';


Title 40 Part 1051 → Subpart H → §1051.720

Title 40 → Chapter I → Subchapter U → Part 1051 → Subpart H → §1051.720

Electronic Code of Federal Regulations e-CFR

Title 40 Part 1051 → Subpart H → §1051.720

e-CFR data is current as of December 6, 2019

Title 40Chapter ISubchapter UPart 1051Subpart H → §1051.720


Title 40: Protection of Environment
PART 1051—CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES AND VEHICLES
Subpart H—Averaging, Banking, and Trading for Certification


§1051.720   How do I calculate my average emission level or emission credits?

(a) Calculate your average emission level for each type of recreational vehicle or engine for each model year according to the following equation and round it to the nearest tenth of a g/km or g/kW-hr. Use consistent units throughout the calculation.

(1) For exhaust emissions:

(i) Calculate the average emission level as:

eCFR graphic er08no02.011.gif

View or download PDF

Where:

FELi = The FEL to which the engine family is certified.

ULi = The useful life of the engine family.

Productioni = The number of vehicles in the engine family.

(ii) Use U.S.-directed production projections for initial certification, and actual U.S.-directed production volumes to determine compliance at the end of the model year.

(2) For vehicles that have standards expressed as g/kW-hr and a useful life in kilometers, convert the useful life to kW-hr based on the maximum engine power and an assumed vehicle speed of 30 km/hr as follows: UL (kW-hr) = UL (km) × Maximum Engine Power (kW) ÷ 30 km/hr. (Note: It is not necessary to include a load factor, since credit exchange is not allowed between vehicles certified to g/kW-hr standards and vehicles certified to g/km standards.)

(3) For evaporative emission standards expressed as g/m2/day, use the useful life value in years multiplied by 365.24 and calculate the average emission level as:

eCFR graphic er13jy05.019.gif

View or download PDF

Where:

FEL i = The FEL to which the engine family is certified, as described in paragraph (a)(4) of this section.

Production i = The number of vehicles in the engine family times the average internal surface area of the vehicles' fuel tanks.

(4) Determine the FEL for calculating credits under paragraph (a)(3) of this section using any of the following values:

(i) The FEL to which the tank is certified, as long as the FEL is at or below 3.0 g/m2/day.

(ii) 10.4 g/m2/day. However, if you use this value to establish the FEL for any of your tanks, you must use this value to establish the FEL for every tank not covered by paragraph (a)(4)(i) of this section.

(iii) The measured permeation rate of the tank or the measured permeation rate of a thinner-walled tank of the same material. However, if you use this approach to establish the FEL for any of your tanks, you must establish an FEL based on emission measurements for every tank not covered by paragraph (a)(4)(i) of this section.

(b) If your average emission level is below the average standard, calculate credits available for banking according to the following equation and round them to the nearest tenth of a gram:

eCFR graphic er08no02.013.gif

View or download PDF

(c) If your average emission level is above the average standard, calculate your preliminary credit deficit according to the following equation, rounding to the nearest tenth of a gram:

eCFR graphic er08no02.014.gif

View or download PDF

[67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40505, July 13, 2005; 73 FR 59256, Oct. 8, 2008]


© e-CFR 2019

FR | USC | CFR | eCFR