line is equipped with a capture system and control device that provide 75 percent reduction in the overall emissions of VOM from the coating line and the control device has a 90 percent efficiency.

(3) Exemptions from emission limitations—(i) Exemptions for all source categories except wood furniture coating. The limitations of paragraph (e) of this section shall not apply to coating lines within a facility, that otherwise would be subject to the same subparagraph of paragraph (e)(1)(i) of this section (because they belong to the same source category, e.g. can coating), provided that combined actual emissions of VOM from all lines at the facility subject to that subparagraph never exceed 6.8 kg/day (15 lbs/day) before the application of capture systems and control devices. (For example, can coating lines within a plant would not be subject to the limitations of subparagraph (e)(1)(i)(B) of this section if the combined actual emissions of VOM from the can coating lines never exceed 6.8 kg/day (15 lbs/day) before the application of capture systems and control devices.) Volatile organic material emissions from heavy off-highway vehicle products coating lines must be combined with VOM emissions from miscellaneous metal parts and products coating lines to determine applicability. Any owner or operator of a coating facility shall comply with the applicable coating analysis test methods and procedures specified in paragraph (a)(4)(i) of this section and the recordkeeping and reporting requirements specified in paragraph (e)(6)(i) of this section if total VOM emissions from the subject coating lines are always less than or equal to 6.8 kg/day (15 lbs/day) before the application of capture systems and control devices and, therefore, are not subject to the limitations of paragraph (e)(1) of this section. Once a category of coating lines at a facility is subject to the limitations in paragraph (e)(1) of this section, the coating lines are always subject to the limitations in paragraph (e)(1) of this section.

(ii) Applicability for wood furniture coating. (A) The limitations of paragraph (e) of this section shall apply to a plant's wood furniture coating lines if the plant contains process emission sources, not regulated by paragraphs (d), (e) (excluding paragraph (e)(1)(i)(L)), (h) (excluding paragraph (h)(5)), (i), (j), or (q)(1), or subparts B, Q (excluding sections 215.432 and 215.436), R (excluding sections 215.447, 215.450, and 215.452), S, V, X, Y (sections 215.582-215.584), or Z of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), which as a group both:

(1) Have maximum theoretical emissions of 91 Mg (100 tons) or more per calendar year of VOM if no air pollution control equipment were used, and

(2) Are not limited to less than 91 Mg (100 tons) of VOM per calendar year if no air pollution control equipment were used, through production or capacity limitations contained in a federally enforceable construction permit or SIP or FIP version.

(B) If a plant ceases to fulfill the criteria of paragraph (e)(3)(ii)(A) of this section, the limitations of paragraph (e)(1)(i)(L) of this section shall continue to apply to any wood furniture coating line which was ever subject to the limitations of paragraph (e)(1)(i)(L) of this section.

(C) For the purposes of paragraph (e)(3)(ii) of this section, an emission source shall be considered regulated by a subpart (of the Illinois rules), section, or paragraph if it is subject to the limitations of that subpart (of the Illinois rules), section, or paragraph. An emission source is not considered regulated by a subpart (of the Illinois rules), section, or paragraph if its emissions are below the applicability cutoff level or if the source is covered by an exemption.

(D) Any owner or operator of a wood furniture coating line to which the limitations of paragraph (e) of this section are not applicable due to the criteria in paragraph (e)(3)(ii) of this section shall, upon request by the Administrator, submit records to the Administrator within 30 calendar days from the date of the request that document that the coating line is exempt from the limitations of paragraph (e) of this section.

(4) Exemption from general rule on use of organic material. No owner or operator of a coating line subject to the limitations of paragraph (e)(1) of this section is required to meet the limitations of subpart K (section 215.301 or 215.302) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), after the date by which the coating line is required to meet paragraph (e)(1) of this section.

(5) Compliance schedule. Except as specified in paragraph (e)(7) of this section, every owner or operator of a coating line (of a type included within paragraph (e)(1)(i) of this section) shall comply with the requirements of paragraph (e)(1),(e)(2) or (e)(3) of this section and paragraph (e)(6) of this section in accordance with the appropriate compliance schedule as specified in paragraph (e)(5)(i),(ii),(iii) or (iv) of this section.

(i) No owner or operator of a coating line which is exempt from the limitations of paragraph (e)(1) of this section because of the criteria in paragraph (e)(3)(i) of this section shall operate said coating line on or after July 1, 1991, unless the owner or operator has complied with, and continues to comply with, paragraph (e)(6)(i) of this section. Wood furniture coating lines are not subject to paragraph (e)(6)(i) of this section.

(ii) No owner or operator of a coating line complying by means of paragraph (e)(1)(i) of this section shall operate said coating line on or after July 1, 1991, unless the owner or operator has complied with, and continues to comply with, paragraphs (e)(1)(i) and (e)(6)(ii) of this section.

(iii) No owner or operator of a coating line complying by means of paragraph (e)(1)(ii) of this section shall operate said coating line on or after July 1, 1991, unless the owner or operator has complied with, and continues to comply with, paragraphs (e)(1)(ii) and (e)(6)(iii) of this section.

(iv) No owner or operator of a coating line complying by means of paragraph (e)(2) of this section shall operate said coating line on or after July 1, 1991, unless the owner or operator has complied with, and continues to comply with, paragraphs (e)(2) and (e)(6)(iv) of this section.

(6) Recordkeeping and reporting. The VOM content of each coating and the efficiency of each capture system and control device shall be determined by the applicable test methods and procedures specified in paragraph (a)(4) of this section to establish the records required under paragraph (e)(6) of this section.

(i) Any owner or operator of a coating line which is exempted from the limitations of paragraph (e)(1) of this section because of paragraph (e)(3)(i) of this section shall comply with the following:

(A) By July 1, 1991, the owner or operator of a facility referenced in paragraph (e)(6)(i) of this section shall certify to the Administrator that the facility is exempt under the provisions of paragraph (e)(3)(i) of this section. Such certification shall include:

(1) A declaration that the facility is exempt from the limitations of paragraph (e)(1) of this section because of paragraph (e)(3)(i) of this section; and

(2) Calculations which demonstrate that the combined VOM emissions from all coating lines at the facility never exceed 6.8 kg (15 lbs) per day before the application of capture systems and control devices. The following equation shall be used to calculate total VOM emissions:

eCFR graphic ec07no91.008.gif

View or download PDF

Where:

Te = Total VOM emissions from coating lines at a facility each day before the application of capture systems and control devices in units of kg/day (lbs/day),

m = Number of coating lines at the facility,

j = Subscript denoting an individual coating line,

n = Number of different coatings as applied each day on each coating line at the facility,

i = Subscript denoting an individual coating,

Ai = Weight of VOM per volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each day on each coating line at the facility in units of kg VOM/l (lbs VOM/gal), and

Bi = Volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each day on each coating line at the facility in units of l/day (gal/day). The instrument or method by which the owner or operator accurately measured or calculated the volume of each coating as applied on each coating line each day shall be described in the certification to the Administrator.

(B) On and after July 1, 1991, the owner or operator of a facility referenced in paragraph (e)(6)(i) of this section shall collect and record all of the following information each day for each coating line and maintain the information at the facility for a period of three years:

(1) The name and identification number of each coating as applied on each coating line.

(2) The weight of VOM per volume and the volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each day on each coating line.

(C) On and after July 1, 1991, the owner or operator of a facility exempted from the limitations of paragraph (e)(1) of this section because of paragraph (e)(3)(i) of this section shall notify the Administrator of any record showing that total VOM emissions from the coating facility exceed 6.8 kg (15 lbs) in any day before the application of capture systems and control devices shall be reported by sending a copy of such record to the Administrator within 30 days after the exceedance occurs.

(ii) Any owner or operator of a coating line subject to the limitations of paragraph (e)(1) of this section and complying by means of paragraph (e)(1)(i) of this section shall comply with the following:

(A) By July 1, 1991, or upon initial start-up of a new coating line, or upon changing the method of compliance from an existing subject coating line from paragraph (e)(1)(ii) or paragraph (e)(2) to paragraph (e)(1)(i) of this section; the owner or operator of a subject coating line shall certify to the Administrator that the coating line will be in compliance with paragraph (e)(1)(i) of this section on and after July 1, 1991, or on and after the initial start-up date. Such certification shall include:

(1) The name and identification number of each coating as applied on each coating line.

(2) The weight of VOM per volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each day on each coating line.

(3) For coating lines subject to paragraph (e)(1)(i)(A)(3) of this section, certification shall include:

(i) The name and identification number of each coating line which will comply by means of paragraph (e)(1)(i)(A)(3) of this section,

(ii) The name and identification number of each coating as applied on each coating line,

(iii) The weight of VOM per volume of each coating as applied on each coating line,

(iv) The instrument or method by which the owner or operator will accurately measure or calculate the volume of each coating as applied each day on each coating line,

(v) The method by which the owner or operator will create and maintain records each day as required in paragraph (e)(6)(ii)(B) of this section for coating lines subject to paragraph (e)(1)(i)(A)(3) of this section,

(vi) An example format in which the records required in paragraph (e)(6)(ii)(B) of this section for coating lines subject to paragraph (e)(1)(i)(A)(3) of this section.

(B) On and after July 1, 1991, or on and after the initial start-up date, the owner or operator of a coating line subject to the limitations of paragraph (e)(1) of this section and complying by means of paragraph (e)(1)(i) of this section shall collect and record all of the following information each day for each coating line and maintain the information at the facility for a period of three years:

(1) The name and identification number of each coating as applied on each coating line.

(2) The weight of VOM per volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each day on each coating line.

(3) For coating lines subject to paragraph (e)(1)(i)(A)(3) of this section, the owner or operator shall maintain all records necessary to calculate the daily-weighted average VOM content from the coating line in accordance with the proposal submitted, and approved by the Administrator, pursuant to paragraph (e)(1)(A)(3) of this section.

(C) On and after July 1, 1991, the owner or operator of a subject coating line shall notify the Administrator in the following instances:

(1) Any record showing violation of paragraph (e)(1)(i) of this section shall be reported by sending a copy of such record to the Administrator within 30 days following the occurrence of the violation, except that any record showing a violation of paragraph (e)(1)(i)(A)(3) of this section shall be reported by sending a copy of such record to the Administrator within 15 days from the end of the month in which the violation occurred.

(2) At least 30 calendar days before changing the method of compliance with paragraph (e)(1) of this section from paragraph (e)(1)(i) to paragraph (e)(1)(ii) or paragraph (e)(2) of this section, the owner or operator shall comply with all requirements of paragraph (e)(6) (iii)(A) or (iv)(A) of this section, respectively. Upon changing the method of compliance with paragraph (e)(1) of this section from paragraph (e)(1)(i) to paragraph (e)(1)(ii) or paragraph (e)(2) of this section, the owner or operator shall comply with all requirements of paragraph (e)(6) (iii) or (iv) of this section, respectively.

(3) For coating lines subject to paragraph (e)(1)(i)(A)(3) of this section, the owner or operator shall notify the Administrator of any change to the topcoating operation at least 30 days before the change is effected. The Administrator shall determine whether or not recertification testing is required. If the Administrator determines that recertification testing is required, then the owner or operator shall submit a proposal to the Administrator to test within 30 days and retest within 30 days of the Administrator's approval of the proposal.

(iii) Any owner or operator of a coating line subject to the limitations of paragraph (e)(1) of this section and complying by means of paragraph (e)(1)(ii) of this section shall comply with the following:

(A) By July 1, 1991, or upon initial start-up of a new coating line, or upon changing the method of compliance for an existing subject coating line from paragraph (e)(1)(i) or paragraph (e)(2) to paragraph (e)(1)(ii) of this section; the owner or operator of the subject coating line shall certify to the Administrator that the coating line will be in compliance with paragraph (e)(1)(ii) of this section on and after July 1, 1991, or on and after the initial start-up date. Such certification shall include:

(1) The name and identification number of each coating line which will comply by means of paragraph (e)(1)(ii) of this section.

(2) The name and identification number of each coating as applied on each coating line.

(3) The weight of VOM per volume and the volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each day on each coating line.

(4) The instrument or method by which the owner or operator will accurately measure or calculate the volume of each coating as applied each day on each coating line.

(5) The method by which the owner or operator will create and maintain records each day as required in paragraph (e)(6)(iii)(B) of this section.

(6) An example of the format in which the records required in paragraph (e)(6)(iii)(B) of this section will be kept.

(B) On and after July 1, 1991, or on and after the initial start-up date, the owner or operator of a coating line subject to the limitations of paragraph (e)(1) of this section and complying by means of paragraph (e)(1)(ii) of this section, shall collect and record all of the following information each day for each coating line and maintain the information at the facility for a period of three years:

(1) The name and identification number of each coating as applied on each coating line.

(2) The weight of VOM per volume and the volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each day on each coating line.

(3) The daily-weighted average VOM content of all coatings as applied on each coating line as defined in paragraph (a)(3) of this section.

(C) On and after July 1, 1991, the owner or operator of a subject coating line shall notify the Administrator in the following instances:

(1) Any record showing violation of paragraph (e)(1)(ii) of this section shall be reported by sending a copy of such record to the Administrator within 30 days following the occurrence of the violation.

(2) At least 30 calendar days before changing the method of compliance with paragraph (e) from paragraph (e)(1)(ii) to paragraph (e)(1)(i) or paragraph (e)(2) of this section, the owner or operator shall comply with all requirements of paragraph (e)(6)(ii)(A) or (iv)(A), respectively. Upon changing the method of compliance with paragraph (e) from paragraph (e)(1)(ii) to paragraph (e)(1)(i) or paragraph (e)(2) of this section, the owner or operator shall comply with all requirements of paragraph (e)(6)(ii) or (iv), respectively.

(iv) Any operator or owner of a coating line subject to the limitations of paragraph (e)(2) of this section and complying by means of paragraph (e)(2)(ii), (iii), (iv), (v), (vi) or (vii) of this section shall comply with the following:

(A) By July 1, 1991, or upon initial start-up of a new coating line, or upon changing the method of compliance for an existing coating line from paragraph (e)(1) (i) or (ii) to paragraph (e)(2) of this section; the owner or operator of the subject coating line shall perform all tests and submit to the Administrator the results of all tests and calculations necessary to demonstrate that the subject coating line will be in compliance with paragraph (e)(2) of this section on and after July 1, 1991, or on and after the initial start-up date.

(B) On and after July 1, 1991, or on and after the initial start-up date, the owner or operator of a coating line subject to the limitations of paragraph (e)(2) of this section and complying by means of paragraph (e)(2) (ii), (iii), (iv), (v), (vi) or (vii) of this section shall collect and record all of the following information each day for each coating line and maintain the information at the facility for a period of three years:

(1) The weight of VOM per volume of coating solids as applied each day on each coating line, if complying pursuant to paragraph (e)(2)(i)(B) of this section.

(2) Control device monitoring data.

(3) A log operating time for the capture system, control device, monitoring equipment and the associated coating line.

(4) A maintenance log for the capture system, control device and monitoring equipment detailing all routine and non-routine maintenance performed including dates and duration of any outages.

(C) On and after July 1, 1991, the owner or operator of a subject coating line shall notify the Administrator in the following instances:

(1) Any record showing violation of paragraph (e)(2) of this section shall be reported by sending a copy of such record to the Administrator within 30 days following the occurrence of the violation.

(2) At least 30 calendar days before changing the method of compliance with paragraph (e) from paragraph (e)(2) to paragraph (e)(1)(i) or paragraph (e)(1)(ii) of this section, the owner or operator shall comply with all requirements of paragraph (e)(6)(ii)(A) or (iii)(A) of this section, respectively. Upon changing the method of compliance with paragraph (e) from paragraph (e)(2) to paragraph (e)(1)(i) or paragraph (e)(1)(ii) of this section, the owner or operator shall comply with all requirements of paragraph (e)(6)(ii) or (iii) of this section, respectively.

(7) Compliance schedule for diesel electric locomotive coatings. Notwithstanding any other provision of this subpart, the compliance date for the emission limitations and standards for “topcoat” and “final repair coat” operations only as applied to General Motors Corporation at their diesel electric locomotive coating lines in Cook County, Illinois, codified at 40 CFR 52.741(e)(1)(i)(M) (2) and (3) is specified in this paragraph (e)(7). Compliance with the requirements of paragraph (e)(1), (e)(2) or (e)(3) of this section and paragraph (e)(6) of this section must be in accordance with the appropriate compliance schedule as specified in paragraph (e)(7)(i),(ii),(iii), or (iv) of this section.

(i) No owner or operator of a coating line which is exempt from the limitations of paragraph (e)(1) of this section because of the criteria in paragraph (e)(3)(i) of this section shall operate said coating line on or after March 25, 1995, unless the owner or operator has complied with, and continues to comply with, paragraph (e)(6)(i) of this section.

(ii) No owner or operator of a coating line complying by means of paragraph (e)(1)(i) of this section shall operate said coating line on or after March 25, 1995, unless the owner or operator has complied with, and continues to comply with, paragraph (e)(1)(i) and (e)(6)(ii) of this section.

(iii) No owner or operator of a coating line complying by means of paragraph (e)(1)(ii) of this section shall operate said coating line on or after March 25, 1995, unless the owner or operator has complied with, and continues to comply with, paragraphs (e)(1)(ii) and (e)(6)(iii) of this section.

(iv) No owner or operator of a coating line complying by means of paragraph (e)(2) of this section shall operate said coating line on or after March 25, 1995, unless the owner or operator has complied with, and continues to comply with, paragraphs (e)(2) and (e)(6)(iv) of this section.

(8) The control requirements in this paragraph apply to the wood coating line, which coats wooden globe stand components, at Replogle Globes, Inc. (Replogle) Broadview facility in Cook County, Illinois, instead of the control requirements in paragraphs (e)(1) and (e)(2) of this section. Compliance with this paragraph must be demonstrated through the applicable coating analysis test methods and procedures specified in paragraph (a)(4)(i) of this section.

(i) After October 6, 1991, no coatings shall at any time be applied which exceed the following emission limitations for the specified coating.

(A) 6.59 pounds (lbs) Volatile Organic Material (VOM) per gallon of stain (minus water and any compounds which are specifically exempted from the definition of VOM) as applied to coat wooden globe stand components. Such stain consists of #9250 Walnut NGR Stain (RGI # W06000100), #9974 Cherry NGR Stain (RGI # W06003500) and #9943 Ash NGR Stain (RGI # W06003600). The Administrator must be notified at least ten (10) days prior to the use of any replacement stains.

(B) 5.53 lbs VOM per gallon of Sanding Sealer (minus water and any compounds which are specifically exempted from the definition of VOM) as applied to coat wooden globe stand components. Such sealer consists of #15304 High Build Sanding Sealer (RGI # W06003700). The Administrator must be notified at least ten (10) days prior to the use of any replacement sanding sealer.

(C) 5.20 lbs VOM per gallon of lacquer (minus water and any compounds which are specifically exempted from the definition of VOM) as applied to coat wooden globe stand components. Such lacquer consists of #15352 High Build Lacquer (RGI # W06003300). The Administrator shall be notified at least ten (10) days prior to the use of any replacement lacquer.

(ii) After October 6, 1991, the volume of coatings used shall not exceed the following:

(A) 5,000 gallons per year total for all coatings specified in paragraph (e)(8)(i)(A) of this section. The yearly volume of coatings used are to be calculated as follows:

(1) Compute the volume of specified coating used each month by the 15th of the following month.

(2) By the 15th of each month, add the monthly coating use for the 12 previous months (to obtain the yearly volume of coatings used).

(B) 4,000 gallons per year total for all coatings specified in paragraph (e)(8)(i)(B) of this section. The yearly volume of the coatings used are to be calculated as specified in paragraphs (e)(8)(ii)(A)(1) and (e)(8)(ii)(A)(2) of this section.

(C) 5,000 gallons per year total for all coatings specified in paragraph (e)(8)(i)(C) of this section. The yearly volume of coatings used are to be calculated as specified in paragraphs (e)(8)(ii)(A)(1) and (e)(8)(ii)(A)(2) of this section.

(iii) Beginning on October 6, 1991, the owner and operator of the Replogle Globes, Inc. plant in Broadview, Illinois shall keep the following records for each month. All records shall be retained at Replogle Globes, Inc. for three (3) years and shall be made available to the Administrator on request.

(A) the name and identification number of each coating as applied on any wood coating line.

(B) The weight of VOM per volume (determined in accordance with the procedures in paragraph (a)(4)(i) of this section) and the volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each month on any wood coating line.

(9) [Reserved]

(10) Until December 31, 1996, the control and recordkeeping requirements in this paragraph apply to the three solvent-based polyester paper coating lines (Lines C, D and E) at Riverside Laboratories' Kane County, Illinois facility, instead of the control requirements in paragraphs (e)(1) and (e)(2) of this section and the recordkeeping requirements in paragraph (e)(6) of this section. Compliance with this paragraph must be demonstrated through the applicable coating analysis test methods and procedures specified in paragraph (a)(4)(i) of this section. The requirements in paragraphs (e)(1), (e)(2), and (e)(6) of this section shall apply to Riverside on and after December 31, 1996.

(i) After December 21, 1995, no coatings shall at any time be applied on Lines C, D or E which exceed 3.5 pounds (lbs.) volatile organic material (VOM) per gallon of coating (minus water and any compounds which are specifically exempted from the definition of VOM), except as provided in paragraph (e)(10)(ii) of this section.

(ii) After December 21, 1995, the following specifically identified coatings may exceed 3.5 lbs. VOM per gallon of coating (minus water and any compounds which are specifically exempted from the definition of VOM) only if they are applied on Line E and they do not exceed the limits indicated below (minus water and any compounds which are specifically exempted from the definition of VOM):

EXP-5027—4.34 lbs./gallon

PD 75 CLR—4.19 lbs./gallon

PD 75 BRN—4.18 lbs./gallon

SQZ-54—3.88 lbs./gallon

SPX-34GL—3.51 lbs./gallon

(iii) That portion of Riverside's polyester production which is manufactured with the use of any VOC, from Lines C, D, and E, may not exceed the following levels: 35 million square feet per year during and after 1992, 29 million square feet per year during and after 1994, and 25 million square feet during 1996. Compliance with this requirement shall be determined by adding the polyester production from any 12 consecutive months during and after the years indicated, through 1996. That is, the polyester production for any 12 consecutive months starting with January 1992 cannot exceed 35 million square feet; the polyester production from any 12 consecutive months starting with January 1994 cannot exceed 29 million square feet; and the polyester production for the twelve months from January through December 1996 cannot exceed 25 million square feet. Only those square feet of polyester whose production involves the use of VOC need to be restricted by the production levels in this paragraph (e)(10)(iii) of this section.

(iv) By December 21, 1995, Riverside shall certify to the Administrator that its polyester coating operations will be in compliance with paragraphs (e)(10)(i), (e)(10)(ii), and (e)(10)(iii) of this section. Such certification shall include the following:

(A) The name and identification number of each coating as applied on coating lines C, D and E.

(B) The weight of VOM per volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied on each coating line.

(v) The Administrator must be notified at least 10 days prior to the use of any polyester coating not previously identified pursuant to paragraph (e)(10)(iv) of this section. This notification must include the information specified in paragraphs (e)(10)(iv)(A) and (e)(10)(iv)(B) of this section.

(vi) On and after December 21, 1995, Riverside shall collect and record all of the following information each day for each coating and maintain the information at the facility for a period of 3 years:

(A) The name and identification number of each coating as applied.

(B) The weight of VOM per volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each day.

(C) Any record showing a VOM content in excess of the emission limits in paragraph (e)(10)(i) or (e)(10)(ii) of this section shall be reported by sending a copy of such record to the Administrator within 30 days following its collection.

(D) Any VOM besides acetone used in any coating must be identified.

(vii) Starting with the first full month after December 21, 1995, Riverside shall collect and record the figures on polyester production (in square feet), for each month and maintain the information at the facility for a period of at least 3 years.

(viii) Regardless of any other provision of paragraph (e)(10) of this section, after August 21, 1995 no coating which contains any VOM other than acetone shall at any time be applied on Line C, D, or E which exceeds 2.9 lbs. VOM per gallon of coating (minus water and any compounds which are specifically exempted from the definition of VOM).

(f)-(g) [Reserved]

(h) Printing and publishing—(1) Flexographic and rotogravure printing. (i) No owner or operator of a subject flexographic, packaging rotogravure or publication rotogravure printing line shall apply at any time any coating or ink unless the VOM content does not exceed the limitation specified in either paragraph (h)(1)(i)(A) or (B) of this section. Compliance with this paragraph must be demonstrated through the applicable coating or ink analysis test methods and procedures specified in paragraph (a)(4)(i) of this section and the recordkeeping and reporting requirements specified in paragraph (h)(4)(ii) of this section. As an alternative to compliance with paragraph (h)(1)(i) of this section, a subject printing line may meet the requirements of paragraph (h)(1)(ii) or (iii) of this section.

(A) Forty percent VOM by volume of the coating and ink (minus water and any compounds which are specifically exempted from the definition of VOM), or

(B) Twenty-five percent VOM by volume of the volatile content in the coating and ink.

(ii) No owner or operator of a subject flexographic, packaging rotogravure or publication rotogravure printing line shall apply coatings or inks on the subject printing line unless the weighted average, by volume, VOM content of all coatings and inks as applied each day on the subject printing line does not exceed the limitation specified in either paragraph (h)(1)(i)(A) (as determined by paragraph (h)(1)(ii)(A) or (h)(1)(i)(B) (as determined by paragraph (h)(1)(ii)(B) of this section. Compliance with this paragraph must be demonstrated through the applicable coating or ink analysis test methods and procedures specified in paragraph (a)(4)(i) of this section and the recordkeeping and reporting requirements specified in paragraph (h)(4)(iii) of this section.

(A) The following equation shall be used to determine if the weighted average VOM content of all coatings and inks as applied each day on the subject printing line exceeds the limitation specified in paragraph (h)(1)(i)(A) of this section.

eCFR graphic ec07no91.009.gif

View or download PDF

Where:

VOM(i)(A) = The weighted average VOM content in units of percent VOM by volume of all coatings and inks (minus water and any compounds which are specifically exempted from the definition of VOM) used each day,

i = Subscript denoting a specific coating or ink as applied,

n = The number of different coatings and/or inks as applied each day on a printing line,

Ci = The VOM content in units of percent VOM by volume of each coating or ink as applied (minus water and any compounds which are specifically exempted from the definition of VOM),

Li = The liquid volume of each coating or ink as applied in units of l (gal),

Vsi = The volume fraction of solids in each coating or ink as applied, and

VVOMi = The volume fraction of VOM in each coating or ink as applied.

(B) The following equation shall be used to determine if the weighted average VOM content of all coatings and inks as applied each day on the subject printing line exceeds the limitation specified in paragraph (h)(1)(i)(B) of this section.

eCFR graphic ec07no91.010.gif

View or download PDF

Where:

VOM(i)(B) = The weighted average VOM content in units of percent VOM by volume of the volatile content of all coatings and inks used each day,

i = Subscript denoting a specific coating or ink as applied,

n = The number of different coatings and/or inks as applied each day on each printing line,

Ci = The VOM content in units of percent VOM by volume of the volatile matter in each coating or ink as applied,

Li = The liquid volume of each coating or ink as applied in units of l (gal), and

VVMi = The volume fraction of volatile matter in each coating or ink as applied.

(iii) No owner or operator of a subject flexographic, packaging rotogravure or publication rotogravure printing line equipped with a capture system and control device shall operate the subject printing line unless the owner or operator meets the requirements in paragraph (h)(1)(iii) (A), (B) or (C) and paragraphs (h)(1)(iii) (D), (E) and (F) of this section.

(A) A carbon adsorption system is used which reduces the captured VOM emissions by at least 90 percent by weight, or

(B) An incineration system is used which reduces the captured VOM emissions by at least 90 percent by weight, or

(C) An alternative VOM emission reduction system is demonstrated to have at least a 90 percent control device efficiency and the alternative emission reduction system is approved by the Administrator as a SIP or FIP revisions, and

(D) The printing line is equipped with a capture system and control device that provides an overall reduction in VOM emissions of at least:

(1) 75 percent where a publication rotogravure printing line is employed, or

(2) 65 percent where a packaging rotogravure printing line is employed, or

(3) 60 percent where a flexographic printing line is employed, and

(E) The control device is equipped with the applicable monitoring equipment specified in paragraph (a)(4)(iv)(B) of this section and the monitoring equipment is installed, calibrated, operated and maintained according to vendor specifications at all times the control device is in use, and

(F) The capture system and control device are operated at all times when the subject printing line is in operation. The owner or operator shall demonstrate compliance with this paragraph by using the applicable capture system and control device test methods and procedures specified in paragraphs (a)(4) (iii) through (vi) of this section and by complying with the recordkeeping and reporting requirements specified in paragraph (h)(4)(iv) of this section.

(2) Applicability. (i) The limitations of paragraph (h)(1) of this section apply to all flexographic and rotogravure printing lines at a subject facility. All facilities with flexographic and/or rotogravure printing lines are subject facilities unless:

(A) Total maximum theoretical emissions of VOM from all flexographic and rotogravure printing line(s) at the facility never exceed 90.7 Mg (100 tons) per calendar year before the application of capture systems and control devices, or

(B) A federally enforceable construction permit or SIP or FIP revision for all flexographic and rotogravure printing line(s) at a facility requires the owner or operator to limit production or capacity of these printing line(s) to reduce total VOM emissions from all flexographic and rotogravure printing line(s) to 90.7 Mg (100 tons) or less per calendar year before the application of capture systems and control devices.

(ii) Upon achieving compliance with paragraph (h) of this section, the emission source is not required to meet subpart K (sections 215.301 or 215.302) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742). Emission sources exempt from paragraph (h) of this section are subject to subpart K (sections 215.301 or 215.302). Rotogravure or flexographic equipment used for both roll printing and paper coating are subject to paragraph (h) of this section.

(iii) Once subject to the limitations of paragraph (h)(1) of this section, a flexographic or rotogravure printing line is always subject to the limitations of paragraph (h)(1) of this section.

(iv) Any owner or operator of any flexographic or rotogravure printing line that is exempt from the limitations of paragraph (h)(1) of this section because of the criteria in paragraph (h)(2) of this section is subject to the recordkeeping and reporting requirements specified in paragraph (h)(4)(i) of this section.

(3) Compliance schedule. Every owner or operator of a flexographic and/or rotogravure printing line shall comply with the applicable requirements of paragraph (h)(1) of this section and paragraph (h)(4) of this section in accordance with the applicable compliance schedule specified in paragraph (h)(3) (i), (ii), (iii) or (iv) of this section.

(i) No owner or operator of a flexographic or rotogravure printing line which is exempt from the limitations of paragraph (h)(1) of this section because the criteria in paragraph (h)(2) of this section shall operate said printing line on or after July 1, 1991, unless the owner or operator has complied with, and continues to comply with, paragraph (h)(4)(i) of this section.

(ii) No owner or operator of a flexographic or rotogravure printing line complying by means of paragraph (h)(1)(i) of this section shall operate said printing line on or after July 1, 1991, unless the owner or operator has complied with, and continues to comply with, paragraphs (h)(1)(i) and (h)(4)(ii) of this section.

(iii) No owner or operator of a flexographic or rotogravure printing line complying by means of paragraph (h)(1)(ii) of this section shall operate said printing line on or after July 1, 1991, unless the owner or operator has complied with, and continues to comply with, paragraphs (h)(1)(ii) and (h)(4)(iii) of this section.

(iv) No owner or operator of a flexographic or rotogravure printing line complying by means of paragraph (h)(1)(iii) of this section shall operate said printing line on or after July 1, 1991, unless the owner or operator has complied with, and continues to comply with, paragraphs (h)(1)(iii) and (h)(4)(iv) of this section.

(4) Recordkeeping and reporting. The VOM content of each coating and ink and the efficiency of each capture system and control device shall be determined by the applicable test methods and procedures specified in paragraph (a)(4) of this section to establish the records required under paragraph (h)(4) of this section.

(i) Any owner or operator of a printing line which is exempted from the limitations of paragraph (h)(1) of this section because of the criteria in paragraph (h)(2) of this section shall comply with the following:

(A) By July 1, 1991, the owner or operator of a facility to which paragraph (h)(4)(i) of this section is applicable shall certify to the Administrator that the facility is exempt under the provisions of paragraph (h)(2) of this section. Such certification shall include:

(1) A declaration that the facility is exempt from the limitations of the criteria in paragraph (h)(1) of this section because of paragraph (h)(2) of this section, and

(2) Calculations which demonstrate that total maximum theoretical emissions of VOM from all flexographic and rotogravure printing lines at the facility never exceed 90.7 Mg (100 tons) per calendar year before the application of capture systems and control devices. Total maximum theoretical emissions of VOM for a flexograhpic or rotogravure printing facility is the sum of maximum theoretical emissions of VOM from each flexographic and rotogravure printing line at the facility. The following equation shall be used to calculate total maximum theoretical emissions of VOM per calendar year before the application of capture systems and control devices for each flexographic and rotogravure printing line at the facility:

Ep = A × B

Where:

Ep = Total maximum theoretical emissions of VOM from one flexographic or rotogravure printing line in units of kg/year (lbs/year),

A = Weight of VOM per volume of solids of the coating or ink with the highest VOM content as applied each year on the printing line in units of kg VOM/l (lbs VOM/gal) of coating or ink solids, and

B = Total volume of solids for all coatings and inks that can potentially be applied each year on the printing line in units of l/year (gal/year). The instrument and/or method by which the owner or operator accurately measured or calculated the volume of each coating and ink as applied and the amount that can potentially be applied each year on the printing line shall be described in the certification to the Administrator.

(B) On and after July 1, 1991, the owner or operator of a facility referenced in paragraph (h)(4)(i) of this section shall collect and record all of the following information each year for each printing line and maintain the information at the facility for a period of three years:

(1) The name and identification number of each coating and ink as applied on each printing line.

(2) The VOM content and the volume of each coating and ink as applied each year on each printing line.

(C) On and after July 1, 1991, the owner or operator of a facility exempted from the limitations of paragraph (h)(1) of this section because of the criteria in paragraph (h)(2) of this section shall notify the Administrator of any record showing that total maximum theoretical emissions of VOM from all printing lines exceed 90.7 Mg (100 tons) in any calendar year before the application of capture systems and control devices, shall be reported by sending a copy of such record to the Administrator within 30 days after the exceedance occurs.

(ii) Any owner or operator of a printing line subject to the limitations of paragraph (h)(1) of this section and complying by means of paragraph (h)(1)(i) of this section shall comply with the following:

(A) By July 1, 1991, or upon initial start-up of a new printing line, or upon changing the method of compliance from an existing subject printing line from paragraph (h)(1) (ii) or (iii) of this section to paragraph (h)(1)(i) of this section, the owner or operator of a subject printing line shall certify to the Administrator that the printing line will be in compliance with paragraph (h)(1)(i) of this section on and after July 1, 1991, or on and after the initial start-up date. Such certification shall include:

(1) The name and identification number of each coating and ink as applied on each printing line.

(2) The VOM content of each coating and ink as applied each day on each printing line.

(B) On and after July 1, 1991, or on and after the initial start-up date, the owner or operator of a printing line subject to the limitations of paragraph (h)(1) of this section and complying by means of paragraph (h)(1)(i) of this section shall collect and record all of the following information each day for each coating line and maintain the information at the facility for a period of three years:

(1) The name and identification number of each coating and ink as applied on each printing line.

(2) The VOM content of each coating and ink as applied each day on each printing line.

(C) On and after July 1, 1991, the owner or operator of a subject printing line shall notify the Administrator in the following instances:

(1) Any record showing violation of paragraph (h)(1)(i) of this section shall be reported by sending a copy of such record to the Administrator within 30 days following the occurrence of the violation.

(2) At least 30 calendar days before changing the method of compliance with paragraph (h)(1) of this section from paragraph (h)(1)(i) of this section to paragraph (h)(1) (ii) or (iii) of this section, the owner or operator shall comply with all requirements of paragraph (h)(4) (iii)(A) or (iv)(A) of this section respectively. Upon changing the method of compliance with paragraph (h)(1) from paragraph (h)(1)(i) to paragraph (h)(1) (ii) or (iii) of this section, the owner or operator shall comply with all requirements of paragraph (h)(4) (iii) or (iv) of this section, respectively.

(iii) Any owner or operator of a printing line subject to the limitations of paragraph (h)(1) of this section and complying by means of paragraph (h)(1)(ii) of this section shall comply with the following:

(A) By July 1, 1991, or upon initial start-up of a new printing line, or upon changing the method of compliance for an existing subject printing line from paragraph (h)(1) (i) or (iii) of this section to paragraph (h)(1)(ii) of this section, the owner or operator of the subject printing line shall certify to the Administrator that the printing line will be in compliance with paragraph (h)(1)(ii) of this section on and after July 1, 1991, or on and after the initial start-up date. Such certification shall include:

(1) The name and identification number of each printing line which will comply by means of paragraph (h)(1)(ii) of this section.

(2) The name and identification number of each coating and ink available for use on each printing line.

(3) The VOM content of each coating and ink as applied each day on each printing line.

(4) The instrument or method by which the owner or operator will accurately measure or calculate the volume of each coating and ink as applied each day on each printing line.

(5) The method by which the owner or operator will create and maintain records each day as required in paragraph (h)(4)(iii)(B) of this section.

(6) An example of the format in which the records required in paragraph (h)(4)(iii)(B) of this section will be kept.

(B) On and after July 1, 1991, or on and after the initial start-up date, the owner or operator of a printing line subject to the limitations of paragraph (h)(1) of this section and complying by means of paragraph (h)(1)(ii) of this section shall collecting line and maintain the information at the facility for a period of three years:

(1) The name and identification number of each coating and ink as applied on each printing line.

(2) The VOM content and the volume of each coating and ink as applied each day on each printing line.

(3) The daily-weighted average VOM content of all coatings and inks as applied on each printing line.

(C) On and after July 1, 1991, the owner or operator of a subject printing line shall notify the Administrator in the following instances:

(1) Any record showing violation of paragraph (h)(1)(ii) of this section shall be reported by sending a copy of such record to the Administrator within 30 days following the occurrence of the violation.

(2) At least 30 calendar days before changing the method of compliance with paragraph (h)(1) of this section from paragraph (h)(1)(ii) to paragraph (h)(1)(i) or (iii) of this section, the owner or operator shall comply with all requirements of paragraph (h)(4)(ii)(A) or (iv)(A), respectively. Upon changing the method of compliance with paragraph (h)(1) from paragraph (h)(1)(ii) to paragraph (h)(1)(i) or (iii), the owner or operator shall comply with all requirements of paragraph (h)(4)(ii) or (iv) of this section, respectively.

(iv) Any owner or operator of a printing line subject to the limitations of paragraph (h)(1) of this section and complying by means of paragraph (h)(1)(iii) of this section shall comply with the following:

(A) By July 1, 1991, or upon initial start-up of a new printing line, or upon changing the method of compliance for an existing printing line from paragraph (h)(1)(i) or (ii) of this section to paragraph (h)(1)(iii) of this section, the owner or operator of the subject printing line shall perform all tests and submit to the Administrator the results of all tests and calculations necessary to demonstrate that the subject printing line will be in compliance with paragraph (h)(1)(iii) of this section on and after July 1, 1991, or on and after the initial start-up date.

(B) On and after July 1, 1991, or on and after the initial start-up date, the owner or operator of a printing line subject to the limitations of paragraph (h)(1) of this section and complying by means of paragraph (h)(1)(iii) of this section shall collect and record all of the following information each day for each printing line and maintain the information at the facility for a period of three years:

(1) Control device monitoring data.

(2) A log of operating time for the capture system, control device, monitoring equipment and the associated printing line.

(3) A maintenance log for the capture system, control device and monitoring equipment detailing all routine and non-routine maintenance performed including dates and duration of any outages.

(C) On and after July 1, 1991, the owner or operator of a subject printing line shall notify the Administration in the following instances:

(1) Any record showing violation of paragraph (h)(1)(iii) of this section shall be reported by sending a copy of such record to the Administrator within 30 days following the occurrence of the violation.

(2) At least 30 calendar days before changing the method of compliance with paragraph (h)(1) from paragraph (h)(1)(iii) to paragraph (h)(1) (i) or (ii), the owner or operator shall comply with all requirements of paragraph (h)(4) (ii)(A) or (iii)(A) of this section, respectively. Upon changing the method of compliance with paragraph (h)(1) from paragraph (h)(1)(iii) to paragraph (h)(1) (i) or (ii) of this section, the owner or operator shall comply with all requirements of paragraph (h)(4) (ii) or (iii) of this section, respectively.

(5) Heatset-web-offset lithographic printing—(i) Applicability. (A) The limitations of paragraph (h)(5)(ii) of this section apply to all heatset-web-offset lithographic printing lines at a subject facility. All facilities with heatset-web-offset lithographic printing lines are subject facilities unless:

(1) Total maximum theoretical emissions of VOM from all heatset-web-offset lithographic printing lines at the facility never exceed 90.7 Mg (100 tons) per calendar year in the absence of air pollution control equipment, or

(2) A federally enforceable construction permit or SIP or FIP revision for all heatset-web-offset lithographic printing line(s) at a facility requires the owner or operator to limit production or capacity of these printing line(s) to reduce total VOM emissions from all heatset-web-offset lithographic printing line(s) to 90.7 Mg (100 tons) per calendar year or less in the absence of air pollution control equipment, and

(B) Any owner or operator of any heatset-web-offset lithographic printing line that is exempt from the limitations in paragraph (h)(5)(ii) of this section because of the criteria in paragraph (h)(5)(i)(A) of this section shall be subject to the recordkeeping and reporting requirements in paragraph (h)(5)(iii)(A) of this section.

(ii) Specific provisions. No owner or operator of a subject heatset-web-offset printing line may cause or allow the operation of the subject heatset-web-offset printing line unless the owner or operator meets the requirements in paragraph (h)(5)(ii) (A) or (B) of this section and the requirements in paragraphs (h)(5)(ii) (C) and (D) of this section.

(A) An afterburner system is installed and operated that reduces 90 percent of the VOM emissions from the dryer exhaust, or

(B) The fountain solution contains no more than 8 percent, by weight, of VOM and a condensation recovery system is installed and operated that removes at least 75 percent of the non-isopropyl alcohol organic materials from the dryer exhaust, and

(C) The control device is equipped with the applicable monitoring equipment specified in paragraph (a)(4)(iv)(B) of this section and the monitoring equipment is installed, calibrated, operated and maintained according to vendor specifications at all times the control device is in use, and

(D) The control device is operated at all times when the subject printing line is in operation. The owner or operator shall demonstrate compliance with paragraph (h)(5) of this section by using the applicable test methods and procedures specified in paragraphs (a)(4) (i), (iv), and (vi) of this section and by complying with the recordkeeping and reporting requirements specified in paragraph (h)(5)(iii) of this section.

(iii) Recordkeeping and reporting. The VOM content of each fountain solution and ink and the efficiency of each control device shall be determined by the applicable test methods and procedures specified in paragraph (a)(4) of this section to establish the records required under paragraph (h)(5)(iii) of this section.

(A) Any owner or operator of a printing line which is exempted from the limitations of paragraph (h)(5)(ii) of this section because of the criteria in paragraph (h)(5)(i) of this section shall comply with the following:

(1) By July 1, 1991, the owner or operator of a facility to which paragraph (h)(5)(iii)(A) of this section is applicable shall certify to the Administrator that the facility is exempt under the provisions of paragraph (h)(5)(i) of this section. Such certification shall include:

(i) A declaration that the facility is exempt from the limitations of paragraph (h)(5)(ii) of this section because of the criteria in paragraph (h)(5)(i) of this section, and

(ii) Calculations which demonstrate that total maximum theoretical emissions of VOM from all heatset-web-offset lithographic printing lines at the facility never exceed 90.7 Mg (100 tons) per calendar year before the application of air pollution control equipment. Total maximum theoretical emissions of VOM for a heatset-web-offset lithographic printing facility is the sum of maximum theoretical emissions of VOM from each heatset-web-offset lithographic printing line at the facility. The following equation shall be used to calculate total maximum theoretical emissions of VOM per calendar year in the absence of air pollution control equipment for each heatset-web-offset lithographic printing line at the facility.

eCFR graphic ec07no91.011.gif

View or download PDF

Where:

Ep = Total maximum theoretical emissions of VOM from one heatset-web-offset printing line in units of kg/year (lbs/year),

A = Weight of VOM per volume of solids of ink with the highest VOM content as applied each year on the printing line in units of kg VOM/l (lbs VOM/gal) of solids, and

B = Total volume of solids for all inks that can potentially be applied each year on the printing line in units of l/year (gal/year). The instrument or method by which the owner or operator accurately measured or calculated the volume of each ink as applied and the amount that can potentially be applied each year on the printing line shall be described in the certification to the Administrator.

C = The weight percent VOM of the fountain solution with the highest VOM content.

D = The total volume of fountain solution that can potentially be used each year on the printing line in units of l/year (gal/year). The instrument and/or method by which the owner or operator accurately measured or calculated the volume of each fountain solution used and the amount that can potentially be used each year on the printing line shall be described in the certification to the Administrator.

(2) On and after July 1, 1991, the owner or operator of a facility to which paragraph (h)(5)(iii)(A) of this section is applicable shall collect and record all of the following information each year for each printing line and maintain the information at the facility for a period of three years:

(i) The name and identification of each fountain solution and ink as applied on each printing line.

(ii) The VOM content and the volume of each fountain solution and ink as applied each year on each printing line.

(3) On and after July 1, 1991, the owner or operator of a facility exempted from the limitations of paragraph (h)(5)(ii) of this section because of the criteria in paragraph (h)(5)(i) of this section shall notify the Administrator of any record showing that total maximum theoretical emissions of VOM from all printing lines exceed 90.7 Mg (100 tons) in any calendar year in the absence of air pollution control equipment shall be reported by sending a copy of such record to the Administrator within 30 days after the exceedance occurs.

(B) Any owner or operator of a printing line subject to the limitations of paragraph (h)(5)(ii) of this section and complying by means of paragraph (h)(5)(ii)(A) of this section shall comply with the following:

(1) By July 1, 1991, or upon initial start-up of a new printing line, or upon changing the method of compliance for an existing printing line from paragraph (h)(5) (ii)(B) to (ii)(A) of this section, the owner or operator of the subject printing line shall perform all tests and submit to the Administrator the results of all tests and calculations necessary to demonstrate that the subject printing line will be in compliance with paragraph (h)(5)(ii)(A) of this section on and after July 1, 1991, or on and after the initial start-up date.

(2) On and after July 1, 1991, or on and after the initial start-up date, the owner or operator of a printing line subject to the limitations of paragraph (h)(5)(ii) of this section and complying by means of paragraph (h)(5)(ii)(A) of this section shall collect and record the following information each day for each printing line and maintain the information at the facility for a period of three years:

(i) Control device monitoring data.

(ii) A log of operating time for the control device, monitoring equipment and the associated printing line.

(iii) A maintenance log for the control device and monitoring equipment detailing all routine and nonroutine maintenance performed including dates and duration of any outages.

(3) On and after July 1, 1991, the owner or operator of a subject printing line shall notify the Administrator in the following instances:

(i) Any record showing violation of paragraph (h)(5)(ii)(A) of this section shall be reported by sending a copy of such record to the Administrator within 30 days following the occurrence of the violation.

(ii) At least 30 calendar days before changing the method of compliance with paragraph (h)(5)(ii) of this section from paragraph (h)(5) (ii)(A) to (ii)(B), the owner or operator shall comply with all requirements of paragraph (h)(5)(iii)(C)(1) of this section. Upon changing the method of compliance with paragraph (h)(5)(ii) from paragraph (h)(5) (ii)(A) to (ii)(B) of this section the owner or operator shall comply with all requirements of paragraph (h)(5)(iii)(C) of this section.

(C) Any owner or operator of a printing line subject to the limitations of paragraph (h)(5)(ii) of this section and complying by means of paragraph (h)(5)(ii)(B) of this section shall comply with the following:

(1) By July 1, 1991, or upon initial start-up of a new printing line, or upon changing the method of compliance for an existing printing line from paragraph (h)(5) (ii)(A) to (ii)(B) of this section, the owner or operator of the subject printing line shall perform all tests and submit to the Administrator the results of all tests and calculations necessary to demonstrate that the subject printing line will be in compliance with paragraph (h)(5)(ii)(B) of this section on and after July 1, 1991, or on and after the initial start-up date.

(2) On and after July 1, 1991, or on and after the initial start-up date, the owner or operator of a printing line subject to the limitations of paragraph (h)(5)(ii) of this section and complying by means of paragraph (h)(5)(ii)(B) of this section shall collect and record the following information each day for each printing line and maintain the information at the facility for a period of three years:

(i) The VOM content of the fountain solution used each day on each printing line.

(ii) A log of operating time for the control device and the associated printing line.

(iii) A maintenance log for the control device detailing all routine and non-routine maintenance performed including dates and duration of any outages.

(3) On and after July 1, 1991, the owner or operator of a subject printing line shall notify the Administrator in the following instances:

(i) Any record showing violation of paragraph (h)(5)(ii)(B) of this section shall be reported by sending a copy of such record to the Administrator within 30 days following the occurrence of the violation.

(ii) At least 30 calendar days before changing the method of compliance with paragraph (h)(5)(ii) of this section from paragraph (h)(5)(ii)(B) to (h)(5)(ii)(A) of this section, the owner or operator shall comply with all requirements of paragraph (h)(5)(iii)(B)(1) of this section. Upon changing the method of compliance with paragraph (h)(5)(ii) of this section from paragraph (h)(5)(ii)(B) to (h)(5)(ii)(A) of this section, the owner or operator shall comply with all requirements of paragraph (h)(5)(iii)(B) of this section.

(iv) Compliance schedule. Every owner or operator of a heatset-web-offset lithographic printing line shall comply with the applicable requirements of paragraphs (h)(5) (ii) and (iii) of this section in accordance with the applicable compliance schedule specified in paragraph (h)(5)(iv) (A), (B) or (C) of this section.

(A) No owner or operator of a heatset-web-offset lithographic printing line which is exempt from the limitations of paragraph (h)(5)(ii) of this section because of the criteria in paragraph (h)(5)(i) of this section shall operate said printing line on or after July 1, 1991, unless the owner or operator has complied with, and continues to comply with, paragraphs (h)(5)(iii)(A) and (h)(5)(ii)(A) of this section.

(B) No owner or operator of a heatset-web-offset lithographic printing line complying by means of paragraph (h)(5)(ii)(A) of this section shall operate said printing line on or after July 1, 1991, unless the owner or operator has complied with, and continues to comply with, paragraphs (h)(5)(iii)(B) and (h)(5)(ii)(B) of this section.

(C) No owner or operator of a heatset-web-offset lithographic printing line complying by means of paragraph (h)(5)(ii)(B) of this section shall operate said printing line on or after July 1, 1991, unless the owner or operator has complied with, and continues to comply with, paragraph (h)(5)(iii)(C) of this section.

(6) The control and recordkeeping and reporting requirements, as well as the test methods in this paragraph, apply to the rotogravure and flexographic presses at General Packaging Products, Inc.'s (GPP) plant in Chicago, Illinois, instead of the requirements in 40 CFR 52.741(h)(1) through 40 CFR 52.741(h)(5).

(i) After July 1, 1992, no inks or other volatile organic material (VOM) containing materials shall at any time be applied or used which have a higher percent VOM by weight than the following:

(A) 8 percent VOM by weight for waterbased inks as applied on GPP's presses.

(B) 82 percent VOM by weight for solvent based inks as applied on GPP's presses.

(C) 100 percent VOM by weight for all other VOM containing materials (besides inks) as used on GPP's presses.

(ii) After July 1, 1992, the weight of ink and other VOM containing materials used shall not exceed the following:

(A) 200,000 pounds per year total for all waterbased inks, as applied (including dilution material). The yearly weight of waterbased inks used is to be calculated according to the procedure in paragraph (h)(6)(iii) of this section.

(B) 100,008 pounds per year total for all solvent based inks, as applied (including dilution material). The yearly weight of solvent based inks used is to be calculated according to the procedure in paragraph (h)(6)(iii) of this section.

(C) 100,000 pounds per year total (based upon the formulation of the material as it is used on the presses) for all other VOM containing materials (besides inks). The yearly weight of other VOM containing materials is to be calculated according to the procedure in paragraph (h)(6)(iii) of this section.

(iii) The yearly weight of ink/material used is to be calculated as follows:

(A) Compute the weight of ink/material used each month by the 15th of the following month.

(B) By the 15th of each month, add the monthly ink/material usage for the 12 previous months (to obtain the yearly weight of ink/material used).

(iv) Beginning on July 1, 1992, the owner and operator of GPP's plant in Chicago, Illinois, shall keep the following records for each month. All records shall be retained at GPP for 3 years and shall be made available to the Administrator on request:

(A) The name and identification number of each waterbased ink, each solvent based ink, and each other VOM containing material as applied or used on any press.

(B) The pounds of waterbased ink as applied on all presses for each month and the percent VOM by weight for each waterbased ink as applied on any press for each month.

(C) The pounds of solvent based ink as applied on all presses for each month and the percent VOM by weight for each solvent based ink as applied on any press for each month.

(D) The pounds of other (non-ink) VOM containing material used on all presses for each month and the percent VOM by weight for each (non-ink) VOM containing material as used on any press for each month.

(v) Any record showing a violation of paragraph (h)(6)(i) or (h)(6)(ii) of this section shall be reported by sending a copy of such record to the Administrator within 30 days of the violation.

(vi) To determine compliance with paragraphs (h)(6)(i) and (h)(6)(ii) of this section and to establish the records required under paragraph (h)(6)(iv) of this section the percent VOM by weight of each ink and other VOM containing material shall be determined by the applicable test methods and procedures specified in paragraph (a)(4) of this section.

(i) Leaks from synthetic organic chemical and polymer manufacturing equipment—(1) Inspection program for leaks. The owner or operator of a synthetic organic chemical or polymer manufacturing plant subject to paragraph (i) and subpart Q (sections 215.430, 215.431, 215.433, 215.434, 215.435, and 215.437) of Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742) shall, for the purposes of detecting leaks, conduct a component inspection program using the test methods specified in Method 21, 40 CFR part 60, appendix A, consistent with the following provisions:

(i) Test annually those components operated near extreme temperature or pressure such that they would be unsafe to routinely monitor and those components which would require the elevation of monitoring personnel higher than two meters above permanent worker access structures or surfaces.

(ii) Test quarterly all other pressure relief valves in gas service, pumps in light liquid service, valves in light liquid service and in gas service, and compressors.

(iii) If less than or equal to 2 percent of the valves in light liquid service and in gas service tested pursuant to paragraph (i)(1)(ii) of this section are found not to leak for five consecutive quarters, no leak tests shall be required for three consecutive quarters. Thereafter, leak tests shall resume for the next quarter. If that test shows less than or equal to 2 percent of the valves in light liquid service and in gas service are leaking, then no tests are required for the next three quarters. If more than 2 percent are leaking, then tests are required for the next five quarters.

(iv) Observe visually all pump seals weekly.

(v) Test immediately any pump seal from which liquids are observed dripping.

(vi) Test any relief valve within 24 hours after it has vented to the atmosphere.

(vii) Routine instrument monitoring of valves which are not externally regulated, flanges, and equipment in heavy liquid service, is not required. However, any valve which is not externally regulated, flange or piece of equipment in heavy liquid service that is found to be leaking on the basis of sight, smell or sound shall be repaired as soon as practicable but no later than 30 days after the leak is found.

(viii) Test immediately after repair any component that was found leaking.

(ix) Within one hour of its detection, a weatherproof, readily visible tag, in bright colors such as red or yellow, bearing an identification number and the date on which the leak was detected must be affixed on the leaking component and remain in place until the leaking component is repaired.

(x) The following components are exempt from the monitoring requirements in paragraph (i)(1) of this section:

(A) Any component that is in vacuum service, and

(B) Any pressure relief valve that is connected to an operating flare header or vapor recovery device.

(2) Alternative program for leaks. The Administrator shall approve an alternative program of monitoring, recordkeeping, or reporting to that prescribed in paragraph (i) and subpart Q (sections 215.430, 215.431, 215.433, 215.434, 215.435, and 215.437) of Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), upon a demonstration by the owner or operator of such plant that the alternative program will provide plant personnel and USEPA personnel with an equivalent ability to identify and repair leaking components. Any alternative program can only be allowed if approved by the Administrator as a SIP or FIP revision.

(j) Petroleum refining and related industries: asphalt materials—(1) Monitoring program for leaks. (i) The owner or operator of a petroleum refinery subject to subpart R (section 215.445) of Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742) shall, for the purpose of detecting leaks, conduct a component monitoring program consistent with the following provisions:

(A) Test once between March 1 and June 1 of each year, by methods referenced in paragraph (a)(4)(vii) of this section, all pump seals, pipeline valves in liquid service and process drains.

(B) Test once each quarter of each calendar year, by methods referenced in paragraph (a)(4)(vii) of this section, all pressure relief valves in gaseous service, pipeline valves in gaseous service and compressor seals.

(C) Inaccessible valves may be tested once each calendar year instead of once each quarter of each calendar year.

(D) Observe visually all pump seals weekly.

(E) Test immediately any pump seal from which liquids are observed dripping,

(F) Test any relief valve within 24 hours after it has vented to the atmosphere, and

(G) Test immediately after repair any component that was found leaking.

(ii) Storage tank valves and pressure relief devices connected to an operating flare header or vapor recovery device are exempt from the monitoring requirements in paragraph (j)(1)(i) of this section.

(iii) The Administrator may require more frequent monitoring than would otherwise be required by paragraph (j)(1)(i) of this section for components which are demonstrated to have a history of leaking.

(2) Alternative program for leaks. The Administrator may approve an alternative program of monitoring, recordkeeping or reporting to that prescribed in paragraph (j)(1) of this section and subpart R (sections 215.446, 215.448, and 215.449) of Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), upon a demonstration by the owner or operator of a petroleum refinery that the alternative program will provide refinery and USEPA personnel with an equivalent ability to identify and repair leaking components. Any alternative program can only be allowed if approved by the Administrator as a SIP or FIP revision.

(3) Compliance schedule for leaks. The owner or operator of a petroleum refinery shall adhere to the increments of progress contained in the following schedule:

(i) Submit to the Administrator a monitoring program consistent with subpart R (section 215.446) of Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742) prior to September 1, 1990.

(ii) Submit to the Administrator the first monitoring report pursuant to subpart R (section 215.449) of Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742) prior to October 1, 1990.

(k)-(l) [Reserved]

(m) Pharmaceutical manufacturing—(1) Applicability. (i) The rules of paragraph (m) of this section, except for paragraphs (m)(4) through (m)(6) of this section, apply to all emission sources of VOM, including but not limited to reactors, distillation units, dryers, storage tanks for VOL, equipment for the transfer of VOL, filters, crystallizers, washers, laboratory hoods, pharmaceutical coating operations, mixing operations and centrifuges used in manufacturing, including packaging, of pharmaceuticals, and emitting more than 6.8 kg/day (15 lbs/day) and more than 2,268 kg/year (2.5 tons/year) of VOM. If an emission source emits less than 2,268 kg/year (2.5 tons/year) of VOM, the requirements of this paragraph still apply to the emission source if VOM emissions from the emission source exceed 45.4 kg/day (100 lbs/day).

(ii) Notwithstanding paragraph (m)(1)(i) of this section, the air suspension coater/dryer, fluid bed dryers, tunnel dryers, and Accelacotas located in Libertyville Township, Lake County, Illinois shall be exempt from the rules of paragraph (m) of this section, except for paragraphs (m)(4) through (m)(6) of this section, if emissions of VOM not vented to air pollution control equipment do not exceed the following levels:

(A) For the air suspension coater/dryer: 2,268 kg/year (2.5 tons/year);

(B) For each fluid bed dryer: 4,535 kg/year (5.0 tons/year);

(C) For each tunnel dryer: 6,803 kg/year (7.5 tons/year); and

(D) For each Accelacota: 6,803 kg/year (7.5 tons/year).

(iii) Paragraphs (m)(4) through (m)(6) of this section apply to a plant having one or more emission sources that:

(A) Are used to manufacture pharmaceuticals, and

(B) Emit more than 6.8 kg/day (15 lbs/day) of VOM and more than 2,268 kg/year (2.5 tons/year) of VOM, or, if less than 2,268 kg/year (2.5 tons/year), these paragraphs still apply if emissions from one or more sources exceed 45.4 kg/day (100 lbs/day).

(iv) No owner or operator shall violate any condition in a permit when the condition results in exclusion of an emission source from paragraph (m) of this section.

(v) Any pharmaceutical manufacturing source that becomes subject to the provisions of paragraph (m) of this section at any time shall remain subject to the provisions of paragraph (m) of this section at all times.

(vi) Emissions subject to paragraph (m) of this section shall be controlled at all times consistent with the requirements set forth in paragraph (m) of this section.

(vii) Control devices required pursuant to paragraph (m) of this section shall be operated at all times when the source it is controlling is operated.

(viii) Determinations of daily and annual emissions for purposes of paragraph (m)(1) of this section shall be made using both data on the hourly emission rate (or the emissions per unit of throughput) and appropriate daily and annual data from records of emission source operation (or material throughput or material consumption data). In the absence of representative test data pursuant to paragraph (m)(8) of this section for the hourly emission rate (or the emissions per unit of throughput), such items shall be calculated using engineering calculations, including the methods described in appendix B of “Control of Volatile Organic Emissions from Manufacturing of Synthesized Pharmaceutical Products” (EPA-450/2-78-029). (This subparagraph shall not affect the Administrator's authority to require emission tests to be performed pursuant to paragraph (m)(8) of this section.)

(2) Control of reactors, distillation units, crystallizers, centrifuges and vacuum dryers. (i) The owner or operator shall equip all reactors, distillation units, crystallizers, centrifuges and vacuum dryers that are used to manufacture pharmaceuticals with surface condensers or other air pollution control equipment listed in paragraph (m)(2)(i)(B) of this section.

(A) If a surface condenser is used, it shall be operated such that the condenser outlet gas temperature does not exceed:

(1) 248.2 K (−13 °F) when condensing VOM of vapor pressure greater than 40.0kPa (5.8 psi) at 294.3K (70 °F), or

(2) 258.2 K (5 °F) when condensing VOM of vapor pressure greater than 20.0 kPa (2.9 psi) at 294.3 K (70 °F), or

(3) 273.2 K (32 °F) when condensing VOM of vapor pressure greater than 10.0 kPa (1.5 psi) at 294.3 K (70 °F), or

(4) 283.2 K (50 °F) when condensing VOM of vapor pressure greater than 7.0 kPa (1.0 psi) at 294.3 K (70 °F), or

(5) 298.2 K (77 °F) when condensing VOM of vapor pressure greater than 3.45 kPa (0.5 psi) at 294.3 K (70 °F).

(B) If a scrubber, carbon adsorption, thermal afterburner, catalytic afterburner, or other air pollution control equipment other than a surface condenser is used, such equipment shall provide a reduction in the emissions of VOM of 90 percent or more.

(ii) The owner or operator shall enclose all centrifuges used to manufacture pharmaceuticals and that have an exposed VOL surface, where the VOM in the VOL has a vapor pressure of 3.45 kPa (0.5 psi) or more at 294.3 K (70 °F), except as production, sampling, maintenance, or inspection procedures require operator access.

(3) Control of air dryers, production equipment exhaust systems and filters. (i) The owner or operator of an air dryer or production equipment exhaust system used to manufacture pharmaceuticals shall control the emissions of VOM from such emission sources by air pollution control equipment which reduces by 90 percent or more the VOM that would otherwise be emitted into the atmosphere.

(ii) The owner or operator shall enclose all rotary vacuum filters and other filters used to manufacture pharmaceuticals and that have an exposed VOL surface, where the VOM in the VOL has a vapor pressure of 3.45 kPa (0.5 psi) or more at 294 K (70 °F), except as production, sampling, maintenance, or inspection procedures require operator access.

(4) Material storage and transfer. The owner or operator of a pharmaceutical manufacturing plant shall:

(i) Provide a vapor balance system that is at least 90 percent effective in reducing VOM emissions from truck or railcar deliveries to storage tanks with capacities equal to or greater than 7.57 m3 (2,000 gal) that store VOL with vapor pressures greater than 28.0 kPa (4.1 psi) at 294.3 K (70 °F), and

(ii) Install, operate, and maintain pressure/vacuum conservation vents set at 0.2 kPa (0.03 psi) or greater on all storage tanks that store VOL with vapor pressures greater than 10 kPa (1.5 psi) at 294.3 K (70 °F).

(5) In-process tanks. The owner or operator shall install covers on all in-process tanks used to manufacture pharmaceuticals and containing a VOL at any time. These covers must remain closed, except as production, sampling, maintenance or inspection procedures require operator access.

(6) Leaks. The owner or operator of a pharmaceutical manufacturing plant shall repair any component from which a leak of VOL can be observed. The repair shall be completed as soon as practicable but no later than 15 days after the leak is found. If the leaking component cannot be repaired until the process unit is shut down, the leaking component must then be repaired before the unit is restarted.

(7) Other emission sources. The owner or operator of a washer, laboratory hood, tablet coating operation, mixing operation or any other process emission source not subject to paragraphs (m)(2) through (m)(6) of this section, and used to manufacture pharmaceuticals shall control the emissions of VOM from such emission sources by:

(i) Air pollution control equipment which reduces by 81 percent or more the VOM that would otherwise be emitted to the atmosphere, or

(ii) A surface condenser which captures all the VOM which would otherwise be emitted to the atmosphere and which meets the requirements of paragraph (m)(2)(i) of this section.

(8) Testing. (i) Upon request by the Administrator, the owner or operator of any VOM emission source subject to paragraph (m) or exempt from paragraph (m) of this section by virtue of the provisions of paragraph (m)(1) of this section shall, at his own expense, demonstrate compliance to the Administrator by the methods or procedures listed in paragraph (a)(vi)(A) of this section.

(ii) A person planning to conduct a VOM emissions test to demonstrate compliance with paragraph (m) of this section shall notify the Administrator of that intent not less than 30 calendar days before the planned initiation of the test.

(9) Monitoring and recordkeeping for air pollution control equipment—(i) Monitoring. (A) At a minimum, continuous monitors for the following parameters shall be installed on air pollution control equipment used to control sources subject to paragraph (m) of this section:

(1) Destruction device combustion temperature.

(2) Temperature rise across a catalytic afterburner bed.

(3) VOM concentration on a carbon absorption unit to determine breakthrough.

(4) Outlet gas temperature of a refrigerated condenser.

(5) Temperature of a non-refrigerated condenser coolant supply system.

(B) Each monitor shall be equipped with a recording device.

(C) Each monitor shall be calibrated quarterly.

(D) Each monitor shall operate at all times while the associated control equipment is operating.

(ii) Recordkeeping. (A) The owner or operator of a pharmaceutical manufacturing facility shall maintain the following records:

(1) Parameters listed in paragraph (m)(9)(i)(A) of this section shall be recorded.

(2) For sources subject to paragraph (m)(2) of this section, the vapor pressure of VOM being controlled shall be recorded for every process.

(B) For any leak subject to paragraph (m)(6) of this section which cannot be readily repaired within one hour after detection, the following records shall be kept:

(1) The name of the leaking equipment,

(2) The date and time the leak is detected,

(3) The action taken to repair the leak, and

(4) The data and time the leak is repaired.

(C) The following records shall be kept for emission sources subject to paragraph (m)(5) of this section which contain VOL:

(1) For maintenance and inspection:

(i) The date and time each cover is opened,

(ii) The length of time the cover remains open, and

(iii) The reason why the cover is opened.

(2) For production and sampling, detailed written procedures or manufacturing directions specifying the circumstances under which covers may be opened and the procedures for opening covers.

(D) For each emission source used in the manufacture of pharmaceuticals for which the owner or operator of a pharmaceutical manufacturing plant claims emission standards are not applicable, because the emissions are below the applicability cutoffs in paragraph (m)(1)(i) of this section or paragraph (m)(1)(ii) of this section the owner or operator shall:

(1) Maintain a demonstration including detailed engineering calculations of the maximum daily and annual emissions for each such emission source showing that the emissions are below the applicability cutoffs in paragraph (m)(1)(i) or paragraph (m)(1)(ii) of this section, as appropriate, for the current and prior calendar years;

(2) Maintain appropriate operating records for each such emission source to identify whether the applicability cutoffs in paragraph (m)(1)(i) or paragraph (m)(1)(ii) of this section, as appropriate, are ever exceeded; and

(3) Provide written notification to the Administrator within 30 days of a determination that such an emission source has exceeded the applicability cutoffs in paragraph (m)(1)(i) or paragraph (m)(1)(ii) of this section, as appropriate.

(E) Records required under paragraph (m)(9)(ii)(A) of this section shall be maintained by the owner or operator for a minimum of two years after the date on which they are made.

(F) Copies of the records shall be made available to the Administrator upon verbal or written request.

(n)-(p) [Reserved]

(q) Gasoline distribution—(1) Bulk gasoline plants. (i) Subject to paragraph (q)(1)(v) of this section, no person may cause or allow the transfer of gasoline from a delivery vessel into a stationary storage tank located at a bulk gasoline unless:

(A) The delivery vessel and the stationary storage tank are each equipped with a vapor collection system that meets the requirements of paragraph (q)(1)(iv)(D) of this section,

(B) Each vapor collection system is operating,

(C) The delivery vessel displays the appropriate sticker pursuant to the requirements of sections 215.584 (b) or (d) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742),

(D) The pressure relief valve(s) on the stationary storage tank and the delivery vessel are set to release at no less than 0.7 psi or the highest pressure allowed by state or local fire codes or the guidelines of the National Fire Prevention Association, and

(E) The stationary storage tank is equipped with a submerged loading pipe.

(ii) Subject to paragraph (q)(1)(vi) of this section, no person may cause or allow the transfer of gasoline from a stationary storage tank located at a bulk gasoline plant into a delivery vessel unless:

(A) The requirements set forth in paragraphs (q) (1)(i)(A) through (1)(i)(D) of this section are met, and

(B) Equipment is available at the bulk gasoline plant to provide for the submerged filling of the delivery vessel or the delivery vessel is equipped for bottom loading.

(iii) Subject to paragraph (q)(1)(v) of this section, each owner of a stationary storage tank located at a bulk gasoline plant shall:

(A) Equip each stationary storage tank with a vapor control system that meets the requirements of paragraph (q) (1)(i) or (1)(ii) of this section, whichever is applicable,

(B) Provide instructions to the operator of the bulk gasoline plant describing necessary maintenance operations and procedures for prompt notification of the owner in case of any malfunction of a vapor control system, or

(C) Repair, replace or modify any worn out or malfunctioning component or element of design.

(iv) Subject to paragraph (q)(1)(v) of this section, each operator of a bulk gasoline plant shall:

(A) Maintain and operate each vapor control system in accordance with the owner's instructions,

(B) Promptly notify the owner of any scheduled maintenance or malfunction requiring replacement or repair of a major component of a vapor control system,

(C) Maintain gauges, meters or other specified testing devices in proper working order, and

(D) Operate the bulk plant vapor collection system and gasoline loading equipment in a manner that prevents:

(1) Gauge pressure from exceeding 45.7 cm (18 in.) of water and vacuum from exceeding 15.2 cm (6 in.) of water, as measured as close as possible to the vapor hose connection,

(2) A reading equal to or greater than 100 percent of the lower explosive limit (LEL measured as propane) when tested in accordance with the procedure described in “Control of Volatile Organic Compound Leaks from Gasoline Tank Trucks and Vapor Collection Systems”, Appendix B, EPA 450/2-78-051 (which is available for purchase from the National Technical Information Services, 5285 Port Royal Road, Springfield, VA 22161), and

(3) Avoidable leaks of liquid during loading or unloading operations.

(E) Provide a pressure tap or equivalent on the bulk plant vapor collection system in order to allow the determination of compliance with paragraph (q)(1)(iv)(D)(1) of this section, and

(F) Within 15 business days after discovery of any leak by the owner, operator, or the Administrator, repair and retest a vapor collection system which exceeds the limits of paragraph (q)(1)(iv)(D) (1) or (2) of this section.

(v) The requirements of paragraphs (q) (1)(i), (1)(iii) and (1)(iv) of this section, shall not apply to:

(A) Any stationary storage tank with a capacity of less than 2,177 l (575 gal), or

(B) Any bulk gasoline plant whose daily gasoline throughtput is less than 15,140 l (4,000 gal/day) on a thirty-day rolling average.

(vi) The requirements of paragraph (q)(1)(ii) of this section shall only apply to bulk gasoline plants:

(A) Whose daily gasoline throughput is greater than or equal to 15,140 l (4,000 gal/day) on a thirty-day rolling average, and

(B) That either distribute gasoline to gasoline dispensing facilities subject to the requirements of section 215.583(a)(2) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742) or that are in Cook, DuPage, Kane, Lake, McHenry or Will County.

(vii) Any bulk gasoline plant which is ever subject to paragraph (q)(1) (i), (ii), (iii) or (iv) of this section shall always be subject to these paragraphs.

(2) [Reserved]

(r) [Reserved]

(s) Paint and ink manufacturing—(1) Applicability. (i) Paragraph (s) shall apply to all paint and ink manufacturing plants which:

(A) Include process emission sources not subject to subparts (B), (Q) (excluding sections 215.432 and 215.436), (R) (excluding sections 215.447, 215.450, and 215.452), (S), (V), (X), (Y) (sections 215.582, 215.583, and 215.584), or (Z) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), or to paragraphs (d), (e) (excluding paragraph (e)(1)(i)(L)), (h) (excluding paragraph (h)(5)), (i), (j), or (q)(1) of this section; and which as a group both:

(1) Have maximum theoretical emissions of 91 Mg (100 tons) or more per calendar year of VOM if no air pollution control equipment were used, and

(2) Are not limited to less than 91 Mg (100 tons) of VOM emissions per calendar year in the absence of air pollution control equipment, through production or capacity limitations contained in a federally enforceable construction permit or a SIP or FIP revision, or

(B) Produce more than 7,570,820 l (2,000,000 gal) per calendar year of paint or ink formulations, which contain less than 10 percent (by weight) water, and ink formulations not containing as the primary solvents water, Magie oil or glycol.

(ii) For the purposes of paragraph (s) of this section, uncontrolled VOM emissions are the emissions of VOM which would result if no air pollution control equipment were used.

(2) Exemption for waterbase material and heatset-offset ink. The requirements of paragraphs (s)(4) and (s)(5) of this section and paragraph (s)(7)(i) of this section shall not apply to equipment while it is being used to produce either:

(i) Paint or ink formulations which contain 10 percent or more (by weight) water, or

(ii) Inks containing Magie oil and glycol as the primary solvent.

(3) Permit conditions. No person shall violate any condition in a federally enforceable permit when the condition results in exclusion of the plant or an emission source from paragraph (s).

(4) Open-top mills, tanks, vats or vessels. No person shall operate an open-top mill, tank, vat or vessel with a volume of more than 45 l (12 gal) for the production of paint or ink unless:

(i) The mill, tank, vat or vessel is equipped with a cover which completely covers the mill, tank, vat or vessel opening except for an opening no larger than necessary to allow for safe clearance for a mixer shaft. Such cover shall extend at least 1.27 cm (0.5 in.) beyond the outer rim of the opening or be attached to the rim.

(ii) The cover remains closed except when production, sampling, maintenance or inspection procedures require access.

(iii) The cover is maintained in good condition such that, when in place, it maintains contact with the rim of the opening for at least 90 percent of the circumference of the rim.

(5) Grinding mills. (i) No person shall operate a grinding mill for the production of paint or ink which is not maintained in accordance with the manufacturer's specifications.

(ii) No person shall operate a grinding mill fabricated or modified after the effective date of paragraph (s) which is not equipped with fully enclosed screens.

(iii) The manufacturer's specifications shall be kept on file at the plant by the owner or operator of the grinding mill and be made available to any person upon verbal or written request during business hours.

(6) Storage tanks. (i) The owner or operator shall equip tanks storing VOL with a vapor pressure greater than 10 kPa (1.5 psi) at 20 °C (68 °F) with pressure/vacuum conservation vents set as a minimum at + /-0.2 kPa (0.029 psi). These controls shall be operated at all times. An alternative air pollution control system may be used if it results in a greater emission reduction than these controls. Any alternative control system can only be allowed if approved by the Administrator as a SIP or FIP revision.

(ii) Stationary VOL storage containers with a capacity greater than 946 l (250 gal) shall be equipped with a submerged-fill pipe or bottom fill. These controls shall be operated at all times. An alternative control system can only be allowed if approved by the Administrator as a SIP or FIP revision.

(7) Leaks. The owner or operator of a paint or ink manufacturing plant shall, for the purpose of detecting leaks, conduct an equipment monitoring program as set forth below:

(i) Each pump shall be checked by visual inspection each calendar week for indications of leaks, that is, liquids dripping from the pump seal. If there are indications of liquids dripping from the pump seal, the pump shall be repaired as soon as practicable, but no later than 15 calendar days after the leak is detected.

(ii) Any pump, valve, pressure relief valve, sampling connection, open-ended valve and flange or connector containing a fluid which is at least 10 percent VOM by weight which appears to be leaking on the basis of sight, smell or sound shall be repaired as soon as practicable, but no later than 15 calendar days after the leak is detected.

(iii) A weather proof, readily visible tag, in bright colors such as red or yellow, bearing an identification number and the date on which the leak was detected shall be attached to leaking equipment. The tag may be removed upon repair, that is, when the equipment is adjusted or otherwise altered to allow operation without leaking.

(iv) When a leak is detected, the owner or operator shall record the date of detection and repair and the record shall be retained at the plant for at least two years from the date of each detection or each repair attempt. The record shall be made available to any person upon verbal or written request during business hours.

(8) Clean up. (i) No person shall clean paint or ink manufacturing equipment with organic solvent unless the equipment being cleaned is completely covered or enclosed except for an opening no larger than necessary to allow safe clearance for proper operation of the cleaning equipment, considering the method and materials being used.

(ii) No person shall store organic wash solvent in other than closed containers, unless closed containers are demonstrated to be a safety hazard, or dispose of organic wash solvent in a manner such that more than 20 percent by weight is allowed to evaporate into the atmosphere.

(9) Compliance schedule. Every owner or operator of an emission source subject to the control requirements of paragraph (s) of this section shall comply with the requirements of paragraph (s) of this section on and after July 1, 1991.

(10) Recordkeeping and reporting. (i) Upon request by the Administrator, the owner or operator of an emission source which claims to be exempt from the requirements of paragraph (s) of this section shall submit records to the Administrator within 30 calendar days from the date of the request which document that the emission source is in fact exempt from paragraph (s) of this section. These records shall include (but are not limited to) the percent water (by weight) in the paint or ink being produced and the quantity of Magie oil, glycol and other solvents in the ink being produced.

(ii) Every owner or operator of an emission source which is subject to the requirements of paragraph (s) of this section shall maintain all records necessary to demonstrate compliance with those requirements at the facility for three years.

(t) [Reserved]

(u) Miscellaneous fabricated product manufacturing processes—(1) Applicability. (i) The requirements of paragraph (u) of this section shall apply to a plant's miscellaneous fabricated product manufacturing process emission sources which are not included within any of the source categories specified in subparts (B), (Q) (excluding sections 215.432 and 215.436), (R) (excluding sections 215.447, 215.450, and 215.452), (S), (V), (X), (Y) (sections 215.582, 215.583, and 215.584), or (Z) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), or specified in paragraph (d), (e), (h), (i), (j), or (q)(1) of this section; if the plant is subject to paragraph (u) of this section. A plant is subject to paragraph (u) of this section if it contains process emission sources, not regulated by subparts (B), (Q) (excluding sections 215.432 and 215.436), (R) (excluding sections 215.447, 215.450, and 215.452), (S), (V), (X), (Y) (sections 215.582, 215.583, 215.584), or (Z) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), or by paragraph (d), (e) (excluding paragraph (e)(1)(i)(L)), (h) (excluding paragraph (h)(5)), (i), (j), or (q)(1) of this section; which as a group both:

(A) Have maximum theoretical emissions of 91 Mg (100 tons) or more per calendar year of VOM if no air pollution control equipment were used, and

(B) Are not limited to less than 91 Mg (100 tons) of VOM emissions per calendar year in the absence of air pollution control equipment, through production or capacity limitations contained in a federally enforceable construction permit or a SIP or FIP revision.

(ii) If a plant ceases to fulfill the criteria of paragraph (u)(1)(i) of this section, the requirements of paragraph (u) of this section shall continue to apply to a miscellaneous fabricated products manufacturing process emission source which was ever subject to the control requirements of paragraph (u)(3) of this section.

(iii) No limits under paragraph (u) of this section shall apply to emission sources with emissions of VOM to the atmosphere less than or equal to 0.91 Mg (1.0 ton) per calendar year if the total emissions from such sources not complying with paragraph (u)(3) of this section does not exceed 4.5 Mg (5.0 tons) per calendar year.

(iv) For the purposes of paragraph (u) of this section, an emission source shall be considered regulated by a subpart (of the Illinois rules) or paragraph if it is subject to the limits of that subpart (of the Illinois rules) or paragraph. An emission source is not considered regulated by a subpart (of the Illinois rules) or paragraph if its emissions are below the applicability cutoff level or if the source is covered by an exemption.

(v) For the purposes of paragraph (u) of this section, uncontrolled VOM emissions are the emissions of VOM which would result if no air pollution control equipment were used.

(2) Permit conditions. No person shall violate any condition in a permit when the condition results in exclusion of the plant or an emission source from paragraph (u) of this section.

(3) Control requirements. Every owner or operator of an emission source subject to paragraph (u) of this section shall comply with the requirements of paragraph (u)(3) (i), (ii) or (iii) of this section:

(i) Emission capture and control techniques which achieve an overall reduction in uncontrolled VOM emissions of at least 81 percent, or

(ii) For coating lines, the daily-weighted average VOM content shall not exceed 0.42 kg VOM/l (3.5 lbs VOM/gal) of coating as applied (minus water and any compounds which are specifically exempted from the definition of VOM) during any day. Owners and Code 215 (incorporated by reference as specified in 40 CFR 52.742), or

(iii) An alternative control plan which has been approved by the Administrator as a SIP or FIP revision.

(4) Compliance schedule. Every owner or operator of an emission source subject to the control requirements of paragraph (u) of this section shall comply with the requirements of paragraph (u) of this section on and after July 1, 1991.

(5) Testing. Any owner or operator of a VOM emission source which is subject to paragraph (u) of this section shall demonstrate compliance with paragraph (u)(3) of this section by using the applicable test methods and procedures specified in paragraph (a)(4) of this section.

(6) The control requirements in this paragraph apply to the adhesive globe coating operations at Replogle's Broadview facility in Cook County, Illinois, instead of the control requirements in paragraph (u)(3) of this section.

(i) After October 6, 1991, no coatings shall at any time be applied which exceed the following emission limitations for the specified coating.

(A) 7.0 lbs VOM per gallon of adhesive coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied to coat globes. Such coating consists of #7879446 Methylene Chloride (RGI #01004100). The Administrator shall be notified at least ten (10) days prior to the use of any replacement adhesive for coating globes.

(B) [Reserved]

(ii) After October 6, 1991, the volume of coatings used shall not exceed the following:

(A) 572 gallons per year total for all coatings specified in paragraph (u)(6)(i)(A) of this section. The yearly volume of coatings used are to be calculated as follows:

(1) Compute the volume of specified coating used each month by the 15th of the following month.

(2) By the 15th of each month, add the monthly coating use for the 12 previous months (to obtain the yearly volume of coatings used).

(B) [Reserved]

(iii) Beginning on October 6, 1991, the owner and operator of the Replogle Globes, Inc. plant in Broadview, Illinois shall keep the following records for each month. All records shall be retained at Replogle Globes, Inc. for three (3) years and shall be made available to the Administrator on request:

(A) The name and identification number of each coating as applied on any adhesive globe coating line.

(B) The weight of VOM per volume and the volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each month on any adhesive globe coating line.

(7) The control requirements in this paragraph apply to the glass candle container coating line(s) and silk screening machines at the Candle Corporation of America (CCA), Chicago, Illinois facility, instead of the control requirements in paragraph (u)(3) of this section.

(i) After June 1, 1992, no coatings or inks shall at any time be applied, at any coating or ink applicator, which exceed the following emission limitations for the specified coating or ink.

(A) 6.04 pounds (lbs) volatile organic material (VOM) per gallon of clear lacquer/varnish (minus water and any compounds which are specifically exempted from the definition of VOM) as applied to coat glass candle containers. Such clear lacquer/varnish (multi-color) is identified as LP3500. The Administrator must be notified at least 10 days prior to the use of any replacement clear lacquers/varnishes.

(B) 5.23 lbs VOM per gallon of translucent coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied to coat glass candle containers. Such translucent coating (multi-color) is identified as LP3603. The Administrator must be notified at least 10 days prior to the use of any replacement translucent coatings.

(C) 5.84 lbs VOM per gallon of white lacquer (minus water and any compounds which are specifically exempted from the definition of VOM) as applied to coat glass candle containers. Such white lacquer is identified as LP3507. The Administrator must be notified at least 10 days prior to the use of any replacement white lacquers.

(D) 3.40 lbs VOM per gallon of fast dry enamel silk screen printing ink (minus water and any compounds which are specifically exempted from the definition of VOM) as applied to print onto glass candle containers.

(ii) After June 1, 1992, the volume of coating and ink used shall not exceed the following:

(A) 2,164 gallons per month total for all coatings specified in paragraph (u)(7)(i)(A) of this section.

(B) 369 gallons per month total for all coatings specified in paragraph (u)(7)(i)(B) of this section.

(C) 49 gallons per month total for all coatings specified in paragraph (u)(7)(i)(C) of this section.

(D) 50 gallons per month total for all inks specified in paragraph (u)(7)(i)(D) of this Section.

(iii) Beginning on June 1, 1992, the owner and operator of CCA's plant in Chicago, Illinois, shall keep the following records for each month. All records shall be retained at CCA for 3 years and shall be made available to the Administrator on request.

(A) The name and identification number of each coating and ink as applied on any glass candle container coating line or silk screening machine.

(B) The weight of VOM per volume and the volume of each coating and ink (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each month on any glass candle container coating line or silk screening machine.

(iv) After June 1, 1992, no more than 100 gallons per month of cleaning solvent is allowed to be used on the glass candle container coating line(s) at CCA. The only cleaning solvents allowed for use are acetone (identified as LP3525) and methyl ethyl ketone (identified as LP3520). Beginning on June 1, 1992, CCA shall keep monthly records of the type and volume of all cleaning solvents used. All such records shall be retained at CCA for 3 years and shall be made available to the Administrator on request.

(v) After June 1, 1992, no more than 50 gallons per month of cleaning solvent is allowed to be used on the glass candle container silk screening machines at CCA. The only cleaning solvent allowed for use is petroleum naphtha (identified as light aromatic naphtha with 7.28 lbs VOM per gallon, minus water and any compounds which are specifically exempted from the definition of VOM). Beginning on June 1, 1992, CCA shall keep monthly records of the type and volume and the weight of VOM per volume (minus water and any compounds which are specifically exempted from the definition of VOM) of all cleaning solvents used on the glass candle container silk screening machines. All such records shall be retained at CCA for 3 years and shall be made available to the Administrator on request.

(8) The control, recordkeeping and reporting requirements in this paragraph apply to the cellulose food casing manufacturing operations at the Viskase Corporation plant in Bedford Park, Illinois (Cook County) instead of the requirements in paragraph (v) of this section, the other parts of paragraph (u) of this section, and the recordkeeping requirements in paragraph (y) of this section. Unless otherwise stated, the following requirements must be met by Viskase on and after November 21, 1995.

(i) VOM emissions shall never exceed 3.30 tons per day.

(ii) VOM emissions shall not exceed 2.22 tons per day, on a monthly average, during June, July, and August.

(iii) VOM emissions shall not exceed 2.44 tons per day during June, July, and August.

(iv) Compliance with the emission limits in paragraphs (u)(8) (i) through (iii) of this section, and the records in paragraph (u)(8)(v) of this section, shall be determined using an emission factor of “0.72 pounds of VOM emissions per pound of carbon disulfide consumed.”

(v) Viskase must keep the following daily records:

(A) The pounds of carbon disulfide per charge for its Fibrous process. If charges with different levels of carbon disulfide per charge are used the same day, a separate record must be kept for each level of carbon disulfide per charge.

(B) The pounds of carbon disulfide per charge for its NOJAX process. If charges with different levels of carbon disulfide per charge are used the same day, a separate record must be kept for each level of carbon disulfide per charge.

(C) The number of charges per day, for each level of carbon disulfide per charge, used in Viskase's Fibrous process.

(D) The number of charges per day, for each level of carbon disulfide per charge, used in Viskase's NOJAX process.

(E) The total quantity of carbon disulfide used per day in Viskase's Fibrous process, the total quantity of carbon disulfide used per day in Viskase's NOJAX process, and the daily VOM emissions resulting from use of the carbon disulfide.

(F) The monthly use of carbon disulfide, and the monthly VOM emissions resulting from use of the carbon disulfide, during June, July, and August.

(vi) Any violation of the emission limits in paragraphs (u)(8) (i) through (iii) of this section must be reported to USEPA within 30 days of its occurrence.

(vii) In order to determine daily and monthly VOM emissions, the test methods in paragraph (a)(4) of this section may be used in addition to, and take precedence over, the emission factor cited in paragraph (u)(8)(iv) of this section. Method 15 is to be used instead of Methods 18, 25, and 25A when the test methods in paragraph (a)(4) of this section are used to determine VOM emissions from Viskase's cellulose food casing facility.

(v) Miscellaneous formulation manufacturing processes—(1) Applicability. (i) The requirements of paragraph (v) of this section shall apply to a plant's miscellaneous formulation manufacturing process emission sources, which are not included within any of the source categories specified in subpart (B), (Q) (excluding sections 215.432 and 215.436), (R) (excluding sections 215.447, 215.450, and 215.452),(S), (V), (X), (Y) (sections 215.582, 215.583, and 215.584), or (Z) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), or specified in paragraph (d), (e), (h), (i), (j), or (q)(1) of this section; if the plant is subject to paragraph (v) of this section. A plant is subject to paragraph (v) of this section if it contains process emission sources, not regulated by subpart (B), (Q) (excluding sections 215.432 and 215.436), (R) (excluding sections 215.447, 215.450, and 215.452), (S), (V), (X), (Y) (sections 215.582, 215.583, and 215.584), or (Z) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), or by paragraph (d), (e) (excluding paragraph (e)(1)(i)(L)), (h) (excluding paragraph (h)(5)), (i), (j), or (q)(1) of this section; which as a group both:

(A) Have maximum theoretical emissions of 91 Mg (100 tons) or more per calendar year of VOM if no air pollution control equipment were used, and

(B) Are not limited to less than 91 Mg (100 tons) of VOM emissions per calendar year in the absence of air pollution control equipment, through production or capacity limitations contained in a federally enforceable construction permit or a SIP or FIP revision.

(ii) If a plant ceases to fulfill the criteria of paragraph (v)(1)(i) of this section, the requirements of paragraph (v) of this section shall continue to apply to a miscellaneous formulation manufacturing process emission source which was ever subject to the control requirements of paragraph (v)(3) of this section.

(iii) No limits under paragraph (v) of this section shall apply to emission sources with emissions of VOM to the atmosphere less than or equal to 2.3 Mg (2.5 tons) per calendar year if the total emissions from such sources not complying with paragraph (v)(3) of this section does not exceed 4.5 Mg (5.0 tons) per calendar year.

(iv) For the purposes of paragraph (v) of this section, an emission source shall be considered regulated by a subpart (of the Illinois rules) or paragraph if it is subject to the limits of that subpart (of the Illinois rules) or paragraph. An emission source is not considered regulated by a subpart (of the Illinois rules) or paragraph if its emissions are below the applicability cutoff level or if the source is covered by an exemption.

(v) For the purposes of paragraph (v) of this section uncontrolled VOM emissions are the emissions of VOM which would result if no air pollution control equipment were used.

(2) Permit conditions. No person shall violate any condition in a permit when the condition results in exclusion of the plant or an emission source from paragraph (v) of this section.

(3) Control requirements. Every owner or operator of an emission source subject to paragraph (v) of this section shall comply with the requirements of paragraph (v)(3) (i) or (ii) of this section.

(i) Emission capture and control techniques which achieve an overall reduction in uncontrolled VOM emissions of at least 81 percent, or

(ii) An alternative control plan which has been approved by the Administrator as a SIP or FIP revision.

(4) Compliance schedule. Every owner or operator of an emission source subject to the control requirements of paragraph (v) of this section shall comply with the requirements of paragraph (v) of this section on and after July 1, 1991.

(5) Testing. Any owner or operator of a VOM emission source which is subject to paragraph (v) of this section shall demonstrate compliance with paragraph (v)(3) of this section by using the applicable test methods and procedures specified in paragraph (a)(4) of this section.

(6) The control requirements in this paragraph apply to the 7 blenders and 3 moguls of the adhesive coating solution formulation (compounding) operations at the Minnesota Mining and Manufacturing Corporation's (3M) Bedford Park facility in Cook County, Illinois, instead of the control requirements in paragraph (v)(3) of this section.

(i) After September 1, 1991, the following operating restrictions shall apply to 3M's Bedford Park, Illinois, compounding operations.

(A) The combined operating hours for all blenders shall not exceed 8,400 hours per quarter (rolled on a monthly basis). The combined quarterly operating hours of all blenders are to be calculated as follows:

(1) By the 15th of each month, compute the combined monthly operating hours of all blenders during the previous month.

(2) By the 15th of each month, add the monthly operating hours of all blenders for the 3 previous months (to obtain the combined quarterly operating hours of all blenders).

(B) The combined operating hours for all moguls shall not exceed 4,200 hours per quarter (rolled on a monthly basis). The quarterly operating hours of all moguls are to be calculated as follows:

(1) By the 15th of each month, compute the combined monthly operating hours of all moguls during the previous month.

(2) By the 15th of each month, add the monthly operating hours of all moguls for the 3 previous months (to obtain the combined quarterly operating hours of all moguls).

(ii) Beginning on September 1, 1991, the owner and operator of the 3M Bedford Park Plant in Bedford Park, Illinois, shall keep the following records. These records shall be compiled on a monthly basis, be retained at the 3M facility for a period of 3 years, and be made available to the Administrator upon request.

(A) Separate monthly records for each of the 7 blenders identifying each batch and the length of each batch as well as the total monthly hours of operation for all blenders.

(B) Separate monthly records for each of the 3 moguls identifying each batch and the length of each batch as well as the total monthly hours of operation for all moguls.

(w) Miscellaneous organic chemical manufacturing processes—(1) Applicability. (i) The requirements of paragraph (w) of this section shall apply to a plant's miscellaneous organic chemical manufacturing process emission sources which are not included within any of the source categories specified in subparts (B), (Q) (excluding sections 215.432 and 215.436), (R) (excluding sections 215.447, 215.450, and 215.452), (S), (V), (X), (Y) (sections 215.582, 215.583, and 215.584), or (Z) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), or specified in paragraph (d), (e), (h), (i), (j), or (q)(1) of this section; if the plant is subject to paragraph (w) of this section. A plant is subject to paragraph (w) of this section if it contains process emission sources, not regulated by subparts (B), (Q) (excluding sections 215.432 and 215.436), (R) (excluding sections 215.447, 215.450, and 215.452), (S), (V), (X), (Y) (sections 215.582, 215.583, and 215.584), or (Z) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), or by paragraph (d), (e) (excluding paragraph (e)(1)(i)(L)), (h) (excluding paragraph (h)(5)), (i), (j), or (q)(1) of this section; which as a group both:

(A) Have maximum theoretical emissions of 91 Mg (100 tons) or more per calendar year of VOM if no air pollution control equipment were used, and

(B) Are not limited to less than 91 Mg (100 tons) of VOM emissions per calendar year in the absence of air pollution control equipment, through production or capacity limitations contained in a federally enforceable construction permit or a SIP or FIP revision.

(ii) If a plant ceases to fulfill the criteria of paragraph (w)(1)(i) of this section, the requirements of paragraph (w) of this section shall continue to apply to a miscellaneous organic chemical manufacturing process emission source which was ever subject to the control requirements of paragraph (w)(3) of this section.

(iii) No limits under paragraph (w) of this section shall apply to emission sources with emissions of VOM to the atmosphere less than or equal to 0.91 Mg (1.0 ton) per calendar year if the total emissions from such sources not complying with paragraph (w)(3) of this section does not exceed 4.5 Mg (5.0 tons) per calendar year.

(iv) For the purposes of paragraph (w) of this section, an emission source shall be considered regulated by a subpart (of the Illinois rules) or paragraph if it is subject to the limits of that subpart (of the Illinois rules) or paragraph. An emission source is not considered regulated by a subpart (of the Illinois rules) or paragraph if its emissions are below the applicability cutoff level or if the source is covered by an exemption.

(v) For the purposes of paragraph (w) of this section, uncontrolled VOM emissions are the emissions of VOM which would result if no air pollution control equipment were used.

(2) Permit conditions. No person shall violate any condition in a permit when the condition results in exclusions of the plant or an emission source from paragraph (w) of this section.

(3) Control requirements. Every owner or operator of an emission source subject to paragraph (w) of this section shall comply with the requirements of paragraph (w)(3)(i) or (ii) of this section.

(i) Emission capture and control techniques which achieve an overall reduction in uncontrolled VOM emissions of at least 81 percent, or

(ii) An alternative control plan which has been approved by the Administrator as a SIP or FIP revision.

(4) Compliance schedule. Every owner or operator of an emission source subject to the control requirements of paragraph (w) of this section shall comply with the requirements of paragraph (w) of this section on and after July 1, 1991.

(5) Testing. Any owner or operator of a VOM emission source which is subject to paragraph (w) shall demonstrate compliance with paragraph (w)(3) of this section by using the applicable test methods and procedures specified in paragraph (a)(4) of this section.

(x) Other emission sources—(1) Applicability. (i) The requirements of paragraph (x) of this section shall apply to a plant's VOM emission sources, which are not included within any of the source categories specified in subpart (B), (Q) (excluding sections 215.432 and 215.436), (R) (excluding sections 215.447, 215.450, and 215.452), (S), (V), (X), (Y) (sections 215.582, 215.583, and 215.584), or (Z) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), or specified in paragraph (d), (e), (h), (i), (j), (q)(1), (s), (u), (v) or (w) of this section; if the plant is subject to paragraph (x) of this section. A plant is subject to paragraph (x) of this section if it contains process emission sources, not regulated by subpart (B), (Q) (excluding sections 215.432 and 215.436), (R) (excluding sections 215.447, 215.450, and 215.452), (S), (V), (X), (Y) (sections 215.582, 215.583, and 215.584), or (Z) of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), or by paragraph (d), (e) of this section (excluding paragraph (e)(1)(i)(L)), (h) (excluding paragraph (h)(5)), (i), (j), or (q)(1) of this section; which as a group both:

(A) Have maximum theoretical emissions of 91 Mg (100 tons) or more per calendar year of VOM if no air pollution control equipment were used, and

(B) Are not limited to less than 91 Mg (100 tons) of VOM emissions per calendar year in the absence of air pollution control equipment, through production or capacity limitations contained in a federally enforceable construction permit or a SIP of FIP revision.

(ii) If a plant ceases to fulfill the criteria of paragraph (x)(1)(i) of this section, the requirements of paragraph (x) of this section shall continue to apply to an emission source which was ever subject to the control requirements of paragraph (x)(3) of this section.

(iii) No limits under paragraph (x) of this section shall apply to emission sources with emissions of VOM to the atmosphere less than or equal to 2.3 Mg (2.5 tons) per calendar year if the total emissions from such sources not complying with paragraph (x)(3) of this section does not exceed 4.5 Mg (5.0 tons) per calendar year.

(iv) For the purposes of paragraph (x) of this section, an emission source shall be considered regulated by a subpart (of the Illinois rules) or paragraph if it is subject to the limits of that subpart (of the Illinois rules) or paragraph. An emission source is not considered regulated by a subpart (of the Illinois rules) or paragraph of its emissions are below the applicability cutoff level or if the source is covered by an exemption.

(v) The control requirements in paragraphs (u), (v), (w), and (x) of this section shall not apply to sewage treatment plants, vegetable oil processing plants, coke ovens (including by-product recovery plants), fuel combustion sources, bakeries, barge loading facilities, jet engine test cells, pharmaceutical manufacturing, production of polystyrene foam insulation board (including storage and extrusion of scrap where blowing agent is added to the polystyrene resin at the plant), production of polystyrene foam packaging (not including storage and extrusion of scrap where blowing agent is added to the polystyrene resin at the plant), and iron and steel production.

(2) Permit conditions. No person shall violate any condition in a permit when the condition results in exclusion of the plant or an emission source from paragraph (x) of this section.

(3) Control requirements. Every owner or operator of an emission source subject to paragraph (x) of this section shall comply with the requirements of paragraph (x)(3) (i), (ii) or (iii) of this section.

(i) Emission capture and control equipment which achieve an overall reduction in uncontrolled VOM emissions of at least 81 percent, or

(ii) For coating lines, the daily-weighted average VOM content shall not exceed 0.42 kg VOM/l (3.5 lbs VOM/gal) of coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied during any day. Owners and operators complying with this paragraph are not required to comply with section 215.301 of 35 Ill. Adm. Code 215 (incorporated by reference as specified in 40 CFR 52.742), or

(iii) An alternative control plan which has been approved by the Administrator as a SIP or FIP revision.

(4) Compliance schedule. Every owner or operator of an emissions source which is subject to paragraph (x) of this section shall comply with the requirements of paragraph (x) of this section on and after July 1, 1991.

(5) Testing. Any owner or operator of a VOM emission source which is subject to paragraph (x) of this section shall demonstrate compliance with paragraph (x)(3) of this section by using the applicable test methods and procedures specified in paragraph (a)(4) of this section.

(6) The control requirements in this paragraph apply to the varnish operations at the General Motors Corporation, Electro-Motive Division Plant (GMC Electro-Motive), LaGrange, Illinois, instead of the control requirements in paragraph (x)(3) of this section.

(i) After July 1, 1991, no coatings shall at any time be applied which exceed the following emission limitations for the specified coating.

(A) 8.0 lbs VOM per gallon of coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied at each coating applicator to coat Nomex rings. Such coating consists of Monsanto Skybond 705 Polyamide Resin (EMD P/N 9088817) and diluents. The Administrator must be notified at least 10 days prior to the use of any replacement coating(s) and/or diluents for coating Nomex rings.

(B) 6.8 lbs VOM per gallon of coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied at each coating applicator for any coatings not specified in paragraph (x)(6)(i)(A) of this section.

(ii) After July 1, 1991, the volume of coatings used shall not exceed the following:

(A) 600 gallons per year total for all coatings specified in paragraph (x)(6)(i)(A) of this section. The yearly volume of coatings used are to be calculated as follows:

(1) Compute the volume of specified coating used each month by the 15th of the following month.

(2) By the 15th of each month, add the monthly coating use for the 12 previous months (to obtain the yearly volume of coatings used).

(B) 28,500 gallons per year total for all coatings other than those specified in paragraph (x)(6)(i)(A) of this section. The yearly volume of coatings used are to be calculated as specified in paragraphs (x)(6)(ii)(A)(1) and (x)(6)(ii)(A)(2) of this section.

(iii) Beginning on July 1, 1991, the owner and operator of the General Motors Corporation Electro-Motive Division Plant in LaGrange, Illinois shall keep the following records for each month. All records shall be retained at General Motors for 3 years and shall be made available to the Administrator on request.

(A) The name and identification number of each coating as applied on any coating line within the varnish operation.

(B) The weight of VOM per volume and the volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each month on any coating line within the varnish operation.

(7) The control, recordkeeping, and monitoring requirements in this paragraph apply to the aluminum rolling mills at the Reynolds Metals Company's McCook Sheet & Plate Plant in McCook, Illinois (Cook County) instead of the control requirements and test methods in the other parts of paragraph (x), and the recordkeeping requirements in paragraph (y) of this section. All of the following requirements must be met by Reynolds on and after July 7, 1995.

(i) Only organic lubricants with initial and final boiling points between 460 degrees F and 635 degrees F, as determined by a distillation range test using ASTM method D86-90, are allowed to be used at Reynolds' aluminum sheet cold rolling mills numbers 1 and 7. All incoming shipments of organic lubricant for the number 1 and 7 mills must be sampled and each sample must undergo a distillation range test to determine the initial and final boiling points using ASTM method D86-90. A grab rolling lubricant sample shall be taken from each operating mill on a monthly basis and each sample must undergo a distillation range test, to determine the initial and final boiling points, using ASTM method D86-90.

(ii) An oil/water emulsion, with no more than 15 percent by weight of petroleum-based oil and additives, shall be the only lubricant used at Reynolds' aluminum sheet and plate hot rolling mills, 120 inch, 96 inch, 80 inch, and 145 inch mills. A grab rolling lubricant sample shall be taken from each operating mill on a monthly basis and each sample shall be tested for the percent by weight of petroleum-based oil and additives by ASTM Method D95-83.

(iii) The temperature of the inlet supply of rolling lubricant for aluminum sheet cold rolling mills numbers 1 and 7 shall not exceed 150 °F, as measured at or after (but prior to the lubricant nozzles) the inlet sump. The temperature of the inlet supply of rolling lubricant for the aluminum sheet and plate hot rolling mills, 120 inch, 96 inch, 80 inch, and 145 inch mills shall not exceed 200 °F, as measured at or after (but prior to the lubricant nozzles) the inlet sump. Coolant temperatures shall be monitored at all the rolling mills by use of thermocouple probes and chart recorders or electronic data recorders.

(iv) All distillation test results for cold mill lubricants, all percent oil test results for hot mill lubricants, all coolant temperature recording charts and/or temperature data obtained from electronic data recorders, and all oil/water emulsion formulation records, shall be kept on file, and be available for inspection by USEPA, for three years.

(8) The control and recordkeeping requirements in this paragraph apply to the silk screen presses and associated ovens, cleaning operations and laminators at Parisian's Novelty Company (Parisian), Chicago, Illinois, facility, instead of the control requirements in paragraphs (x)(8) (u)(3) and (x)(3) of this section and the recordkeeping requirements in paragraph (x)(8)(y) of this section.

(i) After March 1, 1993, no coatings or inks shall at any time be applied, at any coating or ink applicator, which exceed the following emission limitations for the specified coating or ink.

(A) 6.65 pounds (lbs) volatile organic material (VOM) per gallon of ink (minus water and any compounds which are specifically exempted from the definition of VOM) as applied on Parisian's silk screen presses.

(B) 6.4 lbs VOM per gallon of adhesive coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied on Parisian's laminators. Such adhesive is identified as MIX #963.

(ii) After March 1, 1993, the volume of coating and ink used shall not exceed the following:

(A) 2,556 gallons per year total for all inks. The yearly volume of inks used is to be calculated as follows:

(1) Compute the volume of ink used each month by the 15th of the following month.

(2) By the 15th of each month, add the monthly ink usage for the 12 previous months (to obtain the yearly volume of ink used).

(B) 780 gallons per year total for all coatings specified in paragraph (x)(8)(i)(B) of this section. The yearly volume of coatings used are to be calculated as specified in paragraphs (x)(8)(ii)(A)(1) and (x)(8)(ii)(A)(2) of this section.

(iii) Beginning on March 1, 1993, the owner and operator of Parisian's plant in Chicago, Illinois, shall keep the following records for each month. All records shall be retained at Parisian for 3 years and shall be made available to the Administrator on request.

(A) The name and identification number of each coating as applied on any laminator.

(B) The weight of VOM per volume and the volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each month on any laminator.

(C) The weight of VOM per volume and the volume of each type of ink (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each month on any screen press.

(iv) After March 1, 1993, no more than 84 gallons per year of denatured alcohol may be used for cleaning labels at Parisian. The yearly volume of denatured alcohol used is to be calculated as specified in paragraphs (x)(8)(ii)(A)(1) and (x)(8)(ii)(A)(2) of this section. Beginning on March 1, 1993, Parisian shall keep monthly records of the type, volume, and VOM content of all solvents used for label cleaning. These records shall be retained at Parisian for 3 years and shall be made available to the Administrator on request.

(v) After March 1, 1993, no more than 7,932 gallons per year of screen wash #956 may be used on Parisian's screen cleaner. The yearly volume of screen wash #956 used is to be calculated as specified in paragraphs (x)(8)(ii)(A)(1) and (x)(8)(ii)(A)(2) of this section. Beginning on March 1, 1993, Parisian shall keep monthly records of the type, volume, and VOM content of all cleaning compounds used on Parisian's screen cleaner. These records shall be retained at Parisian for 3 years and shall be made available to the Administrator on request.

(vi) After March 1, 1993, only those cleaners specifically identified in paragraphs (x)(8)(iv) and (x)(8)(v) of this section may be used at Parisian.

(9) The control requirements in this paragraph apply to the process sources listed in paragraph (x)(9)(i)(A) of this section at the Nalco Chemical Company facility in Bedford Park, Illinois, instead of the control requirements in paragraph (x)(3) of this section.

(i) Production and Operation Restrictions.

(A) On and after October 1, 1992, the maximum volatile organic compound (VOC) emissions per batch, the 12-month rolling average number of batches per year, and the peak limit of batches per month shall not exceed the following limits:

SourceMaximum VOC emissions, lb/batch12-mo. rolling average limit batch/yrPeak batch limit, batch/month
(1) System 1 charge0.1628033
System 1 purge1.35
(2) 24-T-156, 1572.6030033
(3) 28-T-217, 2340.2340245
(4) 28-T-214-2165.7060365
(5) 20-R-182, 1850.02728
(6) 20-R-1300.0734038
(7) 20-R-1550.2125429
(8) 20-WT-1740.2125429
(9) 12-T-97-994.6E-4 lb/hr8,760 hr/yr744 hr/mo
(10) 12-T-954.0E-6 lb/hr8,760 hr/yr744 hr/mo
(11) 12-T-967.7E-5 lb/hr8,760 hr/yr744 hr/mo
(12) 12-T-67, 730.003 lb/hr8,760 hr/yr744 hr/mo
(13) 20-T-121-1220.8531234
(14) 20-T-123-1255.461668
(15) 20-T-140, 1428.060065
(16) 20-T-1590.3141646
(17) 20-R-193, 2009.854059
(18) 32-R-3000.1836541
(19) 32-T-3020.2136541
(20) 32-T-3040.2173081
(21) 32-T-3140.2336541
(22) 32-T-3220.2136541
(23) 32-T-3280.2336541
(24) 10-T-610.001365—containing organic31—containing organic
(25) 24-T-441, 1660.1273081
(26) 25-T-284, 440, 443-4440.2873081
(27) 25-T-1704E-610412
(28) Tank truck loading0.12 lb/truck1,600 trucks/yr134 trucks/mo
(29) System 20.3628033
(30) System 42.8828033
(31) 25-R-1640.1036541
(32) 25-R-2050.1436541
(33) Drum station3.511,005110
(34) V-4SAC1.5625429
(35) 20-CT-15513.9025429
(36) 12-SE-1001.10 lb/hr8,760 hr/yr744 hr/mo
(37) Drum exhaust hood A1.00365—involving use of organic material31—involving use of organic material
(38) 24-T-2300.9873081
(39) 8-CT-10.002 lb/hr8,760 hr/yr744 hr/mo
(40) 9-CT-10.002 lb/hr8,760 hr/yr744 hr/mo
(41) 10-CT-10.005 lb/hr8,760 hr/yr744 hr/mo
(42) 22-CT-10.003 lb/hr8,760 hr/yr744 hr/mo
(43) 25-CT-10.005 lb/hr8,760 hr/yr744 hr/mo
(44) 25-CT-20.002 lb/hr8,760 hr/yr744 hr/mo
(45) 29-CT-10.002 lb/hr8,760 hr/yr744 hr/mo
(46) 32-CT-10.005 lb/hr8,760 hr/yr744 hr/mo
(47) 36-CT-10.002 lb/hr8,760 hr/yr744 hr/mo
(48) 32-T-3250a36541
(49) 26-R-1950.1a36541
(50) Continuous polymer-blending0.1 lb/hra2,000 hr/yr
(51) Portafeed washer booth 10.84 lb/hrb4,160 hr/yr744 hr/mo
(52) Portafeed washer booth 20.84 lb/hrb8,736 hr/yr744 hr/mo
(53) 32-T-3924.4E-710412

aAssumed value.

bBased on monitoring data.

(B) The following equation shall be used to calculate maximum VOC emissions per batch for the process sources listed in paragraphs (x)(9)(i)(A)(1) (charge only and (2) through (28) and (53) of this section:

Where:

ER = VOC emission rate;

Qo = Quantity of organic per batch or charge rate;

eCFR graphic er21mr95.000.gif

View or download PDF

Mv = Molecular weight of the volatile component;

P = Partial pressure of the volatile component for mixtures of liquid made up with more than one chemical; or vapor pressure for pure liquids made up of only one organic chemical; and

Constant1 = (7.45 gal/ft3) × (385 ft3/mole)x(760 mmHg).

(C) The following equation shall be used to calculate the VOC emissions per batch from the process sources listed in paragraph (x)(9)(i)(A)(1) of this section (purge only) and (29) through (32) of this section:

eCFR graphic er21mr95.001.gif

View or download PDF

Where:

PR = Nitrogen purge rate; and

Constant2 = (385 ft3/mole) × (760 mmHg).

(D) The following equation shall be used to calculate the VOC emissions per batch from the drum station listed at paragraph (x)(9)(i)(A)(33) of this section:

ER(1b/batch) = (0.40 × [ER28-T-217-218]) + (0.60 × [ER28-T-214-216])

(E) The following equation shall be used to calculate the VOC emissions per batch from the V-4SAC listed at paragraph (x)(9)(i)(A)(34) of this section:

eCFR graphic er21mr95.002.gif

View or download PDF

Where:

FR1mmHg = Maximum air flow rate to maintain 1 mmHg;

Ma = Molecular weight of air; and

Pv2 = Vapor pressure of organic at 65 °F and 760 mmHg.

(F) The following equation shall be used to calculate the VOC emissions per batch from 20-CT-155 listed at paragraph (x)(9)(i)(A)(35) of this section:

eCFR graphic er21mr95.003.gif

View or download PDF

Where:

ERtot = Total system emission rate calculated using the following equation:

eCFR graphic er21mr95.004.gif

View or download PDF

Where:

Pv1 = Vapor pressure of organic at 200 °F and 350 mmHg.

(G) The following equation shall be used to calculate the VOC emissions per hour from 12-SE-100 listed at paragraph (x)(9)(i)(A)(36) of this section:

ER(lb/hr) = Evap (gm/cm2 sec) × area (cm2) × 3600 sec/hr

Where:

Evap = Evaporation rate from a surface 8.93 cm × 8.9 cm (lb/[cm2] [sec]) calculated using the following equation:

Evap = 10−7 Mv0.71 × [0.034 (Pe − Pd)1.25 + 156 (Pe − Pd)]

Where:

Pe = Partial pressure of the component from the spilled liquid;

Pd = Partial pressure of the component in the incident air stream, assumed to be 0 mmhg; and

Area = Surface area of the liquid.

(H) The following equation shall be used to calculate the VOC emissions per batch from the drum exhaust hood A listed at paragraph (x)(9)(i)(A)(37) of this section:

eCFR graphic er21mr95.005.gif

View or download PDF

Where:

FR = Air flow rate.

(I) The following equation shall be used to calculate the VOC emissions per batch from 24-T-230 listed at paragraph (x)(9)(i)(A)(38) of this section:

eCFR graphic er21mr95.006.gif

View or download PDF

Where:

VH = Head space volume at heated temperature 135 °F;

VA = Head space volume at ambient temperature 68 °F;

PP135 °F = Partial pressure of volatile component at 135 °F.

Constant3 = (434 ft3/mole)(7.45 gal/ft3) × (760 mmHg)

(J) The following equations shall be used to calculate the VOC emissions per batch from the process sources listed in paragraph (x)(9)(i) (39) through (47) of this section:

eCFR graphic er21mr95.007.gif

View or download PDF

Where:

VR = Refill volume;

t = Time between refills;

org = Fraction of organic component in product;

CB = Concentration of chemical B fed 3 times/week;

VT = Tower volume;

dB = Density of chemical B;

CC = Concentration of chemical C fed continuously;

Evap = Evaporation rate; and

dc = Density of chemical C.

(K) The number of batches for each process source shall be calculated as follows:

(1) Compute the monthly number of batches for each process source by the 15th day of the following month.

(2) By the 15th day of each month, add the monthly number of batches for each process source for the 12 previous months to obtain the total number of batches per year.

(ii) Recordingkeeping. (A) On and after October 1, 1992, the owner and operator of the Nalco Chemical Company facility in Bedford Park, Illinois, shall keep the following records for all process sources listed in paragraphs (x)(9)(i)(A) (1) through (53) of this section. These records shall be maintained for the units specified in paragraphs (x)(9)(i) (A) through (K) of this section, be compiled on a monthly basis, be retained at the facility for a period of 3 years, and be made available to the Administrator upon request.

(B) [Reserved]

(1) Calculations of the pounds per batch or pounds per hour (as appropriate) for each batch for each process source. This includes the information necessary for each calculation.

(2) The monthly number of batches for each process source.

(3) The total number of batches per year for the 12 previous months for each process source.

(10) The control requirements in this paragraph apply to the storage tanks listed in paragraph (x)(10)(i)(A) of this section at the Nalco Chemical Company facility in Bedford Park, Illinois, instead of the control requirements in paragraph (x)(3) of this section.

(i) Production and Operation Restrictions. (A) On and after October 1, 1992, the product of the molecular weight of vapor in each storage tank (Mv), the true vapor pressure at bulk liquid conditions for each tank (P), and the paint factor (Fp); the storage tank maximum yearly throughput for each tank; and the maximum monthly throughput for each tank shall not exceed the following limits:

Tank No.MV × P × Fp, (lb) (mmhg)/lb-moleYearly throughput, gal/yrMonthly throughput, gal/month
(1) 24-T-14745.456,2504,688
(2) 24-T-150227266,45022,204
(3) 24-T-151227266,45022,204
(4) 24-T-158N18.9173,83014,486
(5) 24-T-158C18.0110,1909,183
(6) 24-T-158S1.1752,0104,334
(7) 24-T-160226.8266,45022,204
(8) 24-T-161227182,45015,204
(9) 24-T-16247393,9007,825
(10) 20-T-1013.7290,2907,525
(11) 20-T-1021.80122,90010,242
(12) 20-T-10342023,9601,997
(13) 20-T-104180475,90039,659
(14) 20-T-10537052,3604,363
(15) 20-T-1061,210623,10051,926
(16) 20-T-10729490,0407,503
(17) 20-T-1081,36081,4706,789
(18) 20-T-1091,390167,06013,922
(19) 20-T-15318035,0002,917
(20) 20-T-131a
(21) 20-T-132a
(22) 20-T-133a
(23) 20-T-134a
(24) 20-T-135a
(25) 20-T-13629.5307,71026,580
(26) 20-T-137a
(27) 20-T-13829.5307,71026,580
(28) 32-T-305288785,55065,462
(29) 32-T-30666.5165,35013,779
(30) 32-T-30766.5294,75024,563
(31) 32-T-30866.5128,47010,706
(32) 32-T-31066.577,2906,441
(33) 32-T-31166.5182,13015,177
(34) 32-T-31950.0688,95057,413
(35) 32-T-32050.0688,95057,413
(36) 32-T-32670.0248,44020,703
(37) 32-T-33170.0489,54040,795
(38) 32-T-33270.070,3805,865
(39) 32-T-33370.0270,85022,571
(40) 32-T-33470.0210,61018,267
(41) 32-T-33570.0418,20034,850
(42) 32-T-33670.0632,46052,706
(43) 32-T-33779853,8504,488
(44) 17-T-20627,000300,76025,063
(45) 17-T-20827,000300,76025,063
(46) 17-T-2072.48180,18015,016
(47) 17-T-2092.48180,18015,016
(48) 24-T-515331216,86018,072
(49) 25-T-2821.421,920,410160,034
(50) 25-T-2831.421,920,410160,034
(51) 24-T-44218.090,9907,583
(52) 17-T-21047.9582,99048,583
(53) 17-T-21147.9582,99048,583
(54) 17-T-212508728,42060,702
(55) 17-T-213508728,42060,702
(56) 17-T-40150.0131,97010,998
(57) 17-T-40215.0120,16010,014
(58) 17-T-4036.20127,77010,648
(59) 17-T-40426.51,601,510133,460
(60) 17-T-40550.0113,8309,486
(61) 17-T-40640.0231,03019,253
(62) 17-T-407206135,18011,265
(63) 17-T-409395327,41027,285
(64) 17-T-410395129,29010,774
(65) 17-T-41150.0213,87017,843
(66) 17-T-41250.0277,84023,153
(67) 17-T-41450.072,9206,077
(68) 17-T-41550.056,1404,678
(69) 17-T-416395393,550